QUICKSTART GUIDE English · 简体中文 · Deutsch · Français · Italiano · Español · Pусский · Português · 日本語 · 한국어 · 繁體中文 · عربية لغة
❶ ❷ ❸ ❹ ❺ ❻ ❶ Latch ❺ Microphone ❸ Micro-USB port ❼ Release ❷ MicroSD card slot ❹ Lens ❻ ❽ ❼ ⓬ ❺ Status indicator Power / Shutter / Enter button ❽❾ ❿ ❼ EN The Basics ❶ ⓫ ⓭ ❾ Photo indicator ⓫ Video indicator ❿ ⓬ Mode button Standard 1/4'' mounting point ⓭ Reset pinhole 1
EN Fold to Switch Between 180° 3D / 360° Modes Hold down the release to release the latch, allowing you to switch the EVO to 180° mode. Or fold the camera, and slide in the latch to switch it to 360° mode. Note: Slide the latch until it clicks. When the camera is turned on, and the camera mode switches successfully, you will hear a beep sound.
EN Before You Start ❶ Before use, please insert an exFAT format microSD card of speed class UHS-I and V30 to ensure normal recording. The maximum storage space is 128GB. For specific compatible MicroSD card models, see https://www.insta360.com/r/evo_microsd ❷ Before use, ensure that EVO has sufficient battery. If not, use a 5V/2A adapter to charge.
EN Fixed to a tripod Power on / off + Reset Press and hold the round button on the top of the camera for 3 seconds to turn on / off the camera; Press and hold the round button on the top of the camera for 15 seconds to reset and turn off the camera. Mode button Shoot When the camera is on, press the round button on the top of the camera to take photos; When the camera is on, press the mode button to switch the camera to Video mode, then press the round button on the top of the camera to shoot video.
EN Download the Companion App Scan the QR code as shown on the right (https://www.insta360.com/r/evo_download) or search "Insta360 EVO" in the App Store / Google Play to download the companion app. WiFi Control ❶ ❷ ❸ Turn on your smartphone's WiFi and Bluetooth. Press and hold the round button on the top of the camera for 3 seconds to turn on the camera. Having successfully installed the app, tap the camera icon at the bottom of the screen and select "Connect via WiFi".
EN ❹ Having successfully connected to the camera, you can take photos or shoot videos via the app. Back Camera mode * Remaining battery Photo VR Preview Album * There are 2 camera modes: 2D VR 360°, 3D VR 180°.
EN 3D VR Glasses After selecting VR Preview in the app, use the included 3D VR glasses as shown below to view 180° 3D photos or videos.
IE-QSG-CM.2 Shenzhen Arashi Vision Company Limited ADD: 6F, Building A, Logan Century Center, 23 Haixiu Road, Bao'an District, Shenzhen, Guangdong, China WEB: www.insta360.com TEL: (+86) 400-833-4360 EMAIL: service@insta360.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Model No.: CINEVOX/A, CINEVOX Operation Frequency: 2412MHz~2472MHz for WIFI 2.4G 5180MHz~5240MHz for WIFI 5G 5745MHz ~ 5825MHz for WIFI 5.8G Maximum Power: WIFI 2.4G: 15.30dBm（E.I.R.P） WIFI 5G: 13.80dBm（E.I.R.P） WIFI 5.8G: 6.70dBm（E.I.R.P） Manufacturer: Shenzhen Arashi Vision Company Limited Address of Manufacturer: 6/F, Building A, Logan Century Center, Haixiu Road, Bao'an District, Shenzhen, China USB versions 2.0 Receiver category 1 The operating temperature of the device between 0℃ to 45℃.
Shenzhen Arashi Vision Company Limited EU Declaration of Conformity for Radio Equipment Directive (RED) 2014/53/EU We, Shenzhen Arashi Vision Company Limited hereby, declare that the essential requirements set out in the Radio Equipment Directive (RED) 2014/53/EU have been fully fulfilled on our product with indication below: Address: 6/F, Building A, Logan Century Center, Haixiu Road, Bao'an District, Shenzhen, China Product Name: Insta360 EVO Model: CINEVOX/A, CINEVOX Brand Name: Insta360 Hardware Versio
Shenzhen Arashi Vision Company Limited The following standards have been applied for the investigation of compliance: Draft ETSI EN 301 489-1 V2.2.0 (2017-03) Final draft ETSI EN 301 489-3 V2.1.1 (2017-03) Draft ETSI EN 301 489-17 V3.2.0 (2017-03) ETSI EN 300 328 V2.1.1 (2016-11) ETSI EN 301 893 V2.1.1 (2017-05) ETSI EN 300 440 V2.2.
Shenzhen Arashi Vision Company Limited And apply notified body assessment: MiCOM Labs Inc 75 Boulder Court, Pleasanton, California94566 USA Furthermore, the ISO requirement for the in-process quality control procedure as well as the manufacturing process has been reached. The technical document as well as the test reports will be kept for a period at least 10 years after the last product has been manufactured at the disposal of the relevant national authorities of any Member State for inspection.
