Ballast Dimmer INSTEON® Remote Control 0-10VDC Ballast Dimmer Owner’s Manual 2475DA2 (US) 2442-422 (EU) 2442-522 (AUS/NZ) Page 1 of 16 2475DA2, 2442-422, 2442-522 Rev: 1/21/2014 8:31 AM
About Ballast Dimmer................................................................................................................................. 3 Features and Benefits................................................................................................................................. 3 Optional Accessories ................................................................................................................................. 3 Getting Started ......................................
About Ballast Dimmer This in-line ballast control module supports two different operational modes: dimmer and dual-relay. For use in new construction or retrofit (inside or outside the fixture) where saving energy is a priority.
Getting Started Map out the wall switch and load that you are going to remotely operate. Keep in mind that you are going to replace the existing wall switch with a keypad or another INSTEON controller where both are wired to the same constant hot line using the existing wiring. Installing Ballast Dimmer CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference.
Install Ballast Dimmer for Dimmable Ballast Note: use with branch circuit breakers 15 Amperes or fewer. 1) Write down the INSTEON ID found on the front of the unit (XX.XX.XX) 2) Turn off breaker/fuse and verify that the power is off 3) Disconnect wires from existing switch 4) Connect wires per diagram.
Installing Ballast Dimmer in Dual-Relay Mode 1) 2) 3) 4) 5) 6) 7) 8) Write down the INTEON ID found on the front of the unit (XX.XX.XX) Turn off breaker/fuse and verify that the power is off Disconnect wires from existing switch Connect the wires per diagram At the ballast location, disconnect the wires from the fixture you will be controlling and ensure that you have ½ inch of bare wire on the ends See the diagram to identify and connect the line, load 1, load 2 and neutral wires on Ballast Dimmer.
INSTEON Setup Some products have subtle differences in their setup procedures. Please refer to the other devices’ owner’s manuals for details. INSTEON Controllers, Responders and Links Let’s define a few terms. • The INSTEON “transmitter” is called a controller • The INSTEON “receiver” is called a responder • The association between the controller and responder is called a link Link Responder Controller Please note that a link is one way.
Changing Operating Modes (Dimmer or Switch) Relay Mode: By default, the Ballast Dimmer comes in Dimmer mode. Use the Relay mode for use with non-dimmable ballasts. Ballast Dimmer provides two relays to control individual ballasts or a multi-state ballast light fixture. In the multi-state ballast light fixture, either half could be off or on allowing brightness at 0%, 50%, and 100%.
X10 Setup Ballast Dimmer ships with no X10 address assigned. Add X10 Address 1) Press and hold set button until it beeps LED will start blinking green 2) Send the desired X10 address (plus on if desired) 3 times (e.g.
Remove Ballast Dimmer as a Controller If you no longer want Ballast Dimmer to control another device (or are removing Ballast Dimmer) it is important that you follow the instructions below for each responder.
Specifications General Product Name Ballast Dimmer Relay – INSTEON Remote Control Ballast Dimmer On/Off Switch (Dual-Band) Brand INSTEON 2475DA2 (US) Manufacturer Product Number 2446-422 (EU) 2446-522 (AUS/NZ) 813922011425 (US) UPC 813922012897 (EU) 813922012903 (AZ) Patent Number 7,345,998 US, International Patents Granted and Pending Warranty 2 Years, Limited INSTEON INSTEON ID 1 INSTEON 400 responder groups and 1 controller group Maximum Scene Memberships 400 (Combined Controller + Respo
Mechanical Set Button Behind switch or outlet, or above light fixture in a single-gang electrical box Analog + 0-10V Control (Gray wire) Analog - 0-10V Control (purple wire) Line Neutral Load 1 Load 2 1 Beeper Yes Beep on button press Optional (off by default) LED 1, green/red Mounting Wires Dimensions 171mm (wide), 30mm (high), 35mm (deep) 6.75-in. (wide), 1.2-in. (high), 1.4-in. (deep) Weight 5.
FCC 15.107, 15.109, 15.249 RSS 210 EN 300 220-2, 301 489-3 Certifications AS/NZS 4268, CISPR 22 UL 508 CSA C22.
Troubleshooting Problem The Status LED on Ballast Dimmer is not turning on and won’t control the load. Possible Cause Solution Make sure the circuit breaker(s) are turned on. Ballast Dimmer may not be getting power. Check the junction box wires to ensure all connections are tight and no bare wires are exposed. The Controller might have been reset without removing Ballast Dimmer from the scene. Re-add Ballast Dimmer to the Controller scene. The INSTEON signal may be too weak.
see if your devices are within communication range. You will need at least one other INSTEON dual-band device installed.
state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home. In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including without limitation damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of such damages.
