INSTEON® Wireless Thermostat Owner’s Manual 2732-232, 2441ZTH (US) 2732-432 (EU) 2732-532 (AUS/NZ) Page 1 of 27 Rev: 1/21/2014 8:36 AM
What’s in the Box? 3 INSTEON Wireless Thermostat Button Overview 4 INSTEON Wireless Thermostat Operation and Programming Mode Button Operation Energy Button Operation Set Button Operation Time/Sensor Button Operations Program Button Operation Fan and Hold Button Operations Master Button Operation 5 5 6 7 7 8 9 10 Optional Accessories Waterproof Temperature Sensor (2433A3) Power Supply 11 11 11 Installation Preparation Test Operation 11 11 12 Adding INSTEON Wireless Thermostat to an INSTEON Thermos
What’s in the Box? • • • INSTEON Wireless Thermostat Quick Start Guide Tabletop stand (removable for wall-mounting) Page 3 of 27 Rev: 1/21/2014 8:36 AM
INSTEON Wireless Thermostat Button Overview Temperature(s) of external sensor and/or wireless thermostat Current temperature Cool setpoint INSTEON Wireless Thermostat Programmed auto state Time 1 Humidity level Heat setpoint 2 Current thermostat mode: Off, Auto, Heat or Cool The gray buttons are under the INSTEON Thermostat door 9 8 7 6 5 4 3 1) Up/Down adjusts the temperature setpoint based on the current mode 2) Mode allows the user to select the current operational mode of the HVAC syste
INSTEON Wireless Thermostat Operation and Programming Mode Button Operation Off Mode: • No setpoints are shown • Up/Down arrows do not do anything Heat Mode: • Only Heat setpoint is shown • Up/Down arrows change Heat setpoint • Heat setpoint range: 35°-95°F (2°C-36°C) Cool Mode: • Only Cool setpoint is shown • Up/Down arrows change Cool setpoint • Cool setpoint range: 37°-97°F (4°C-38°C) Auto Mode: • Both Cool and Heat setpoints are shown • Up/Down arrows increase or decrease values by the same amount
• If you set Heat and Cool to the same temperature setpoint, Heat will automatically move down 2° (the minimum allowable gap). Energy Button Operation The Energy button (designated with the leaf) is a quick, efficient energy-saving option. When you press the Energy button, INSTEON Wireless Thermostat will adjust the Heat and Cool setpoints by a specified value. The default value is 4° from the current setting, but can be changed via home control software such as HouseLinc.
From Programmed Auto Mode: • Both Heat and Cool setpoints changed as specified • Default setback is 4° • Notice that ”Heating” is active on the left, but not on the right since the setpoint is lower than the current temperature; the element reads “Heat” Note: Onscreen text displaying “Heat” changes to “Heating” and “Cool” changes to “Cooling” to indicate HVAC system is active. Set Button Operation The Set button adds and removes INSTEON Wireless Thermostat from INSTEON scenes.
Third press of Time/Sensor: Clock Format setting (12- or 24-Hour clock) • Entire time line blinks • Up/Down arrows cycle between 12- and 24-hour clock format Note: AM/PM is not displayed when in 24-hour format. Program Button Operation • • • The Program button allows you to set up the various preprogrammed modes (Wake, Leave, Return and Sleep). Go to the next step by pressing Program again. Exit Program setup by: - Letting it time out after 4 minutes.
Note: The start of one program mode is also the end of the previous program mode. Third press of Program: Cool setpoint • Up/Down arrows cycle through temperature • Press and hold scrolls through temperatures Fourth press of Program: Heat setpoint • Up/Down arrows cycle through temperature • Press and hold scrolls through temperatures Fifth press of Program: Restarts the process to program another Mode/Day. NOTE: The four modes come preprogrammed.
Hold button operations • The Hold button is only functional in Auto Program mode • The Hold button overrides a preprogrammed mode until Hold is turned off IMPORTANT: • While Hold is enabled, the next preprogrammed time that comes in Preprogrammed Auto Mode will be ignored. • While Hold is enabled, the preprogrammed time notations are not shown (i.e. Wake, Leave, Return and Sleep). • Hold can be remotely enabled/disabled from an INSTEON controller.
Optional Accessories Waterproof Temperature Sensor (2433A3) INSTEON Waterproof Temperature Sensor is an external sensor that wires to your INSTEON Wireless Thermostat. When connected, the thermostat’s LCD display will show the sensor readings in small digits above the thermostat’s temperature. Waterproof Temperature Sensor can be extended up to 100’ with 22 AWG wire. It’s ideal for monitoring and maintaining constant temperatures in environments like pools, spas, aquariums and ponds.
- After a few seconds INSTEON Wireless Thermostat will display ambient temperature and humidity - Mode will default to OFF - Battery segment should show full with fresh batteries - Time will become active and show 12:00PM (default) 4) Snap INSTEON Wireless Thermostat into the supplied tabletop stand or mount safely to a wall Test Operation INSTEON Wireless Thermostat does not directly control the HVAC system.
INSTEON Thermostat will beep, then double-beep INSTEON Wireless Thermostat will double-beep 3) Test the scene by pressing and holding INSTEON Wireless Thermostat’s Master button. - When properly synchronized, pressing the Master button on one INSTEON Wireless Thermostat will illuminate the “Master” segment on that same screen. Additionally, the present room temperature of the Wireless Thermostat will be displayed in position 1 as temperature segments at the display’s top center.
Upon entering Scene mode this screen will display for ~2 seconds LCD display if Up button is tapped LCD displays when using Up or Down buttons to select from among the 4 controller groups Remove INSTEON Wireless Thermostat as a Controller If you want to remove INSTEON Wireless Thermostat from a scene as a controller, follow instructions below. Whenever possible, use software for managing scene memberships.
• • • Group 2 - Heating mode change Group 3 - Dehumidifiation, high humidity setpoint Group 4 - Humidification, low humidity setpoint 4) Press and hold responder Set button INSTEON Wireless Thermostat will double-beep upon completion LED will turn off Upon entering Add a Scene mode Upon entering Remove a Scene mode (defaults to Cooling mode) LCD displays when using Up or Down buttons to select from among the 4 controller groups User Setup Mode Overview IMPORTANT! Once you have added INSTEON Wireless Th
battery-saving mode to retrieve any updates from INSTEON Thermostat.
• Press Mode to step between menu items (sub-mode number will appear on top of the screen).
• Sub-mode 05: Chose whether the Internal or External temperature sensor initiates commands (Internal default) a. Up arrow = External b. Down arrow = Internal c. Note that when using two INSTEON Wireless Thermostats with External temperature sensor enabled, each INSTEON Wireless Thermostat will only display its local reading and the INSTEON Thermostat’s reading. (INSTEON Thermostat will display both INSTEON Wireless Thermostats’ readings.
temperature calibration modes (E) Internal Temperature Calibration • I appears on right side of screen • The top left number (77 in example) is the current reading according to the temperature sensor • The top right number (14 in example) is the current offset (represents 1.4) • These numbers can change while this screen is displayed even though the primary temperature does not change; they are floating point calculations.
2) Press Program to exit calibration mode Advanced 2-Stage Heating or Cooling Systems INSTEON Wireless Thermostat does not have the ability to operate first or second stages of Heat or Cool directly but can instruct INSTEON Thermostat to operate the HVAC.
4) When blinking/beeping stops, release Set button Device goes into factory reset for ~10 seconds and will perform a series of self tests Device will return to normal operations and display screen returns to normal 5) If INSTEON Wireless Thermostat displays a two-digit error code instead of the ambient temperature, remove batteries, wait a few seconds, then reinstall If problem persists, call INSTEON Support Line at 800-762-7845 Factory Reset Option 2 1) Press and hold INSTEON Wireless Thermostat Set button
LED Dual-color, blinks red or green during setup LED brightness N/A Local control Yes Commands supported as controller On Commands supported as responder N/A Software configurable Yes RF range Up to 150-Feet (50m) open air Phase bridge detect beacon No, RF-only device INSTEON device category 0x05 (all frequencies) INSTEON device subcategory Off 2441ZTH (915 MHz) 0x0A 2732-432 (869 MHz) 0x11 2732-532 (921 MHz) 0x12 X10 X10 address N/A X10 transmitter N/A X10 receiver N/A X10 s
Battery 2 AA cells (quality alkaline recommended) External Power Supply 4.5 to 7.
software of all changes, etc.). Use an AC adapter (sold separately) to power INSTEON Wireless Thermostat. The displayed temperature and humidity don’t seem accurate. When the Wireless thermostat is placed near the Wired Thermostat, the temperature and humidity readings are different. Both units were calibrated at the factory prior to shipment. Other factors could contribute to different readings.
Master Mode and check in for updates. If the two units can’t communicate, each will go out of the Mater mode after 30 to 60 minutes locations. The temperature setpoints and the Mode changes from what it was set to. The Wired Thermostat is the Master (or perhaps a different Wireless Thermostat) so the setpoint levels and mode changes (Heat, Cool, etc.) made at the Wired Thermostat (manually, following the Autoschedule, or via another INSTEON controller) are being sent to the Wireless for display.
Certification and Warranty FCC and Industry Canada Compliance Statement This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Português [Portuguese]: Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC. Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE. Norsk [Norwegian]: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.