Additional Manual INSYS GSM 4.2 easy .
Copyright © January 07 INSYS MICROELECTRONICS GmbH Any duplication of this additional manual is prohibited. All rights on this documentation and the devices are with INSYS MICROELECTRONICS GmbH Regensburg. Restrictions of guarantee This additional manual contains a concise description. The compilation of the text has been made with the utmost care. Despite all efforts, there may be deviations compared with the actual functions. No guarantee can therefore be given for the accuracy of the contents.
Contents 4 INSYS GSM 4.2 easy 1 SCOPE OF DELIVERY....................................................7 2 GENERAL.....................................................................8 2.1 POSSIBLE USES FOR INSYS GSM 4.2 EASY ....................................8 2.1.1 2.1.2 Remote control via mobile phone or data connection ......................9 Remote programming via data connection .......................................9 2.2 POSSIBILITIES WITH THE PRECEDING VERSION INSYS GSM...............
INSYS GSM 4.2 easy Contents 4.3 TROUBLESHOOTING..................................................................25 4.3.1 4.3.2 4.3.3 4.3.4 No response on commands ..............................................................25 No connection established ...............................................................25 Alarm SMS is not dispatched ............................................................25 Signal Quality.................................................................................
Contents 6 INSYS GSM 4.2 easy 5.7.1 GSM Connection ...............................................................................31 5.7.1.1 5.7.1.2 5.7.1.3 5.7.1.4 5.7.1.5 5.7.1.6 PIN........................................................................................................................ 31 Service Center Number........................................................................................ 31 Automatic SMS processing.............................................................
INSYS GSM 4.2 easy 1 Scope of Delivery Scope of Delivery Please check the scope of delivery before initial operation: ¾ ¾ ¾ ¾ ¾ INSYS GSM 4.2 easy PC connection cable 9/9 pin (RS232) User manual INSYS GSM 4.2 Additional manual INSYS GSM 4.2 easy CD-ROM In case the content is not complete, please contact your supplier. Please check the device for shipping damage. Please also refer to your supplier if damage exists. Please keep the packaging material for dispatch or storage.
General INSYS GSM 4.2 easy 2 General The INSYS GSM 4.2 easy offers the same technical characteristics and functionalities as the standard version. The display of technical data and function descriptions of the standard version will be omitted in this manual (if possible). We refer to the user manual INSYS GSM 4.2. If the INSYS GSM 4.2 easy behaves differently than the standard version, we will mention this fact in the according passages.
INSYS GSM 4.2 easy General The fault message can be sent in the following format: ¾ Via SMS to a mobile phone ¾ Via SMS to a fixed network telephone (depending on the provider) ¾ Via SMS to a FAX device (depending on the provider) ¾ Via SMS to an E-mail recipient (depending on the provider) 2.1.
General INSYS GSM 4.2 easy 2.3 Restrictions/Notes The INSYS GSM 4.2 easy is connected to the Moeller easy device via a serial interface. Therefore, a memory can not be used at the same time. The password protection of the easy device may not be activated. If it is activated, no communication between INSYS GSM 4.2 and the compact controller is possible. However, the INSYS GSM 4.
INSYS GSM 4.2 easy 3 Function Descriptions 3.1 Definitions 3.1.1 Objects, instances, object short names Function Descriptions Programming of the Moeller easy takes place via objects. A digital input, a register, a counter for operating hours, a comparator, etc. are all examples for objects. Each object has an object short name. The digital register, for example, has the object short name "M", the analogue output has the short name "QA".
Function Descriptions INSYS GSM 4.2 easy If a change of a monitored value is registered, the sending of a fault message is prompted (SMS, SMS to fax, SMS to e-mail, SMS to fixed network). For digital values, the following events (adjustable) can cause the sending of a fault message: ¾ Change to 0 ¾ Change to 1 ¾ Any change For analogue values, an upper and a lower limit must be defined.
INSYS GSM 4.2 easy Function Descriptions Timing The shortest polling cycle is 1 second, i.e. signals shorter than 1 second will generally not be recognized. The object instances are not automatically queried if the INSYS GSM 4.2 easy is busy with the following actions: ¾ Field strength query and login state query, duration approx. 5s, interval 60s, may be switched off. ¾ SMS input buffer and processing of SMS, duration approx. 5s, interval 60s, may be switched off.
Function Descriptions 3.2.2 INSYS GSM 4.2 easy Periodic SMS In addition to the monitoring of values, it is also possible to periodically query the current condition or value of an object instance and to send it automatically via SMS. A periodic SMS can be sent in hourly intervals of 1 to 255 h. After this time has expired, the set object instance is read out and the value is sent as SMS. The query of the object instance is performed up to three times, if necessary.
INSYS GSM 4.2 easy Function Descriptions 3.3 Query and Controlling via SMS 3.3.1 SMS commands Many of the INSYS GSM 4.2 easy instances can be configured via SMS (the function automatic SMS processing must be activated). It is furthermore possible to access the inputs and outputs of the INSYS GSM 4.2 easy indirectly via registers. For the INSYS GSM 4.2 easy it is also possible to query various information regarding the state of the easy device via SMS, or the control program that is running on it.
Function Descriptions INSYS GSM 4.2 easy Monitoring of an object instance Command: MONITOR ,CN:[ Callback] Or: MONITOR ,CN:[ Callback] A reply with the value of the object instance or the alias follows. The query of the object instances is performed up to three times, if necessary. If there is still no reply from the easy device, an SMS with the text "NO SUCCESS" is sent instead of the SMS with the current value.
INSYS GSM 4.2 easy Function Descriptions Valid objects for the easy 800/MFD: Object Digital inputs Extended digital inputs Digital outputs Extended digital outputs Digital registers Analogue byte register Analogue word register Analogue double word register Analogue inputs Analogue outputs Diagnosis bits LEDs Current program cycle time Time Object short name I R Q S M MB MW MD IA QA D L Z U Example 1: Query of the object instance M12 MONITOR M12,CN: In this case, an SMS is sent to the INSYS GSM 4.
Function Descriptions 3.3.2 INSYS GSM 4.2 easy Setting an object instance Command: SET =[,CN:[ Callback]] Or: SET =[,CN:[ Callback]] The object instance is set to the according value. If callback is desired, the reply will contain "SUCCESS” for a successful setting procedure or “NO SUCCESS” for a failed setting procedure. The specification of “CN:” is optional.
INSYS GSM 4.2 easy Function Descriptions E.g. it is not recommended to switch objects like digital inputs directly. On the other hand it is uncritical to set a parallel connected bit register to simulate the setting of digital input within the configuration program (e.g. imitate the triggering of a sensor). 3.3.3 Status query Command: STATUS?,CN:[ Callback] This reply indicates the status of the easy device. The query of the status is performed up to three times, if necessary.
Function Descriptions 3.4 INSYS GSM 4.2 easy New History Entries The description of the history functionality of the INSYS GSM 4.2 easy can be found in the supplied manual INSYS GSM 4.2. Due to the extended functionality of the INSYS GSM 4.2, there are several additional entries in the history memory: Cause Detail PLC ERROR SYSTEM 20 PLC PERIODIC PLC PARM PLC CHANGE Meaning When communicating with the easy device, there was no response after 3 attempts. The process “Periodic SMS” starts.
INSYS GSM 4.2 easy Initial Operation 4 Initial Operation 4.1 Installation Overview 4.1.1 Installation for configuration The serial interface (RS 232) of the INSYS GSM 4.2 easy and the configuration PC are connected for initial operation and configuration. The cable used for the RS232 is the default supplied 9-pin cable with 9–pin D-SUB plug / 9-pin D-SUB jack. 4.1.2 Installation for the operation with Moeller easy For the operation with the Moeller easy, the 11.8-inch INSYS adapter cable is used.
Initial Operation 4.2 INSYS GSM 4.2 easy Initial Operation The easiest way to perform the initial operation is to use the configuration software HSComm GSM easy in Windows. Carry out the following steps: 1. Have the SIM card and PIN number ready, but do not insert the card yet. 2. Connect the INSYS GSM 4.2 easy and the PC with a serial cable (male/female). Connect the GSM antenna. 3. Connect the power supply to the terminals 10 … 60 VDC and the minus pole to GND. Switch the device on. 4.
INSYS GSM 4.2 easy Initial Operation 6. Select the following standard setting for the serial interface in the menu Interface at the configuration PC: If the INSYS GSM 4.2 easy is in an undefined state (e.g. due to a previous configuration), reset it to the factory settings (button Send default settings), if required. If the INSYS GSM 4.2 does not respond to the transmission of commands, select the button Synchronize RS232 to automatically adapt the baud rate and the data format. 7.
Initial Operation INSYS GSM 4.2 easy 8. Disconnect the power supply. 9. Press the sunken yellow button (see image) above the SIM card slot and remove the cardholder. Put the SIM card into the cardholder and reinsert it. The contacts of the SIM card face to the left when inserting. 10. Connect the power supply. 11.
INSYS GSM 4.2 easy 4.3 Troubleshooting 4.3.1 No response on commands Initial Operation INSYS GSM 4.2 easy and the terminal device (configuration PC or controller) have to operate the serial interface with the same baud rate and the same data format.(Default: 19.200 bps, 8N1) The INSYS GSM 4.2 easy can be reset to the factory settings by pressing the Reset key for an extended period (> 25 seconds). 4.3.2 No connection established Check the signal quality of th GSM network. Has the INSYS GSM 4.
Initial Operation INSYS GSM 4.2 easy The signal quality is indicated with an update interval of 1 minute (in idle state) by the LED Signal: LED Signal Response of AT**SIGNAL? Always on 25 ... 31 60 ms 23 ... 24 140 ms 21 ... 22 260 ms 19 ... 20 380 ms 17 ... 18 500 ms 15 ... 16 1000 ms 13 ... 14 Always off 0 ... 12 99 4.
INSYS GSM 4.2 easy Configuration with the Software HSComm easy 5 Configuration with the Software HSComm easy 5.1 General The software HSComm easy is used to configure the INSYS GSM 4.2 easy in Windows, without the need for explicit knowledge of the AT commands and their parameters. The settings are only sent to or read from the INSYS GSM 4.2 easy after the according instruction (buttons Send settings or Read settings).
Configuration with the Software HSComm easy INSYS GSM 4.2 easy 5.3.3 Program settings A small window is displayed which offers the selection of two options: Use "Automatic detection at program start" to attempt to establish a connection with the INSYS GSM 4.2 immediately after the start procedure. Use the item "Extended logging” to log all INSYS GSM 4.2 easy messages. The log can be viewed at the menu item "Send/receive log". 5.3.4 Terminal This terminal enables you to control the INSYS GSM 4.
INSYS GSM 4.2 easy 5.4 Configuration with the Software HSComm easy Status Bar The status bar at the lower window border of the HSComm displays the setting and activities of the serial interface. RX, TX light up synchronously when receiving, and sending data. 5.5 Buttons 5.5.1 Send settings The current settings in the HSComm are transferred to the INSYS GSM 4.2 easy. The settings in the PLC window are only transferred by clicking the button Send SPS configuration. 5.5.
Configuration with the Software HSComm easy 5.6 INSYS GSM 4.2 easy Tabs The settings of the basic and extended settings are spread across several pages, which can be selected via the tab titles. The settings are transmitted to the INSYS GSM 4.2 easy only after pressing the button Send values. The functions are described in the following chapters, provided they are are relevant for the easy version.
INSYS GSM 4.2 easy 5.7.1 Configuration with the Software HSComm easy GSM Connection 5.7.1.1 PIN The INSYS GSM 4.2 easy can store the SIM card PIN internally and automatically logs into the GSM network after being switched on. To enter, activate New PIN and enter the PIN. Instead of the digits, only * are displayed. The default setting is “0000”. When the INSYS GSM 4.2 easy has a stored PIN, the option PIN active is checked. A PIN stored in the INSYS GSM 4.2 easy is deleted by Delete PIN.
Configuration with the Software HSComm easy INSYS GSM 4.2 easy 5.7.1.4 SMS storage locations The number of available SMS storage locations on the SIM card is read out by the button ‘Locate SIM SMS storage locations now’. The controller queries the SMS storage locations in intervals of one minute. The baud rate and the number of SMS storage locations to be configured determine the duration of the query.
INSYS GSM 4.2 easy 5.7.2 Configuration with the Software HSComm easy System monitoring 5.7.2.1 Scheduled logout/login Log the INSYS GSM 4.2 easy in and out for a short period every day to allow maintenance functions of the GSM provider. Enter the logout time and the duration (1 to 98 minutes). The INSYS GSM 4.2 easy logs in into the GSM network again afterwards, if the PIN of the SIM card is stored. 5.7.2.
Configuration with the Software HSComm easy 5.8 INSYS GSM 4.2 easy Moeller easy™ Settings Use the tab “easy” to enter the compact controller Moeller easy™ settings. You need to indicate which Moeller easy™ compact controllers are installed. Now the buttons “Configure” are available. The following functions can be configured: ¾ Alias ¾ Monitoring ¾ Periodic SMS Depending on the selected compact controller, the speed of the serial interface is set to 4800 bps or 9600 bps.
INSYS GSM 4.2 easy Configuration with the Software HSComm easy These three buttons will enable you to read, write or delete the INSYS GSM 4.2 easy configuration for the Moeller easy™ functionality in particular. Reading and writing using these buttons will be faster than the total transfer via the button Send values, because the standard functionality need not be transferred once more. 5.8.
Configuration with the Software HSComm easy 5.8.2 INSYS GSM 4.2 easy Configure monitoring Clicking the button “Configure” displays the special configuration of the function. The table is not used to enter data, but to visualize the configuration. The entry takes place below the table. Selecting the monitoring line in the configuration window is done either with the selection box “No.” or by double-clicking the according line in the alias table.
INSYS GSM 4.2 easy 5.8.3 Configuration with the Software HSComm easy Configure periodic SMS Clicking the button “Configure” displays the special configuration of the function. The displayed settings below are only effective when “Periodic SMS” is turned on in the main window! In the text field “Alias” an object instance which has already been allocated an alias can be selected optionally. If this is not preferred or if no alias is defined yet, “Manual entry” must be selected.
Remote Configuration with EASY-SOFT and INSYS Connect 6 INSYS GSM 4.2 easy Remote Configuration with EASY-SOFT and INSYS Connect In the supplied software EASY-SOFT by Moeller, no functionality is designed for remote configuration. The INSYS GSM 4.2 easy therefore includes the program “INSYS Connect”, which initiates the connection setup to a remote INSYS GSM 4.2 easy. A compact controller Moeller easy is connected to this device. For the connection setup, a communication device (e.g.
INSYS GSM 4.2 easy Remote Configuration with EASY-SOFT and INSYS Connect Please note: To perform the remote configuration, the waiting period in EASY-SOFT must be adjusted. Otherwise, EASY-SOFT doesn’t wait long enough for the response of the addressed easy device. This device is not located at the local serial port, but the communication takes place via the GSM network. The response times are delayed due to the transmission link.
