In-LineLinc™ Dimmer INSTEON® Remote Control In-Line Dimmer Owner’s Manual (rev 5.
In-LineLinc Dimmer – Features and Benefits ........................................................................................... 3 Features..................................................................................................................................................... 3 What’s in the Box? ..................................................................................................................................... 4 Preparing to Install In-LineLinc ...........................
In-LineLinc Dimmer – Features and Benefits Congratulations on purchasing the high-quality INSTEON In-LineLinc Dimmer Switch. With this easyinstall module, you can add conveniently hidden, fully-dimmable remote control to not only the lights wired to In-LineLinc, but also other INSTEON devices.
What’s in the Box? - In-LineLinc Dimmer Quick Start Guide Two (2) mounting screws Three (3) wire nuts Preparing to Install In-LineLinc CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This product is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. Use indoors only.
6) Referring to the diagram at right and the table below, use the included wire nuts to connect the fixture’s Line, Load, Neutral and Ground wires to In-LineLinc’s corresponding wires. In-LineLinc Wire Bare copper White Red Black 7) 8) 9) 10) 11) 12) Wall Box Wires Ground (commonly bare copper, green wire or green screw) Neutral (commonly white wire bundle) Load (light, fan, etc.) Line (100 - 277V to Ground) Enable power to the switch from the circuit breaker or fuse panel.
Linking In-LineLinc Dimmer as an INSTEON Responder Be sure to link In-LineLinc Dimmer to an INSTEON controller before you finish installing the fixture. Refer to your controller device’s Quick Start Guide or Owner’s Manual to properly link it to In-LineLinc. Most controllers use the procedure below: 1) Put your controller into linking mode. For most INSTEON controllers, press and hold the Set button for 3 seconds or the On/scene button for 10 seconds.
When setting the ramp rate, the speed is determined using the load’s brightness level. Refer to the table below while programming to set the desired ramp rate: 1) Using either the local ON and OFF buttons or a controller (if In-LineLinc Dimmer is already linked to one), adjust the load wired to In-LineLinc Dimmer to the brightness level that corresponds with your desired ramp rate: Brightness Level Ramp Rate (seconds) 90-100% 0.1 77-87% 0.2 65-74% 0.3 52-61% 2 39-48% 2 26-35% 4.5 13-23% 6.
Factory Reset Factory Reset clears all user settings from In-LineLinc Dimmer, including INSTEON scenes, on-levels, ramp rates, X10 addresses, etc. 1) 2) 3) 4) Make sure In-LineLinc Dimmer is unlinked from all controllers. Turn off the breaker supplying power to In-LineLinc Dimmer’s fixture. Wait 10 seconds. Push in Set button and hold it. While continuing to hold in the Set button, have a partner turn on the circuit breaker. 5) Release the Set button.
Specifications General Product Name In-LineLinc Dimmer Brand INSTEON Manufacturer Product Number 2475D, INSTEON In-LineLinc Dimmer UPC 689076402743 Patent Number Protected under U.S. and foreign patents (see www.insteon.com) Warranty Two years, limited Operation On-Levels 32 locally, increments of 1% with software Ramp Rates 0.
Voltage 120 volts AC +/- 10%, 60 Hertz, single phase Power Wire Leads 6", 16 AWG, stranded,600V, 105°C insulation, ends stripped and tinned, LINE (black), LOAD (red), NEUTRAL (white) Ground Lead 6”, 18 AWG, stranded, bare copper Maximum Dimmer Load 600 watts (uses 12-Amp triac dimmer) Maximum Amps 2.5 amps Standby power consumption 0.
interference with older X10 BoosterLinc technology. Upgrade to INSTEON-compatible BoosterLinc modules (#4827). In-LineLinc doesn't always respond to an INSTEON controller. The INSTEON controller may have been reset without first unlinking In-LineLinc from it. Relink In-LineLinc to the INSTEON controller. See Adding In-LineLinc Relay as an INSTEON Responder. The light turned on by itself.
controller. Turn off the circuit breaker and try reinstalling After wiring in InIn-LineLinc is issuing an error In-LineLinc. If you are still experiencing an LineLinc, the unit lets out beep because the unit is wired error beep, consult an electrician to help you a continuous beep. incorrectly. install In-LineLinc. In-LineLinc trips the Arc Fault Circuit Interrupter (AFCI). The AFCI might be too sensitive.
Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S.
