INSTEON LED Bulb 2672-222 Owner’s Manual
Contents Getting Started INSTEON LED Bulb 4 Device Overview Do Not Connect to a Dimmer Leave Your Fixture On Linking INSTEON Links Understanding Linking Linking to the INSTEON Hub using the iOS or Android App Linking with a Single-Button Controller Linking with a Multi-Button Controller Multi-Linking or Making a Scene Unlinking from a Single-Button Controller Unlinking from a Multi-Button Controller Multi-Unlinking or Removing a Scene Software-Only Features Ramp Rate 6 8 9 10 11 12 13 14 16 Disable
Getting Started Everything you need to quickly get up and running.
INSTEON LED Bulb Device Overview Do Not Connect to a Dimmer INSTEON LED Bulb dims using INSTEON commands. INSTEON ID X Leave Your Fixture On If your switch is OFF, communication with the LED Bulb is lost. Linking Your LED Bulb does not have a set button. To link manually, unscrew the LED Bulb for a moment and reinsert. ON ON ? If your fixture is controlled by a wall switch, consider wiring as always-on.
INSTEON Links INSTEON devices can stand alone and function as a local switch or dimmer, but their real power comes when they are connected together to form a control system. Most INSTEON devices can control one another and be the recipient of control. The process of associating multiple INSTEON devices to one another is called linking.
Understanding Linking Links are One-Way When linking INSTEON devices, the links that are created are one-way. Links Remember a Device’s State The current state of the controlled device is stored in the link: on, off or dimmed. NEW NEW 75% A B Switch A will turn Switch B on and off but Switch B cannot turn Switch A on or off. X Controllers INSTEON devices that can turn other devices on or off are called controllers. Switch Lamp Dimmer The switch will turn on the Lamp Dimmer to 75% brightness.
Understanding Linking Controller-Only Some devices, like sensors, can only control other devices. Responder-Only Some devices cannot control other devices; these devices only receive INSTEON commands. NEW NEW X X Motion Sensor Dimmer Switch The Motion Sensor will turn on the Switch but the switch cannot control the Motion X Sensor. Grouping Devices You may want to group together two devices, for example, in a virtual-three way configuration. For INSTEON, this is called cross linking.
Linking to the INSTEON Hub using the iOS or Android App 1 From Rooms, navigate to All Devices. 2 Tap the Add button. All Devices Rooms All Devices Check-In Favorites Back Door Bathroom Bedroom Bathroom Bedroom Hallway Font Door Garage Door Garage Light Kitchen Living Room Outside Motion Sensor Outside Lights 72º 72º 3 Add Select LED Bulb from the list of devices. 4 When prompted, turn on your fixture and screw in the LED Bulb. The Bulb will double-beep.
Linking with a Single-Button Controller 1 On your INSTEON controller, press and hold the set button until the device beeps. 2 Make sure your fixture is On and then screw in the LED Bulb. Your LED Bulb will double-beep. ON ON Your INSTEON controller will now control your LED Bulb.
Linking with a Multi-Button Controller 1 On your INSTEON controller, tap the desired control button and then press and hold the set button until the device beeps. 2 Make sure your fixture is On and then screw in the LED Bulb. Your LED Bulb will double-beep. A ON B ON Your INSTEON controller will now control your LED Bulb.
Multi-Linking or Making a Scene 1 On your INSTEON controller, press and hold the set button until the device beeps, then tap the set button. 2 A Adjust your scene members to their desired state: on, off, or brightness level if dimming. 50% 72% LED Bulb LED Bulb 30% ON Lamp 3 Appliance B 3 One at a time, screw in your LED Bulbs. For other devices, press and hold the set button until they double-beep. 4 Tap the set button on your INSTEON controller to finish building your scene.
Unlinking from a Single-Button Controller 1 3 On your INSTEON controller, press and hold the set button until the device beeps. 2 Press and hold the set button again until the device beeps. Make sure your fixture is On and then screw in the LED Bulb. Your LED Bulb will double-beep. X ON ON ON Your INSTEON controller will no longer control your LED Bulb.
Unlinking from a Multi-Button Controller 1 On your INSTEON controller, tap the desired control button and then press and hold the set button until the device beeps. 2 Press and hold the set button again until the device beeps. A B 3 Make sure your fixture is On and then unscrew and reinsert the LED Bulb. Your LED Bulb will doublebeep. X ON ON ON Your INSTEON controller will no longer control your LED Bulb.
Multi-Unlinking or Removing a Scene 1 On your INSTEON controller, press and hold the set button until the device beeps. Press and hold the set button again, then tap the set button. 2 One at a time, unscrew and reinsert your LED Bulbs. For other devices, press and hold the set button until they double-beep. A ON B C 3 Tap the set button on your INSTEON controller to exit MultiUnlinking mode. ON X ® ® Your INSTEON controller will no longer control your INSTEON devices.
Software-Only Features Most INSTEON devices contain features that can only be enabled, disabled or modified using INSTEON control software such as HouseLinc and an INSTEON PowerLine Modem.
Software-Only Features Ramp Rate Customize the speed at which the LED Bulb fades on or off. Default is 0.5 seconds, maximum duration of 8 minutes. Instant Disable Linking on Power-up Prevents LED Bulb from entering linking mode each time power is disconnected and reapplied. Default is off. LINKING 0.
Always-On Wiring Because LED Bulb needs constant power, if you have a light fixture that is controlled by a wall switch, you might consider wiring that wall switch as “Always-On” so that flipping the switch will not disconnect LED Bulb from power. Replacing the wall switch with an INSTEON Switch will provide full control for any INSTEON device in your home.
Always-On Wiring 1 Turn off power to your switch at the electrical service panel. 2 Remove the old switch and disconnect the wires. If your box lacks neutral wires, stop and contact support. WIKI ON ON ON ON 1 OFF ON ON or 2 ! Neutral Wire ON ON ON Circuit Breakers Fuse Panel ½” 12mm 3 Connect the Dimmer Switch wires to the identified wires in the junction box. The red load wire is not used and, instead, capped.
Always-On Wiring 4 Mount the Dimmer Switch into the junction box with the LED bar on the left and turn power on to the switch at the circuit breaker panel. 5 Test your switch by tapping the paddle to turn On and Off. Your LED Bulb will not change but the status lights on the switch will. 6 To link your switch to the LED Bulb, press and hold the set button until the device beeps. 7 Unscrew and reinsert your LED Bulb for a moment and reinsert. Your LED Bulb will double-beep.
Appendix Everything else you might need to know about your INSTEON product.
INSTEON Glossary Controller Responder Blinking The INSTEON transmitter The INSTEON receiver LED turning on and off repeatedly Dual-Band An INSTEON device that can send and receive both INSTEON powerline signals and INSTEON radio frequency signals Ramp Rate The speed at which the load fades on or off On-Level The preset brightness level a device will return to when turned on INSTEON A dual-band, mesh networking technology developed by INSTEON.
Specifications General Brand Key Application Product Number UPC Patent Warranty INSTEON Low energy, remote control lighting 2672-222 US 813922013023 Protected under US and Foreign Patents (see www.insteon.com/ patents) 2 years, limited INSTEON Features INSTEON RF RF Frequency Yes 915.
Specifications Operation Lumens Lumens per Watt Color Rendering Index Color Temperature Status LED On Levels Ramp Rate 591 66 83.90 2700 K None 32 0.125 seconds to 8 minutes (software-only) Mechanical Installation Color Dimensions Weight Operating Environment Operating Temperature Range Operating Humidity Range E27 Medium Edison screw base White 2.8” diameter, 4.7” length 72mm diameter, 119mm length 6.
Troubleshooting LED Bulb won’t link to other INSTEON Devices Your LED Bulb may be out of range of other INSTEON Devices or a large appliance may be generating electrical noise, disrupting the INSTEON signal. Try this: • Check to make sure your LED Bulb is not connected to a dimmer. If so, remove the dimmer or relocate LED Bulb to a non-dimming fixture. • Try relocating your LED Bulb to see if linking can be accomplished.
Certifications and Warnings This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15B of the FCC Rules.
Product Warranty Limited Warranty Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or errors caused by misuse or neglect.