On/Off Outdoor Module Owner’s Manual 2634-222 Page 1 of 13 2634-222 - Rev: 2/11/2019 9:16 AM
TABLE OF CONTENTS About On/Off Outdoor Module ................................................................................................................................... 3 Features and Benefits ............................................................................................................................................... 3 Before Installation ................................................................................................................................................
About On/Off Outdoor Module On/Off Outdoor Module is a simple way to remotely control any plug-in device, in or outside your home, at the touch of a button. Send commands to On/Off Outdoor Module from any INSTEON controller, or link it to other INSTEON devices as a controller.
Before Installation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. On/Off Outdoor Module is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. On/Off Outdoor Module is not designed nor approved for use on power lines other than 120V 60Hz, single phase.
Using On/Off Outdoor Module Local Control Operation Connected load/responders Double-tap Tap Set Button On/Off On/Off (instant) LED Green/ Red LED Activity LED Status/Setup Mode Solid green Load is on Solid red Load is off Blinking green Linking mode Blinking red Unlinking mode Adjust Local Settings LED On or Off Default = On This setting is only adjustable via software or a central controller.
INSTEON Setup Some products have subtle differences in their setup procedures. Please refer to the other devices’ owner’s manuals for details. INSTEON Controllers, Responders and Links Let’s define a few terms. The INSTEON “transmitter” is called a controller The INSTEON “receiver” is called a responder The association between the controller and responder is called a link Link Controller Responder Note that a link is one way.
Groups Devices in a group share all the same settings (e.g., on-level, ramp rate). This keeps all group members synchronized. Every device in a group is both a controller of, and responder to, all the other devices. The most common example of a group is a 3-way lighting circuit (2 switches). For simplicity, we will assume that the desired group level is on.
Remove On/Off Outdoor Module as a Controller If you no longer want On/Off Outdoor Module to control another device (or are removing On/Off Outdoor Module from your network) it is important that you follow the instructions below for each responder.
Specifications General Product name On/Off Outdoor Module Brand/manufacturer INSTEON Manufacturer product number 2634-222 UPC 813922013375 Warranty 2 years, limited INSTEON INSTEON powerline mesh repeater Yes INSTEON RF mesh repeater Yes INSTEON controller Yes INSTEON responder Yes Maximum links/scenes 400 LED Green when load is on, red when load is off Blinks red or green during setup Beep on button press No Local control Yes On Off On Off Commands supported as controller Comm
Screw On/Off Outdoor Module connections None Case color Dark gray Set button Yes Plastic UV stabilized polycarbonate Beeper Yes LED 1, Red-Green Dimensions 2.75"W x 4.32"H x 1.27"D (with 6" lead) 70mm W x 110mm H x 32mm D (with 150mm lead) Weight .465lbs (7.2 oz) .
Troubleshooting Problem The Status LED on On/Off Outdoor Module is not turning on and won’t control the load On/Off Outdoor Module won’t link to or work with a controller Possible Cause Solution On/Off Outdoor Module may not be getting power Make sure On/Off Outdoor Module is not plugged into a switched outlet that is turned off The controller or might have been reset without unlinking On/Off Outdoor Module Re-link On/Off Outdoor Module to the controller The controller and On/Off Outdoor Module may
Phase Bridge Detect Beacon/RF Range Test On/Off Outdoor Module automatically bridges the electrical phases in your home (via communications with other dual-band devices on the “other phase”). This is only important in 2-phase homes with powerline-only INSTEON products or buildings with both 2- and 3- phase circuits. The phase bridge detect beacon can also be used as an RF range test to see if your devices are within communication range. You will need at least one other INSTEON dual-band device installed.
Certification and Warranty Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S.
