AV Controller DHC-9.
Thank you for purchasing an Integra AV controller. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV controller. Please retain this manual for future reference. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer from whom you purchased this unit. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water.
Supplied Accessories Make sure you have the following accessories: Remote controller and three batteries (AA/R6) Speaker setup microphone Indoor FM antenna AM loop antenna Power cord (Power cord varies from country to country.) * 4 In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color.
Contents Introduction Supplied Accessories .......................................... 4 Features ................................................................. 6 Multiroom Capability ............................................ 8 Front & Rear Panels ............................................. 9 Front Panel ................................................................... 9 Display .......................................................................11 Rear Panel ....................................
Features Processing • HDMI Audio and Video Processing (Deep Color, x.v.
Features—Continued THX Ultra2 Plus Before any home theater component can be THX Ultra2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Ultra2 Plus logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come.
Multiroom Capability You can use three speaker systems with this AV controller—a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it, and another stereo speaker system in a third room that we call Zone 3. And, you can select a different audio source for each room. Main Room: In your main listening room, you can enjoy up to 7.1-channel playback (see pages 21–25).
Front & Rear Panels Front Panel North American model 1 2 34 bq br bs bt 5 7 8 9 bk bl bm bn bo 6 ck cl cmcn bp co Other models 9 The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item. On/Standby button (45) Sets the AV controller to On or Standby.
Front & Rear Panels—Continued Stereo button (90) Selects the Stereo listening mode. Listening Mode [ ]/[ ] buttons (90) Select the Onkyo original listening modes. Display See “Display” on page 11. Dimmer (RT/PTY/TP) button (65, 73) This button is used to adjust the display brightness. Other models, this is the [RT/PTY/TP] button, and it’s for RDS (Radio Data System). See “Using RDS” on page 72. Memory button (69) Used when storing or deleting radio presets.
Front & Rear Panels—Continued Display 1 2 5 3 6 7 8 9 4 bk For detailed information, see the pages in parentheses. Speaker/channel indicators (97) Indicate the speaker configuration and channels used by the current input source. Audyssey indicator (58) Flashes during automatic speaker setup. Lights up when the “Equalizer Settings” is set to “Audyssey”. : A box is displayed for each speaker that’s set in the Speaker Configuration. No box appears for speakers that are set to No or None.
Front & Rear Panels—Continued Rear Panel North American model 1 2 3 bt ck cl Other models 12 4 5 6 cm cn co 78 cp cq 9 crcs bk bl bo bp ct dk dl bm dm bn bq br dn bs do
Front & Rear Panels—Continued REMOTE CONTROL This (Remote Interactive) jack can be connected to the jack on another -capable Onkyo component for remote and system control. To use , you must make an analog audio connection (RCA) between the AV controller and the other component, even if they are connected digitally. RS232 This port is for connecting the AV controller to home automation equipment and external controllers. PHONO IN This audio input is for connecting a turntable.
Front & Rear Panels—Continued BALANCE L/R INPUT This balanced XLR input is for connecting a component with a stereo balanced XLR output. For a mono source, connect to the BALANCE L XLR. CD IN This analog audio input is for connecting a CD player’s analog audio output. TAPE IN/OUT These analog audio input and output jacks are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc. AUX 1 IN A VCR for playback only or other video source can be connected here.
Remote Controller Installing the Batteries 1 To open the battery compartment, press the small hollow and slide open the cover. Aiming the Remote Controller When using the remote controller, point it toward the AV controller’s remote control sensor, as shown below. Remote control sensor Standby indicator AV controller 30˚ 2 3 Insert the three supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. Slide the cover shut.
Remote Controller—Continued About the Remote Controller Modes As well as the AV controller, you can also use the remote controller to control your other AV components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the Remote Mode buttons. Receiver/Tape Mode Receiver/Tape mode is used to control the AV controller. It can also be used to control an Onkyo cassette recorder connected via .
Remote Controller—Continued For detailed information, see the pages in parentheses. Standby button (45) Sets the AV controller to Standby. Audio Sel button (129) Selects the audio input: analog, digital, HDMI, or multichannel. On button (45) Turns on the AV controller. ■ TAPE mode On twin cassette decks, only Deck B can be controlled. Input Selector buttons (64) Used to select the input source. 1 Previous and Next [ Macro buttons (141) Used with the Macro function.
Remote Controller—Continued Standby button Sets the DVD player to Standby. DVD Mode To set the remote controller to DVD mode, press the [DVD] Remote Mode button. Number buttons Used to enter title, chapter, and track numbers, and to enter times for locating specific points. 1 2 3 On Standby DVD VCR/DVR TV Top Menu button Selects a DVD’s top menu.
Remote Controller—Continued Standby button Sets the component to Standby. CD/CDR/MD Modes To control an Integra/Onkyo CD player, MD recorder, or CD recorder, or a CD or MD player/recorder made by another manufacturer, press the [CD] Remote Mode button to select the CD/CDR/MD remote controller mode. In order to control an Onkyo MD recorder or CD recorder, or a component made by another manufacturer, you must first enter the appropriate remote control code (see page 137).
Remote Controller—Continued Standby button Turns off the iPod. Dock Mode Dock mode is for controlling an Apple iPod in an Onkyo RI Dock. To control an RI Dock, press the [Dock] Remote Mode button to select the Dock remote controller mode. In order to control an RI Dock, you must first enter the appropriate remote control code (see page 137). On button* Turns on the iPod. Top Menu button Works as a Mode button when used with a DS-A2 RI Dock.
About Home Theater Enjoying Home Theater Thanks to the AV controller’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).
Connecting the AV Controller Connecting Your Speakers The AV controller is designed to be used with a separate multichannel power amplifier. You connect the AV controller’s PRE OUT jacks to the amplifier’s inputs, and connect your speakers to the amplifier’s speakers terminals. Speaker settings such as crossover frequency and distance are set on the AV controller. Speaker Configuration For 7.1-channel surround-sound playback, you need seven speakers and a powered subwoofer.
Connecting the AV Controller—Continued Connecting a Powered Subwoofer Using a suitable cable, connect the AV controller’s SUBWOOFER PRE OUT to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the SUBWOOFER PRE OUT to the amp’s input. You can also connect a powered subwoofer to the AV controller’s balanced SUBWOOFER PRE OUT XLR jack by using a balanced XLR cable.
Connecting the AV Controller—Continued Connecting a Power Amplifier with XLR Inputs You can connect the AV controller to a multichannel power amplifier with balanced XLR input jacks by using several XLR audio cables. The AV controller’s balanced PRE OUT XLR jacks are wired as shown. See your multichannel power amplifier’s instruction manual for more information on connecting speakers.
Connecting the AV Controller—Continued Bi-amping the Front Speakers The FRONT L/R and SURR BACK L/R outputs can be used with front speakers and surround back speakers, respectively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance. • When bi-amping is used, the AV controller is able to feed up to 5.1 speakers in the main room.
Connecting the AV Controller—Continued Connecting Antenna 2 This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. Use thumbtacks or something similar to fix the FM antenna into position. The AV controller won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Thumbtacks, etc.
Connecting the AV Controller—Continued ■ Using a TV/FM Antenna Splitter It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown. ■ Other Models Push Insert wire Release TV/FM antenna splitter To AV controller Once your AV controller is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.
Connecting the AV Controller—Continued AV Connection Color Coding About AV Connections RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs. • Before making any AV connections, read the manuals supplied with your other AV components.
Connecting the AV Controller—Continued Connecting Both Audio & Video By connecting both the audio and video outputs of your DVD player and other AV components to the AV controller, you can switch the audio and video signals simultaneously simply by changing the input source on the AV controller. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD player, etc. On Power On Of f Standby Seven Channel Amplifier RDA-7.
Connecting the AV Controller—Continued ■ “Monitor Out” Setting Set to “Analog” With the “Monitor Out” setting set to “Analog” (see page 49), video input signals flow through the AV controller as shown, with composite video and S-Video sources being upconverted for the component video output. Use this setting if you connect the AV controller’s COMPONENT VIDEO MONITOR OUT 1 or 2 to your TV. Composite video is upconverted to S-Video and S-Video is downconverted to composite video.
Connecting the AV Controller—Continued Connecting a TV or Projector See “Connecting Components with HDMI” on page 37 for HDMI connection information. Step 1: Video Connection Choose a video connection that matches your TV ( A , B , or C ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3.
Connecting the AV Controller—Continued Connecting a DVD player Step 1: Video Connection Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV controller to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection.
Connecting the AV Controller—Continued Hooking Up the Multichannel Input If your DVD player supports multichannel audio formats such as DVD-Audio and SACD, and it has a multichannel analog audio output, you can connect it to the AV controller’s multichannel input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV controller’s MULTI CH: FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player.
Connecting the AV Controller—Continued Connecting a VCR or DVD Recorder for Playback With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV controller, which is useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV controller to your TV with the same type of connection.
Connecting the AV Controller—Continued Connecting a VCR or DVD Recorder for Recording Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( A or B ), and then make the connection. The video source to be recorded must be connected to the AV controller via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your VCR or DVD recorder ( a or b ), and then make the connection.
Connecting the AV Controller—Continued Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV controller, which is useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches the video source ( A , B , or C ), and then make the connection.
Connecting the AV Controller—Continued Connecting Components with HDMI About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Connecting the AV Controller—Continued Making HDMI Connections Step 1: Use HDMI cables to connect the AV controller’s HDMI jacks to your HDMI-compatible Blu-ray player/DVD player, TV, projector, and so on. Step 2: Assign each HDMI IN to an input selector. See “Video Input Setup” on page 50. ■ Video Signals Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT MAIN and OUT SUB for display on your TV.
Connecting the AV Controller—Continued Connecting a Game Console Step 1: Video Connection Choose a video connection that matches your game console ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV controller to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection.
Connecting the AV Controller—Continued Connecting a Camcorder or Other Device Step 1: Video Connection Choose a video connection that matches your camcorder ( A or B ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your camcorder ( a or b ), and then make the connection. AUX 2 Input b Digital a AUX 2 Input L Audio R AUX 2 Input S Video AUX 2 Input Video A B VIDEO OUT S VIDEO OUT L AUDIO R OUT OPTICAL OUT Camcorder, etc.
Connecting the AV Controller—Continued Connecting a CD Player or Turntable ■ CD Player or Turntable (MM) with Built-in Phono Preamp Step 1: Choose a connection that matches your CD player ( a , b , or c ). Use connection a for a turntable with a built-in phono preamp.
Connecting the AV Controller—Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches your recorder ( a , b , c , or d ), and then make the connection. b c a IN COAXIAL IN 2 L (VCR/DVR) R TAPE OPTICAL a IN 2 (CD) L d R OPTICAL TAPE Connect one or the other Connection must be assigned (see page 53) L COAXIAL OUT OPTICAL OUT OPTICAL IN R AUDIO IN L R AUDIO OUT Cassette, CDR, MD, etc.
Connecting the AV Controller—Continued Connecting an RI Dock Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock’s instruction manual. ■ If Your iPod Doesn’t Support Video: Connect your RI Dock’s audio output jacks to the AV controller’s AUX 1 IN L/R jacks. (Onkyo DS-A2X hookup shown below.
Connecting the AV Controller—Continued Connecting Integra/Onkyo Components Step 1: Make sure that each Integra/Onkyo component is connected to the AV controller with an analog audio cable (RCA). Step 2: Make the necessary connections (see illustration below). Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 57).
Turning On the AV Controller Standby On/Standby Standby indicator On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner 7 8 TV On Input CD 9 D.
First Time Setup This section explains the settings that you need to make before using the AV controller for the very first time. Monitor Setup 1 Press the [HDMI Out] button. The current setting is displayed. 2 Press the [HDMI Out] button repeatedly to select: Analog: Select this if your TV is connected to a video output other than the HDMI OUT MAIN or HDMI OUT SUB. HDMI Main: Select this if your TV is connected to the HDMI OUT MAIN. HDMI Sub: Select this if your TV is connected to the HDMI OUT SUB.
First Time Setup—Continued In this Instruction Manual, illustrations from the onscreen menu or explanations referring to the menu will be in the same language as the Instruction Manual. The default Language setting for the onscreen menu is English. If your Instruction Manual is in a language other than English, first follow the instructions below to change the Language. Selecting the Language used for the onscreen setup menus 4 This setting determines the language used for the onscreen setup menus.
First Time Setup—Continued ■ Menus for First Time Setup Input Selector Macro 1 2 DVD VCR Zone3 3 Remote Mode Submenus Zone2 CD CDR/MD TV Cable Dock SAT Tape/AMP Sleep Dimmer 2 Top Men u Men 1 1. 2. 3. 4. 5. u + CH Enter Disc Album - 1 Receiver Prev CH Gu id Se e tu p p. 49 p. 54 VOL t Ex i Retu Display 1.
First Time Setup—Continued Monitor Out Setup 2 Enter On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner 7 8 Use the Up and Down [ ]/[ ] buttons to select “1. Input/Output Assign”, and then press [Enter]. The “Input/Output Assign” menu appears. TV Input CD 9 D.TUN Phono +10 Enter 0 TV VOL 1. 2. 3. 4. 5. 1.
First Time Setup—Continued 5 Enter Enter 6 Enter Enter 7 50 Se tu p Use the Up and Down [ ]/[ ] buttons to select “Resolution”, and use the Left and Right [ ]/[ ] buttons to select: Through: Select this to pass video through the AV controller at the same resolution and with no conversion. Auto: Select this to have the AV controller automatically convert video at resolutions not supported by your TV. (Not available when the “Monitor Out” setting is set to “Analog”.
First Time Setup—Continued 3 Enter Enter Use the Up and Down [ ]/[ ] buttons to select “2. HDMI Input”, and then press [Enter]. The “HDMI Input” menu appears. 1–2. HDMI Input DVD VCR/DVR CBL/SAT GAME/TV AUX1 AUX2 MOVE VALUE 1–2. HDMI Input TAPE TUNER CD PHONO MOVE 4 Enter Enter 5 VALUE ------------- page 49), and the “HDMI Input” setting must be set to “- - -”. See page 29 for more information on video signal flow and upconversion.
First Time Setup—Continued Component Video Setup 3 If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector. For example, if you connect your DVD player to COMPONENT VIDEO IN 3, you must assign COMPONENT VIDEO IN 3 to the DVD input selector. Enter By default, the DVD input selector is assigned to COMPONENT VIDEO IN 1, and all of the other input selectors are assigned to the “- - -” option.
First Time Setup—Continued Digital Audio Input Setup 4 If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the “CD” input selector. Enter Here are the default assignments.
First Time Setup—Continued 3 Analog Audio Input Setup Enter On Standby DVD VCR/DVR TV Use the Up and Down [ ]/[ ] buttons to select “5. Analog Audio Input”, and then press [Enter]. The “Analog Audio Input” menu appears. Input CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 DVD CD Stereo 9 D.TUN Phono +10 Enter 1–5.
First Time Setup—Continued Speaker Settings 3 4 5 Tape Tuner 7 8 - 6 CD If you change these settings, you must run the automatic speaker setup again (see page 58). 9 D.TUN Phono +10 0 TV VOL Enter Clear 11 --/--- 10 Input Selector Use the Up and Down [ ]/[ ] buttons to select “1. Speaker Settings”, and then press [Enter]. The “Speaker Settings” menu appears. 12 Macro 1 2 Zone3 3 2–1.
First Time Setup—Continued TV Format Setup (not North American models) 4 For the onscreen setup menus to display properly, you must specify the TV system used in your area. 1 Receiver Se tu p Enter Press the [Receiver] button, followed by the [Setup] button. The main menu appears onscreen. Enter If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 5 2 Enter Enter Use the Up and Down [ ]/[ ] buttons to select “6. Miscellaneous”, and then press [Enter].
First Time Setup—Continued AM Frequency Step Setup (on some models) 5 Se For AM tuning to work properly, you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. 1 Receiver Se tu p 2 Enter Enter Press the [Receiver] button, followed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV.
First Time Setup—Continued Automatic Speaker Setup (Audyssey MultEQ® XT) With the supplied calibrated microphone, Audyssey MultEQ XT automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position.
First Time Setup—Continued Using Audyssey MultEQ® XT The onscreen menus shown in this manual may be slightly different from what you see on your TV. 1 2, 11 On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 1 Turn on the AV controller and the connected TV. On the TV, select the input to which the AV controller is connected. 2 Place the speaker setup microphone at measurement point 1 (page 58), and connect it to the Setup Mic jack.
First Time Setup—Continued 3 Press [Enter]. The automatic speaker setup starts. 5 The following screen appears. Auto Speaker Setup Enter Auto Speaker Setup Next Do not unplug Setup Mic. Please keep quiet. Now measuring. . . 2 2 Please place microphone at next position at ear height. ENTER ENTER Test tones are played through each speaker as Audyssey MultEQ® XT Automatic Speaker Setup runs. This process takes a few minutes.
First Time Setup—Continued 8 When the measurements are complete, the following screen appears. Auto Speaker Setup 11 Disconnect the setup Mic. Auto Speaker Setup Please, unplug Setup Mic. Calculating... 9 When the calculations are complete, the following screen appears. Enter Auto Speaker Setup Notes: • When the automatic speaker setup is complete, the “Equalizer Settings” (page 110) will be set to Audyssey.
First Time Setup—Continued Error Messages Auto Speaker Setup While the automatic speaker setup is in progress, one of the following error messages may appear: Next Cancel ❑ Ambient noise is too high :Yes :--- Auto Speaker Setup :No ! MOVE Retry Cancel :Error Speaker Detect Error ! ENTER ENTER The surround back left speaker has not been detected. Auto Speaker Setup Ambient noise is too high.
First Time Setup—Continued Reviewing the Results Enter Changing the Speaker Settings Manually Use the Up and Down [ ]/[ ] buttons to select the settings that you want to review, and then press [Enter]. Auto Speaker Setup Enter Save Review SP Config Review SP Distance Review SP Level Cancel MOVE ENTER ENTER The options are: Review SP Config Review the speaker configuration settings.
Basic Operations Selecting the Input Source 3 On Standby DVD VCR/DVR TV Input CBL/SAT 1 2 3 + Game/TV AUX z AUX 2 TV CH 4 5 6 - Tape Tuner 7 8 1 CD 9 D.
Basic Operations—Continued This section explains functions that can be used with any input source. 4 5 Tape Tuner 7 8 - 6 +10 You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV controller is set to Standby. CD 9 D.
Basic Operations—Continued Using the Sleep Timer With the sleep timer, you can set the AV controller to turn off automatically after a specified period. Receiver Sleep Adjusting the Bass & Treble You can adjust the bass and treble for the front speakers, except when the Direct or THX listening mode is selected. Press the [Receiver] button, and then press the [Sleep] button repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps.
Listening to the Radio ■ Manual Tuning Mode Listening to AM/FM Stations Tuning Mode 1 Press the [Tuning Mode] button so that the AUTO indicator disappears from the display. 2 Press and hold the Tuning Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the button repeatedly to change the frequency one step at a time. Tuning Tuner With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection.
Listening to the Radio—Continued ■ Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH - Displaying AM/FM Radio Information Display TV Input Number buttons 4 5 6 Tape Tuner CD 7 8 9 D.TUN Phono +10 0 TV VOL D.
Listening to the Radio—Continued Presetting AM, FM, XM, and SIRIUS Stations 2, 4 Selecting Presets Preset On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner 7 8 3 TV Input CD 9 D.TUN Phono +10 0 TV VOL Clear 11 --/--- 10 Input Selector 12 Macro 1 2 DVD VCR TV Cable Zone3 3 Remote Mode Zone2 CD CDR/MD Dock SAT Top Tune into the AM, FM, XM, or SIRIUS station you want to store as a preset. 2 Press the [Memory] button.
Listening to the Radio—Continued AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 9 Game/TV Listening to HD Radio™ Stations (North American model only) AUX 1 D.TUN Phono HD Radio technology brings digital radio to conventional analog AM and FM radio stations, with improved sound quality, better reception, and new data services. HD Radio technology provides CD-quality sound for FM stations and FM-quality sound for AM stations.
Listening to the Radio—Continued Selecting Multicast Channels FM HD Radio stations can transmit multiple programs on the same frequency by using what are called multicast channels. If the current HD Radio station is broadcasting multicast channels, the SPS (secondary program services) indicator lights up. 1 Press [Enter]. The SPS indicator flashes.
Listening to the Radio—Continued RDS Program Types (PTY) Using RDS RDS only works in areas where RDS broadcasts are available. When tuned to an RDS station, the RDS indicator appears. RDS indicator Display None NONE News reports NEWS Current affairs AFFAIRS Information INFO Sport SPORT Education EDUCATE Drama DRAMA Culture CULTURE ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals.
Listening to the Radio—Continued Displaying Radio Text (RT) 3 Use the Preset [ ]/[ ] buttons to select the type of program you want. See the table on page 72. 4 To start the search, press [Enter]. The AV controller searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search. 5 When a station you want to listen to is found, press [Enter]. If no stations are found, the message “Not Found” appears.
Listening to the Radio—Continued Listening to XM Satellite Radio® (North American Model Only) About XM Radio XM is North America’s number one satellite radio company, offering an extraordinary variety of commercialfree music, plus the best in premier sports, news, talk radio, comedy, children’s and entertainment programming, broadcast in superior digital audio quality coast to coast. For more information, or to subscribe, U.S. customers visit xmradio.
Listening to the Radio—Continued --/--Input Selector 4 Macro 1 2 Zone3 3 Remote Mode DVD VCR TV Cable Zone2 CD CDR/MD Dock SAT Tape/AMP Sleep Dimmer To Receiver en pM Men u Enter CH Enter Disc Album Prev CH Enter u + Setup Receiver Gu id Se VOL t Ex i e tu p Retu rn Display Muting Playlist Rec Random Setting the Satellite Radio Mode Before you can listen to XM Satellite Radio, you must set the Satellite Radio mode to XM.
Listening to the Radio—Continued Signing Up for XM Satellite Radio Selecting XM Radio Channels Once you have installed the XM Mini-Tuner and Home Dock, you are ready to subscribe to XM Satellite Radio. You’ll need a major credit card and your XM Radio ID. There are three places you can find your 8-character XM Radio ID: 1. On the XM Mini-Tuner 2. On the XM Mini-Tuner packaging 3. On XM Channel 0, as explained below There are three ways to select XM radio channels: 1.
Listening to the Radio—Continued ■ Category Search Mode 1 Press the [Receiver] Remote Mode button, and then press the [Enter] button repeatedly to select Category Search mode. Remote controller Receiver This procedure can also be performed on the AV controller by using its [Tuner] button, and [Tuning Mode] button. Enter 2 Use the Left and Right [ ]/[ ] buttons to select a category, and use the Up and Down [ ]/[ ] buttons to select a channel in that category.
Listening to the Radio—Continued Displaying XM Radio Information 11 --/--- 10 Input Selector 12 Macro 1 2 Zone3 3 Remote Mode AV controller Press the [Display] button repeatedly to cycle through the available information.
Listening to the Radio—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “5. Satellite Radio”, and then press [Enter]. The “Satellite Radio” screen appears. The name of the currently selected input selector is displayed in a box. Enter 4 Position the XM Mini-Tuner Antenna so that as many bars as possible (up to 3) appear on the XM Satellite signal strength meter. The best signal is achieved when the antenna is pointing to the southern sky through an unobstructed window. 4–5.
Listening to the Radio—Continued Listening to SIRIUS Satellite Radio® (North American Models Only) Important SIRIUS Satellite Radio Information SIRIUS is available in the US for subscribers with addresses in the continental US and is available in Canada for subscribers with a Canadian address. To Get SIRIUS Satellite Radio a subscription and compatible tuner and antenna are required and sold separately. Visit sirius.com for the most complete and up-to-date channel lineup and information.
Listening to the Radio—Continued Positioning the Antenna For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to determine which area you are in and position the antenna accordingly. 2 Enter Use the Up and Down [ ]/[ ] buttons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears. SKY NORTH Enter 1 WEST 4 5 1. 2. 3. 4. 5. 6. 7.
Listening to the Radio—Continued Selecting SIRIUS Satellite Radio Channels Tuning There are three ways to select SIRIUS Satellite Radio channels: 1. Channel Search mode: select any channel. 2. Category Search mode: select channels by category. 3. Direct tuning: enter channel number. On Standby DVD VCR/DVR TV Input Number buttons Tuner CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner 7 8 Selecting SIRIUS Satellite Radio CD 9 D.
Listening to the Radio—Continued ■ Category Search Mode 1 Press the [Receiver] Remote Mode button, and then press the [Enter] button repeatedly to select Category Search mode. Remote controller Receiver Enter This procedure can also be performed on the AV controller by using its [Tuner] button, and [Tuning Mode] button. 2 Use the Left and Right [ ]/[ ] buttons to select a category, and use the Up and Down [ ]/[ ] buttons to select a channel in that category.
Listening to the Radio—Continued TV VOL D.TUN Phono +10 0 3 Clear 11 --/--- 10 Input Selector 12 Use the Up and Down [ ]/[ ] buttons to select “6. SIRIUS Parental Lock”, and then press [Enter]. The “SIRIUS Parental Lock” screen appears. Macro 1 2 Zone3 3 Remote Mode DVD VCR TV Cable Zone2 CD Enter CDR/MD Dock SAT Tape/AMP Sleep Dimmer To Receiver en pM u Men u + 4–6.
Listening to the Radio—Continued 6 Enter 7 Enter 8 Use the Up and Down [ ]/[ ] buttons to select a channel, and use the Left and Right [ ]/[ ] buttons to select Locked or Unlocked. The number, name, and status of the currently selected channel is displayed. Use the Up and Down [ ]/[ ] buttons to select “6. SIRIUS Parental Lock”, and then press [Enter]. The “SIRIUS Parental Lock” screen appears. Enter 4–6.
Listening to the Radio—Continued / Input Selector Macro 6 1 Press the [D.TUN] button, and then use the number buttons to enter the new 4-digit PIN number. D.TUN Clear 2 DVD VCR TV Cable SAT Top CBL/SAT 2 3 Game/TV AUX 1 AUX 2 4 5 6 Tape Tuner CD 7 8 9 D.TUN Clear 12 Use the Left and Right [ ]/[ ] buttons to select a number on the screen, and then press [Enter]. Repeat this for each of the four digits in the new PIN number. The Confirm screen appears.
Listening to the Radio—Continued +10 0 Clear 11 --/--- 10 Input Selector 3 12 Macro 1 2 DVD VCR TV Cable Zone3 3 Remote Mode Zone2 CD CDR/MD Dock SAT Tape/AMP Sleep Dimmer Top Receiver u Men Men u + Enter CH Enter Disc Album Prev CH VOL Enter - Setup Gu id Se e tu p t Ex i Retu Display rn Muting Playlist Rec Random Listening Mode Stereo Surround Positioning the SiriusConnect Home Antenna You can check the strength of the SIRIUS Satellite Radio signal and adju
Listening to the Radio—Continued SIRIUS Satellite Radio Messages The following messages may appear while using SIRIUS Satellite Radio. ❑ ACQUIRING The SiriusConnect receiver is acquiring the signal or no signal is present. Make sure the SiriusConnect Home tuner is connected properly and that there are no obstacles close by. ❑ ANTENNA ERROR Make sure the SiriusConnect Home tuner is connected properly. ❑ SUB UPDATED Displayed while your subscription is being updated.
Recording This section explains how to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded. • Various restrictions apply to digital recording. Refer to the manuals supplied with your digital recording equipment for more details.
Using the Listening Modes Selecting the Listening Modes Selecting with the Remote Controller For a description of each listening mode, see “About the Listening Modes” on page 97. Top Men CH - • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV controller with a digital audio connection (coaxial, optical, or HDMI). • While a pair of headphones is connected, you can only select the Mono, Direct, or Stereo listening mode.
Using the Listening Modes—Continued Listening Modes Available for Each Source Format Analog and PCM Sources Analog/PCM Source format Media Listening Mode Direct Stereo Mono Multichannel 32–96 kHz*1 CD, TV, radio, ✔ ✔ ✔ Neo:6 Neural THX Dolby PLII Movie/ Dolby PLIIx Movie*3 Dolby PLII Music/ Dolby PLIIx Music*3 Dolby PLII Game/ Dolby PLIIx Game*3 Dolby EX Neo:6 Cinema Neo:6 Music THX Cinema/Music/Games*5 Dolby PLII/Dolby PLIIx Movie + THX Cinema*5 Dolby PLII/Dolby PLIIx Music + THX Music*5 Dolby PLII/Do
Using the Listening Modes—Continued Dolby Digital, and Dolby Digital Plus Sources Source format Multichannel Media Mono/Multiplex ✔ ✔ ✔ ✔ ✔ ✔ Blu-ray, HD DVD ✔ ✔ ✔ ✔*3 Neural THX ✔ DolbyDigital ✔ Dolby EX Dolby PLII/Dolby PLIIx Music + THX Music*4 ✔ ✔ ✔ ✔ ✔*4 ✔*3 ✔ ✔*3 ✔ ✔*3 ✔ ✔*3 ✔ ✔ ✔*3 ✔ ✔ ✔*3 ✔ ✔ ✔ ✔ ✔ *3 ✔ ✔ ✔ *2 ✔*3 ✔*2 ✔*3 ✔*2 ✔*3 ✔*2 Dolby PLII/Dolby PLIIx Game + THX Games*4 Neo:6 Cinema/Music + THX Cinema/Music*4 ✔*2 ✔*2 ✔ ✔ Neo:6 + THX Cinema/Music/G
Using the Listening Modes—Continued DTS Sources ✔: Available Listening Modes Source format DTS, DTS96/24 Multichannel Media 2ch Mono DVD, CD, etc. Listening Mode DTS-ES Discrete/Matrix DVD, CD, etc.
Using the Listening Modes—Continued TrueHD Sources ✔: Available Listening Modes Source format TrueHD Multichannel Media 2ch TrueHD 192kHz Mono/Multiplex Multichannel Blu-ray, HD DVD Listening Mode 2ch Blu-ray, HD DVD Direct ✔ ✔ ✔ ✔ ✔ Stereo ✔ ✔ ✔ ✔ ✔ Mono ✔ ✔ ✔ TrueHD ✔ ✔ Neo:6 ✔*2 Neural THX ✔*4 ✔*3*4 Dolby PLII Movie/ Dolby PLIIx Movie*1 ✔*2 ✔ Dolby PLII Music/ Dolby PLIIx Music*1 ✔*2 ✔ Dolby PLII Game/ Dolby PLIIx Game*1 Dolby EX ✔ ✔*2 ✔ Neo:6 Cinema ✔ Neo:6 Mus
Using the Listening Modes—Continued DTS-HD Sources Source format DTS-HD High Resolution Multi 2ch Mono channel DTS-HD Master Audio Multi 2ch Mono channel ✔: Available Listening Modes DTS-HD Master Audio 192kHz Multi 2ch Mono channel Blu-ray, HD DVD Blu-ray, HD DVD Blu-ray, HD DVD Media Listening Mode Direct Stereo Mono DTS-HD High Resolution DTS-HD Master Audio ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔*2 Neural THX ✔*2 ✔*4 ✔*3*4 ✔*4 ✔*3*4 Dolby PLII Movie/ Dolby PLIIx Movie*1 Dolby
Using the Listening Modes—Continued DTS Express and DSD Sources ✔: Available Listening Modes DSD*1 DTS Express Source format Multichannel Media Listening Mode Direct Stereo Mono DTS Express DSD 2ch Mono Multichannel (3/2.
Using the Listening Modes—Continued About the Listening Modes The AV controller’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. The Listening Mode button illustration shows that listening modes can be selected. The Listening Mode button illustration shows the remote controller buttons. See “Selecting the Listening Modes” on page 90 for information on the use of the Listening Mode buttons.
Using the Listening Modes—Continued Dolby TrueHD Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc formats, this new Dolby format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate. For the signals supported by the AV controller, see page 94. 5.1-channel source + Dolby PLIIx Music These modes use the Dolby Pro Logic IIx Music mode to expand 5.1-channel sources for 6.1/7.1-channel playback.
Using the Listening Modes—Continued Neural THX 5.1/7.1 Neural-THX Surround employs psychoacoustic frequency domain processing, which allows delivery of a more detailed sound stage, with superior channel separation and localization of audio elements. The Neural THX 5.1 and Neural THX 7.1 modes can expand any 2-channel stereo source for 5.1- or 7.1-channel playback, respectively. Use them with CD, radio, cassette, TV, VHS, DVD, and other 2-channel stereo sources, including video games.
Using the Listening Modes—Continued Onkyo Original DSP Modes Mono Movie This mode is suitable for old movies and other mono sources. The center speaker outputs the sound as it is, while reverb is applied to the sound output by the other speakers, giving presence to even mono material. Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.
Advanced Setup The onscreen setup menus appear on the connected TV and provide a convenient way to change the AV controller’s various settings. Settings are organized into eight categories on the main menu, most containing a submenu. The onscreen menus shown in this manual may be slightly different from what you see on your TV. MENU 1. Input/Output Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8.
Advanced Setup—Continued Monitor Out Setup 3 This section explains items on the “Input/Output Assign” menu. Enter On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 TV Enter Input AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 9 D.
Advanced Setup—Continued Monitor Out Resolution You can specify the output resolution for the HDMI outputs and have the AV controller upconvert the picture resolution as necessary to match the resolution supported by your TV. Through: Select this to pass video through the AV controller at the same resolution and with no conversion (default). Auto: Select this to have the AV controller automatically convert video at resolutions not supported by your TV.
Advanced Setup—Continued Speaker Setup 1 This section explains items on the “Speaker Setup” menu. Receiver Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 58). Tape Tuner 7 8 tu p CD 9 D.TUN Phono +10 Se 0 Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV.
Advanced Setup—Continued 4 Enter Use the Up and Down [ ]/[ ] buttons to select “Subwoofer”, and then use the Left and Right [ ]/[ ] buttons to select: Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected. 8 Enter Enter 5 Enter Enter Use the Up and Down [ ]/[ ] buttons to select “Front”, and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency. Note: Fixed at “Full Band” if “Subwoofer” (step 4) is set to “No”.
Advanced Setup—Continued Low-Pass Filter for the LFE Channel Double Bass This setting is not set automatically by the Automatic Speaker Setup function (see page 58). This setting is not set automatically by the Automatic Speaker Setup function (see page 58). With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
Advanced Setup—Continued Speaker Distance 4 These settings are set automatically by the Automatic Speaker Setup function (see page 58). Enter With the “Speaker Distance” settings, you can specify the distance from each speaker to the listening position. Tape Tuner 7 8 CD 9 TV VOL D.TUN Phono +10 0 Enter Clear 11 --/--- 10 Input Selector 12 Macro 1 2 DVD VCR Zone3 3 Remote Mode Use the Up and Down [ ]/[ ] buttons to select “3. Speaker Distance”, and then press [Enter].
Advanced Setup—Continued 6 Enter Enter 7 Use the Up and Down [ ]/[ ] buttons to select a speaker, and use the Left and Right [ ]/[ ] buttons to specify the distance. Specify the distance from the speaker to your listening position. Notes: • The “Center” distance cannot be set if the “Center” is set to “None” (page 104). • The “SurrRight” and “SurrLeft” distances cannot be set if the “Surround” is set to “None” (page 104).
Advanced Setup—Continued 2 Enter Enter Use the Up and Down [ ]/[ ] buttons to select “2. Speaker Setup”, and then press [Enter]. The “Speaker Setup” menu appears. 1. 2. 3. 4. 5. 6. 2. Speaker Setup Speaker Settings Speaker Config Speaker Distance Level Calibration Equalizer Settings THX Audio Setup MOVE 3 Enter Enter ENTER ENTER RETURN RETURN SETUP EXIT Use the Up and Down [ ]/[ ] buttons to select “4. Level Calibration”, and then press [Enter].
Advanced Setup—Continued Equalizer Settings 2–5. Equalizer Settings 630Hz 1000Hz 1600Hz 2500Hz 4000Hz 6300Hz 10000Hz 16000Hz These settings are set automatically by the Automatic Speaker Setup function (see page 58). With the Equalizer settings, you can adjust the tone of speakers individually with a 7-band equalizer. The volume of each speaker can be set on page 108.
Advanced Setup—Continued ■ MultEQ XT Audyssey MultEQ XT correction is active (see page 58). 6 ■ Dynamic EQ “Audyssey MultEQ XT” and “Dynamic EQ” becomes active (see page 58). Enter ■ Dynamic Vol(Light) “Audyssey MultEQ XT”, “Dynamic EQ”, and “Dynamic Volume (Light Compression Mode)” becomes active (see page 58). Enter This setting prevents loud and soft sounds from being much louder and softer respectively than average sounds.
Advanced Setup—Continued THX Audio Setup 4 These settings are not set automatically by the Automatic Speaker Setup function (see page 58). Enter With the “SurrBack Sp Spacing” setting, you can specify the distance between your surround back speakers. If you’re using a THX-certified subwoofer, set the “THX Subwoofer” setting to “Yes”.
Advanced Setup—Continued 7 Enter Enter 8 Enter Enter 9 Se tu p Use the Up and Down [ ]/[ ] buttons to select “Loudness Plus”, and use the Left and Right [ ]/[ ] buttons to select: Off: Select this to turn off Loudness Plus. On: Select this to turn on Loudness Plus (default). When “Loudness Plus” is set to “Off”, the “Preserve THX settings” selection will appear under “Loudness Plus” (Step 8).
Advanced Setup—Continued 5 Se tu p When you’ve finished, press the [Setup] button. The setup menu closes. Note: This procedure can also be performed on the AV controller by using its [Setup] button, arrow buttons, and [Enter] button. Multiplex/Mono Settings Multiplex ■ Input Ch(Mux) This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.
Advanced Setup—Continued ■ Dimension With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. It can be adjusted from –3 to +3. The default value is 0. Lower settings move the sound field forward. Higher settings move it backward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance.
Advanced Setup—Continued On Standby DVD VCR/DVR Optimizer The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3. TV Input CBL/SAT 1 2 3 + Game/TV AUX 1 AUX 2 TV CH 4 5 6 - Tape Tuner 7 8 CD 9 D.TUN Phono +10 Off: Music Optimizer off (default). On: Music Optimizer on.
Advanced Setup—Continued Using the Late Night Function With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone. Source Setup This section explains items on the “Source Setup” menu. Items can be set individually for each input selector.
Advanced Setup—Continued 5 Enter Use the Up and Down [ ]/[ ] buttons to select an option, and use the Left and Right [ ]/[ ] buttons to change it. The “Source Setup” menu items are explained below. Enter 6 Se tu p When you’ve finished, press the [Setup] button. Setup closes. Name Edit You can enter a custom name for each individual input selector and radio preset for easy identification. When entered, the custom name will appear on the display.
Advanced Setup—Continued Picture Adjust Zoom: The new “4-4. Picture Adjust” item has been added to the “1. Input/Output Assign” menu. This menu and its settings can be accessed just like the other menus. The settings are explained below. ■ Game Mode If video signal delay occurs during play on a video component, such as a Game console, connected to the AV controller, select “Game Mode” on the input selector connected to the component and set it to “On”.
Advanced Setup—Continued Resolution You can specify the output resolution for the HDMI outputs and have the AV controller upconvert the picture resolution as necessary to match the resolution supported by your TV. Available only when Source has been selected under the “1-1. Monitor Out” setting. Through: Select this to pass video through the AV controller at the same resolution and with no conversion (default).
Advanced Setup—Continued R Brightness: With this setting you can adjust the picture red brightness. Can be adjusted from –50 to +50 in steps of 1 (default is 0). “–50” is the darkest. “+50” is the brightest. R Contrast: With this setting you can adjust red Contrast. Can be adjusted from –50 to +50 in steps of 1 (default is 0). “–50” is the least. “+50” is the greatest. G Brightness: With this setting you can adjust the picture green brightness. Can be adjusted from –50 to +50 in steps of 1 (default is 0).
Advanced Setup—Continued Listening Mode Presets 4 On the “Listening Mode Preset” menu, you can specify a default listening mode for each of the audio formats supported by each input selector. The AV controller will then select the listening mode automatically depending on the format of the input signal. You can still select the other listening modes, although the default listening mode will be used the next time you turn on the AV controller. 1 Receiver Se tu p 2 Enter Enter Enter Enter 1. 2. 3.
Advanced Setup—Continued Miscellaneous Setup 4 This section explains items on the “Miscellaneous” menu. Enter +10 0 Clear 11 --/--- 10 Input Selector 12 Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it. The items are explained below.
Advanced Setup—Continued ■ Power On Volume This setting determines what the volume will be each time the AV controller is turned on. When the “Volume Display” preference is set to “Absolute”, the range is “Last”, “Min”, 1 to “Max”. When it’s set to “Relative”, the range is “Last”, –∞ dB, –81 dB to +18 dB. To use the same volume level as when the AV controller was last turned off, select “Last”. Note: The “Power On Volume” setting cannot be set higher than the “Maximum Volume” setting.
Advanced Setup—Continued Hardware Setup 4 Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it. The items are explained below. This section explains items on the Hardware menu. Enter Remote indicator On Standby DVD VCR/DVR CBL/SAT 1 2 3 + Game/TV AUX 1 TV Input Number buttons AUX 2 TV CH 4 5 6 - Tape Tuner CD 7 8 5 When you’ve finished, press the [Setup] button. Setup closes. 9 D.
Advanced Setup—Continued Tuner ■ AM Freq Step (on some models) See “AM Frequency Step Setup (on some models)” on page 57. ■ Satellite Radio (on North American model) If you connect an XM Satellite Radio antenna or SIRIUS Satellite Radio antenna to the AV controller (both sold separately), set this setting to XM or SIRIUS respectively. If you connect both types of antenna, select XM/SIRIUS. Otherwise, select None (see pages 74–88).
Advanced Setup—Continued Power Control To link the power functions of -compatible components connected via HDMI, select “Enable”. Disable: Power Control disabled. Enable: Power Control enabled. Notes: • The “Power Control” setting can be set only when the above “Control” setting is set to “Enable”. • HDMI power control only works with -compatible components that support it and may not work properly with some components due to their settings or compatibility.
Advanced Setup—Continued 3 Enter Use the Up and Down [ ]/[ ] buttons to select “6. Network”, and then press [Enter]. The “Network” screen appears. 7-6. Network MAC Address xx : xx : xx : xx : xx : xx Enable Control xxxxx Port Enter DHCP This setting determines whether or not the AV controller uses DHCP to automatically configure its IP Address, Subnet Mask, and Gateway settings. Enable: DHCP enabled. Disable: DHCP disabled.
Advanced Setup—Continued Selecting Audio Inputs Specifying the Digital Signal Format p y g 1 2 Rec Playlist Random Listening Mode Audio Sel Stereo Surround Repeat Audio Subtitle Direct THX All ST Test Tone CH Sel Level- Level+ Open/Close Video Off Audio Sel L Night Re-EQ VCR DVD HDD Play Mode RC-691M If you connect a component to more than one audio input, such as a DVD player connected to analog, digital, multichannel, and HDMI inputs, you can use the [Audio Sel] button to sel
Zone 2 and Zone 3 In addition to your main listening room, you can also enjoy playback in two other rooms, or as we call them, Zone 2 and Zone 3. And, you can select a different source for each room. Connecting Zone 2 Zone 2 speakers must be connected to an amp in Zone 2. Connecting Your Zone 2 Speakers You can enjoy 2-channel stereo playback in Zone 2 and a different source to those selected for your main room and Zone 3.
Zone 2 and Zone 3—Continued Connecting Zone 3 Zone 3 speakers must be connected to an amp in Zone 3. Connecting Your Zone 3 Speakers You can enjoy 2-channel stereo playback in Zone 3 and a different source to those selected for your main room and Zone 2. Hookup • Use an RCA audio cable to connect the AV controller’s ZONE 3 PRE OUT L/R jacks to an analog audio input on your Zone 3 amp.
Zone 2 and Zone 3—Continued Zone 2/Zone 3 Out Settings 5 If you’ve connected your Zone 2 or Zone 3 speakers to an amp with no volume control, set the “Zone2 Out” or “Zone3 Out” setting, respectively, to “Variable” so that you can set the zone’s volume, balance, and tone on the AV controller. 1 Receiver Se tu p 2 Enter Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen.
Zone 2 and Zone 3—Continued Selecting an Input Source for Zones 1 Remote controller On the remote controller, press the [Zone2] or [Zone 3] Remote Mode button. Turning Off Zones 1 Remote controller On the AV controller, press the [Zone 2] or [Zone 3] button. AV controller On the AV controller, press the [Zone 2] or [Zone 3] button. AV controller The Zone 2 or Zone 3 indicator flashes, and the input selector currently selected for the zone appears on the display.
Zone 2 and Zone 3—Continued Adjusting the Volume of Zones 1 Remote controller On the remote controller, press the [Zone2] or [Zone 3] Remote Mode button. Adjusting the Tone and Balance of Zones 1 AV controller On the AV controller, press the [Zone 2] or [Zone 3] button. On the AV controller, press the [Zone 2] or [Zone 3] button. AV controller The Zone 2 or Zone 3 indicator flashes. 2 Remote controller On the remote controller, press the [Level–] and [Level+] button.
Zone 2 and Zone 3—Continued Using the 12V Triggers 3 The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for the main room, Zone 2, Zone 3, or any combination of rooms. When triggered, the output from a 12V TRIGGER OUT goes high (+12 volts, 100 milliamperes max).
Zone 2 and Zone 3—Continued Using the Remote Controller in Zone 2/3 and Multiroom Control Kits To control the AV controller with the remote controller while you’re in Zone 2 or Zone 3, you’ll need a commercially available multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV controller’s remote sensor, such as when it’s installed inside a cabinet.
Controlling Other Components You can control your other components, including those made by other manufacturers, with the remote controller. This section explains how to: • Enter the remote control code for a component that you want to control: DVD, TV, VCR, etc. • Learn commands directly from another component’s remote controller (see page 140). • Program the Macro buttons to perform a sequence of up to eight remote control actions (see page 141).
Controlling Other Components—Continued Remote Control Codes for Integra/Onkyo Components Connected via Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the AV controller, not the component. This allows you to control components that are out of view, in a rack, for example.
Controlling Other Components—Continued To control another component, point the remote controller at it and use the buttons explained below. (You must select the appropriate remote controller mode with the Remote Mode buttons first.) With some components, certain buttons may not work as expected, and some may not work at all.
Controlling Other Components—Continued Learning Commands If the command is learned successfully, the Remote indicator flashes twice. ST E TEON T L SE H C PE TA D C O C IS D C W PO ER D VD VID -1 EO D P EE SL D N R O TO PH by I T V T 3 t Inpu + T V C H - T V VO L 140 tu p SA Display Gu id Se L/ Prev CH CB u Men u Enter - UN D.
Controlling Other Components—Continued Using Macros You can program the remote controller’s Macro buttons to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the following actions: 1. Press the [Receiver] Remote Mode button to select the Receiver remote controller mode. 2. Press the [On] button to turn on the AV controller. 3. Press the [CD] Input Selector button to select the CD input source. 4.
Troubleshooting If you have any trouble using the AV controller, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. If you can’t resolve the issue yourself, try resetting the AV controller before contacting the dealer from whom you purchased this unit. To reset the AV controller to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [On/Standby] button.
Troubleshooting—Continued There’s no sound with a certain signal format • Check the digital audio output setting on the source component. On some game consoles, such as those that can play DVDs, the default setting is off. • With some DVD-Video discs, you need to select an audio format from a menu or with the [Audio] button on your DVD player’s remote controller. • Depending on the input signal, some listening modes cannot be selected (pages 91-96).
Troubleshooting—Continued The immediate display does not appear • The immediate display will not appear when the input signal from the COMPONENT VIDEO IN is output to a device connected to the COMPONENT VIDEO MONITOR OUT. • Depending on the input signal, the immediate display may not appear when the input signal from the HDMI IN is output to a device connected to the HDMI OUT. Tuner Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t appear • Relocate your antenna.
Troubleshooting—Continued Others The sound changes when I connect my headphones • When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct. The speaker volume cannot be set as required • When the Automatic Speaker Setup function is used, or the volume is adjusted on the onscreen setup menus, the maximum possible volume setting may change.
Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV controller.
Specifications Amplifier Section General THD (Total Harmonic Distortion) Input Sensitivity and Impedance Power Supply North American: Australian: Power Consumption North American: Australian: Dimensions (W × H × D) Output Level and Impedance Phono Overload Frequency Response Tone Control Signal to Noise Ratio 0.05% (Power Rated) 200 mV/ 47 kΩ (LINE) 2.5 mV/47 kΩ (PHONO MM) 200 mV/ 470 Ω (REC OUT) 70 mV (MM 1 kHz, 0.
Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 En Y0810-2 SN 29344765A (C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.