DUO TM Multi-Use Pressure Cooker Safety, Maintenance & Warranty Important Safeguards Care & Cleaning Troubleshooting Warranty Contact Information Full Manual, How to Videos and Recipes available online at instantpot.com.au Register your product today at instantpot.com.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed: 1. READ THE GETTING STARTED GUIDE AND ALL INSTRUCTIONS, SAFEGUARDS AND WARNINGS BEFORE OPERATING THE APPLIANCE. FAILURE TO FOLLOW THESE SAFEGUARDS AND INSTRUCTIONS MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. 2. o not let children near the pressure cooker when in use. Children shall D not play with the appliance. 3. Do not put the pressure cooker into a heated oven. 4.
IMPORTANT SAFEGUARDS 12. T he heating element surface is subject to residual heat after use, do not touch. 13. W hen cooking doughy food, gently shake the cooker before opening the lid to avoid food ejection. 14. B efore each use, check that the valves are not obstructed. Refer to the “Getting Started Guide”. 15. N ever use the pressure cooker in its pressurized mode for deep or shallow frying of food. 16.
IMPORTANT SAFEGUARDS 23. D o not immerse the cooker base in water. To protect against electrical shock, do not immerse the cord, power plug, or cooker base in any liquid. 24. A lways make sure the sealing ring is completely set in the groove on the inside of the sealing ring rack. 25. Avoid spillage on the connector. 26. Please turn off and unplug the appliance before cleaning, maintenance or relocation and whenever it is not in use. SAVE THESE INSTRUCTIONS.
Care & Cleaning Unplug your Instant Pot and let it cool before cleaning. Let all surfaces dry thoroughly before use.
Troubleshooting Register your product today at www.instantpot.com.au/support/register Problem Difficulty closing lid Possible Reason Solution Sealing ring not properly installed Reposition sealing ring, ensure it is snug behind sealing ring rack. Float valve in the popped-up position Gently press the float valve downward with a long utensil. Contents in cooker are still hot Turn steam release handle to “Venting” position, then lower lid onto cooker base slowly, allowing heat to dissipate.
Troubleshooting Problem Possible Reason Food debris on float valve or float valve silicone cap Solution Remove float valve from lid and clean thoroughly; perform “Initial Test Run” to check for function and record findings. Contact Customer Care. Check for scorching on bottom of inner pot; remove if necessary. Too little liquid in the inner pot Float valve does not rise Add thin, water-based liquid to inner pot based on size: 3L - 1 cup | 5.
Troubleshooting Problem Possible Reason Solution C1 C2 C6 Faulty sensor Contact Customer Care. Temperature is too high because inner pot is not placed in the cooker base Press Cancel and wait for heating element to cool; ensure there are no foreign objects in cooker base; insert or reposition inner pot in cooker base and re-enter commands. C6H C6L C5 Temperature is too high because there is no water in inner pot Check for scorching on bottom of inner pot; remove if necessary.
Warranty Limited Warranty This Limited Warranty is issued by Corelle Brands (Australia) Pty Ltd (Corelle Brands Australia) and is effective for one year from the date of original consumer purchase. Proof of original purchase date and return of your appliance is required to obtain service under this Limited. Return of your appliance to us will be done in accordance with our instructions only.
©2019 Corelle Brands (Australia) Pty Ltd. Distributed by Corelle Brands (Australia) Pty Ltd. 9c Commercial Road, Kingsgrove, NSW, 2208, Australia Register your product today at: instantpot.com.au/support/register Contact Customer Care: Ph 1800 251 643 or 02 9317 1000 support@instantpot.com.au instantpot.com.au © 2019 Corelle Brands (Australia) Pty Ltd.
