Table of contents ≫ Connections ≫ - Connecting Speakers ≫ Playback ≫ Setup ≫ Troubleshooting ≫ Instruction Manual Appendix ≫ En Supplementary Information ≫ DRX-7.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ What’s in the box Additional Function (Firmware Update) Update Information of the firmware Operation of added new functions Firmware Update Procedure Part Names Front Panel Display Rear Panel Remote Controller 5 6 6 6 7 10 10 12 13 15 Connecting speakers Speaker Installation Speaker Connections and "Speaker Setup" Settings Connecting a Power Amplifier Speaker combinations Connecting the TV To ARC/eARC TV To Non-ARC TV Connecting Playback Devices Connecting an
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Internet Radio Playing Back Spotify AirPlay® Playing Back on This Unit Playing Back on multiple devices (AirPlay2) DTS Play-Fi® Playing Back FlareConnectTM Playing Back USB Storage Device Basic Operations Device and Supported Format Playing back files on a PC and NAS (Music Server) Windows Media® Player settings Playing Back Supported Audio Formats Play Queue Initial Setup Adding Play Queue Information Sort and Delete Playing Back Amazon Music 89 89 91 92 92 9
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening Mode Selecting a Listening mode Speaker Layouts and Selectable Listening Modes Listening Mode Effects Input Formats and Selectable Listening Modes Inputting Characters 126 126 128 131 137 148 Setup Menu Menu list Menu operations 1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Listening Mode Preset 6. Hardware 7. Multi Zone 8.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ What’s in the box 1. Main unit (1) 2. Remote controller (RC-978R) (1), Batteries (AAA/R03) (2) 3. Speaker setup microphone (1) • Used during Initial Setup. 4. Indoor FM antenna (1) 5. AM loop antenna (1) 6. Power cord (1) • Initial Setup Guide (1) * This is an online user manual. This is not supplied with the product. • Connect speakers with an impedance of 4 Ω to 16 Ω.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Additional Function (Firmware Update) This unit is equipped with a function to update the firmware via network or USB port when the firmware update is announced after purchase. This enables various functions to be added and operations to be improved. Depending on the manufacturing timing of the product, the firmware may be switched to the updated one. In such a case, new functions may be added from the start.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Firmware Update Procedure Update 1. Press . The Setup menu is displayed on the TV screen. The update may take approx. 30 minutes to complete via network or via USB port. Existing settings are guaranteed in either updating method. When this unit is connected to the network, notifications of firmware updates may be displayed. To update the firmware, select "Update Now" with the cursor buttons of the remote controller and press Enter.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ • • • • 4. Press On/Standby on the main unit to turn the unit into standby mode. The process is completed, and your firmware is updated to the latest version. • Do not use on the remote controller. If an Error Message is Displayed If an error occurs, "- Error!" is displayed on the display of the unit. ("" represents an alphanumeric character.) Refer to the following descriptions and check. Turn off control devices (PC etc.) connected to the network.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ If an Error Message is Displayed If an error occurs, "- Error!" is displayed on the display of the unit. ("" represents an alphanumeric character.) Refer to the following descriptions and check. Setup 1. Input/Output Assign 1. TV Out / OSD 2. Speaker 2. HDMI Input 3. Audio Adjust 3. Video Input 4. Source 4. Digital Audio Input 5. Listening Mode Preset 5. Analog Audio Input Error Code • -01, -10: The USB storage device cannot be recognized.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Part Names Front Panel For details, see ( 10 p11) Front Panel≫ Rear Panel≫ Remote≫
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Off button: Switches the multi-zone function off. 18. Whole House Mode button: Enables the WHOLE HOUSE MODE function to play the same source in all the multi-zone connected rooms. ( p117, 119) Off button: Switches the WHOLE HOUSE MODE function off. 19. Phones jack: Connect headphones with a standard plug (ø1/4″/6.3 mm). 20. Setup Mic jack: Connect the supplied speaker setup microphone. ( p191) 21. Input selector buttons: Switches the input to be played. 22.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Display 1. Speaker/Channel display: Displays the output channel that corresponds to the selected listening mode. 2. Lights in the following conditions. : Headphones are connected. Z2/Z3: ZONE 2/ZONE 3 is on. : Connected by BLUETOOTH. : Connected by Wi-Fi. NET: Lights when connected to the network with the "NET" input selector. It will blink if incorrectly connected to the network.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Rear Panel ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 VIDEO IN 1 1 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 5 V / 1A eARC ARC AC INLET USB 4K HDR 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME) 2 ( TV ) OPTICAL COAXIAL ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) (LINE OUT ) ( GAME ) Y PB PR COMPONENT RS232 4 5 ( GAME ) (CD) 6 FRONT CENTER SURROUND BACK 1 HEIGHT 2 1 L TUNER SUBWOOFE
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 1. COMPONENT VIDEO IN jacks: Input AV component video signals with a component video cable. (Compatible only with 480i or 576i resolution.) 2. Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTHenabled device. Adjust the angles according to the connection status. 3. VIDEO IN jacks: Input AV component video signals with an analog video cable. 4. AUDIO IN jacks: Input AV component audio signal with an analog audio cable. 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Remote Controller 1. On/Standby button 2. Input selector buttons: Switches the input to be played. 3. Dimmer button: You can switch the display off or adjust the brightness of the display in three steps. 4. Q (Quick Menu) button: Pressing this button during playback can make settings such as "HDMI" and "Audio" quickly on the TV screen. ( p186) 5. Cursor buttons and Enter button: Select an item with the cursors, and press Enter to confirm your selection.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 18. CH SEL button: You can check the volume level settings ( p161) for each of the speakers. You can also change the settings with the number 5 cursor buttons / . 19. M.OPT button: Turns on/off the Music Optimizer ( p187) function that improves the quality of the compressed audio. 20. button: Temporarily mutes audio. Press the button again to cancel muting. 21. VOLUME buttons 22. button: You can start repeat or random play of the Music Server or USB.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connections Connecting speakers Connecting the TV Connecting Playback Devices Connecting an AV Component in a Separate Room (Multi-zone Connection) Connecting ZONE B Connecting Antennas Network Connection Connecting External Control Devices Connecting the Power Cord 18 70 73 77 80 81 82 83 85 17 Front Panel≫ Rear Panel≫ Remote≫
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting speakers You can select the layout of speakers to be installed from various patterns when using this unit. Use the following flow chart to select the speaker layout that suits your speakers and usage environment. You can check the connection method and default settings. Use height speakers? Yes No When using 1 set of Height Speakers • 5.1.2 Channel System ( p57) • 5.1.2 Channel System + ZONE SPEAKER ( p58) • 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Speaker Installation 5.1 Channel System This is a basic 5.1 Channel System. Front speakers output the front stereo sound, and a center speaker outputs the sound of the center of the screen, such as dialogs and vocals. Surround speakers create the back sound field. Powered subwoofer reproduces the bass sound, and creates the rich sound field.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1 Channel System This is a 7.1 Channel System that consists of the basic 5.1 Channel System ( p19) and added surround back speakers. Front speakers output the front stereo sound, and a center speaker outputs the sound of the center of the screen, such as dialogs and vocals. Surround speakers create the back sound field. Powered subwoofer reproduces the bass sound, and creates the rich sound field.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.2 Channel System A 5.1.2 Channel System is a speaker layout consisting of the basic 5.1 Channel System ( your speakers and usage environment from the following three types. p19) and added height speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Front High Speakers/Rear High Speakers Installation Example This is a system with the basic 5.1 channel system ( p19) consisting of front speakers, a center speaker, surround speakers and a powered subwoofer, and added front high speakers or rear high speakers combined. Installing the height speakers will enrich the sound field feeling in the upper space. Front high speakers or rear high speakers should be installed at least 3'/0.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Ceiling Speakers Installation Example This is a system with the basic 5.1 channel system ( p19) consisting of front speakers, a center speaker, surround speakers and a powered subwoofer, and added top front speakers or top middle speakers or top rear speakers combined. Installing the height speakers will enrich the sound field feeling in the upper space.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Dolby Enabled Speakers (Dolby Speakers) Installation Example This is a system with the basic 5.1 channel system ( p19) consisting of front speakers, a center speaker, surround speakers and a powered subwoofer, and added Dolby enabled speakers (front) or Dolby enabled speakers (surround) combined. Dolby enabled speakers are special speakers designed to face the ceiling, so that the sound is heard from overhead by bouncing the sound off the ceiling.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1.2 Channel System A 7.1.2 Channel System is a speaker layout consisting of the 7.1 Channel System ( speakers and usage environment from the following three types. p20) and added height speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Front High Speakers/Rear High Speakers Installation Example This is a system with the 7.1 channel system ( p20) consisting of front speakers, a center speaker, surround speakers, surround back speakers and a powered subwoofer, and added front high speakers or rear high speakers combined. Installing the height speakers will enrich the sound field feeling in the upper space. Front high speakers or rear high speakers should be installed at least 3'/0.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Ceiling Speakers Installation Example This is a system with the 7.1 channel system ( p20) consisting of front speakers, a center speaker, surround speakers, surround back speakers and a powered subwoofer, and added top front speakers or top middle speakers or top rear speakers combined. Installing the height speakers will enrich the sound field feeling in the upper space.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Dolby Enabled Speakers (Dolby Speakers) Installation Example This is a system with the 7.1 channel system ( p20) consisting of front speakers, a center speaker, surround speakers, surround back speakers and a powered subwoofer, and added Dolby enabled speakers (front), Dolby enabled speakers (surround) or Dolby enabled speakers (surround back) combined.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.4 Channel System A 5.1.4 Channel System is a speaker layout combining 2 sets of the height speakers, 1 set of left and right at the front and 1 set of left and right at the rear, to the basic 5.1 Channel System ( p19). Installing the height speakers will enrich the sound field feeling in the upper space. Combination of 2 height speakers can be selected from following.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Top Front Speakers are used at the front (Example 1) Use top rear speakers at the rear About the top front speakers b b: 125° to 150° The top rear speakers are installed on the ceiling at rear of the listening position, and the width between the left and right speakers is optimal to match the one for the front speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 2) Use rear high speakers at the rear 3´ (0.9 m) or more The width between the rear high speakers should match the one for the front speakers, and they should be installed minimum of 3'/0.9 m higher than the front speakers, and tilted so they will point toward the listener.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Top Middle Speakers are used at the front Use rear high speakers at the rear About the top middle speakers 3´ (0.9 m) or more The width between the rear high speakers should match the one for the front speakers, and they should be installed minimum of 3'/0.9 m higher than the front speakers, and tilted so they will point toward the listener.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Front High Speakers are used at the front (Example 1) Use rear high speakers at the rear About the front high speakers 3´ (0.9 m) or more The width between the rear high speakers should match the one for the front speakers, and they should be installed minimum of 3'/0.9 m higher than the front speakers, and tilted so they will point toward the listener. 3´ (0.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 2) Use top middle speakers at the rear (Example 4) Use Dolby Enabled Speakers (Surround) at the rear c The top middle speakers are installed on the ceiling immediately above the listening position, and the width between the left and right speakers is optimal to match the one for the front speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Dolby Enabled Speakers (Front) are used at the front (Example 1) Use top rear speakers at the rear About the Dolby enabled speakers (front) c c: 125° to 150° The top rear speakers are installed on the ceiling at rear of the listening position, and the width between the left and right speakers is optimal to match the one for the front speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 2) Use rear high speakers at the rear 3´ (0.9 m) or more The width between the rear high speakers should match the one for the front speakers, and they should be installed minimum of 3'/0.9 m higher than the front speakers, and tilted so they will point toward the listener.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1.4 Channel System A 7.1.4 Channel System is a speaker layout combining 2 sets of the height speakers, 1 set of left and right at the front and 1 set of left and right at the rear, to the basic 7.1 Channel System ( p20). Installing the height speakers will enrich the sound field feeling in the upper space. Combination of 2 height speakers can be selected from following.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Top Front Speakers are used at the front (Example 1) Use top rear speakers at the rear About the top front speakers b b: 125° to 150° The top rear speakers are installed on the ceiling at rear of the listening position, and the width between the left and right speakers is optimal to match the one for the front speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 2) Use rear high speakers at the rear (Example 4) Use Dolby Enabled Speakers (Surround Back) at the rear 3´ (0.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Top Middle Speakers are used at the front Use rear high speakers at the rear About the top middle speakers 3´ (0.9 m) or more The width between the rear high speakers should match the one for the front speakers, and they should be installed minimum of 3'/0.9 m higher than the front speakers, and tilted so they will point toward the listener.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Front High Speakers are used at the front (Example 1) Use rear high speakers at the rear About the front high speakers 3´ (0.9 m) or more 3´ (0.9 m) or more The width between the rear high speakers should match the one for the front speakers, and they should be installed minimum of 3'/0.9 m higher than the front speakers, and tilted so they will point toward the listener.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 2) Use top middle speakers at the rear (Example 4) Use Dolby Enabled Speakers (Surround) at the rear d d: 65° to 100° The Dolby enabled speakers are the special speaker that the sound is emitted toward the ceiling, and have the effect the sound to come from above by reflecting the sound on the ceiling. The Dolby enabled speakers (surround) are installed on top of the surround speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 5) Use Dolby Enabled Speakers (Surround Back) at the rear The Dolby enabled speakers are the special speaker that the sound is emitted toward the ceiling, and have the effect the sound to come from above by reflecting the sound on the ceiling. The Dolby enabled speakers (surround back) are installed on top of the surround back speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Combination example when Dolby Enabled Speakers (Front) are used at the front (Example 1) Use top rear speakers at the rear About the Dolby enabled speakers (front) d d: 125° to 150° The top rear speakers are installed on the ceiling at rear of the listening position, and the width between the left and right speakers is optimal to match the one for the front speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (Example 2) Use rear high speakers at the rear (Example 4) Use Dolby Enabled Speakers (Surround Back) at the rear 3´ (0.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Speaker Connections and "Speaker Setup" Settings Connections (Note) Speaker Impedance Connect speakers with an impedance of 4 Ω to 16 Ω. Connect the Speaker Cables 3/8˝ (10 mm) Make correct connection between the unit's jacks and speaker's jacks (+ side to + side, and - side to - side) for each channel. If the connection is wrong, a bass sound will not be reproduced properly due to reverse phase.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connect the Subwoofer SUB MAIN HDMI OUT DIGITAL IN eARC ARC 5 V / 1A AC INLET USB 4K HDR ETHERNET ( ASSIGNABLE ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME ) 2 (CD) HDBaseT TM 3 ( TV ) OPTICAL COAXIAL SUBWOOFER PHONO FRONT IN OUT GND CENTER SURROUND BACK 1 HEIGHT 2 1 RS 232 L ON OFF 12V 1A INPUT 2 ASSIGNABLE ) R IR PRE OUT IN OUT a a Subwoofer cable Connect a powered subwoofer with a subwoofer cable.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting a Power Amplifier Power amplifier You can connect a power amplifier to the unit and use the unit as a pre-amplifier in order to produce a large volume that cannot be output with the unit only. Connect the speakers to the power amplifier. For details, refer to the power amplifier's instruction manual. • Use the PRE OUT jacks for connection as show on the left. a Setup • Set "2.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Speaker combinations • Up to two powered subwoofers can be connected in either combination. Speaker Channels 2.1 ch 3.1 ch 4.1 ch 5.1 ch 6.1 ch 7.1 ch 2.1.2 ch 3.1.2 ch 4.1.2 ch 5.1.2 ch 6.1.2 ch 7.1.2 ch 4.1.4 ch 5.1.4 ch 6.1.4 ch 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ –– Height 1 Speaker: Front High; Height 2 Speaker: One of Rear High/Top Middle/Top Rear/Dolby Enabled Speaker (Surround)/Dolby Enabled Speaker (Surround Back) –– Height 1 Speaker: Top Front or Dolby Enabled Speaker (Front), Height 2 Speaker: One of Rear High/Top Rear/Dolby Enabled Speaker (Surround)/Dolby Enabled Speaker (Surround Back) When only 1 set of the height speakers is connected, 1 from the height speakers types can be selected.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting the TV Connect this unit between a TV and AV component. Connecting this unit with the TV can output the video and audio signals of the AV component to the TV, or play the audio of the TV on this unit. Connection with the TV differs depending on whether the TV supports the ARC (Audio Return Channel) function or eARC (Enhanced Audio Return Channel) function.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ To ARC/eARC TV ZONE 2 SUB MAIN HDMI OUT DIGITAL IN eARC ARC 5 V / 1A AC INLET USB 4K HDR ETHERNET ( ASSIGNABLE ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME ) 2 HDBaseT TM 3 (CD) ( TV ) OPTICAL COAXIAL 6 ( T V) SUBWOOFER PHONO FRONT IN OUT GND CENTER SURROUND BACK 1 HEIGHT 2 1 RS 232 L ON OFF 12V 1A INPUT 2 R IR PRE OUT ( 1 ~6 ASSIGNABLE ) IN CENTER HEIGHT 2 R ( ZONE 2 ) L SURROUND BACK R L OUT SURROUND R L R HEIGHT
Contents ≫ Connections ≫ Playback ≫ Setup ≫ To Non-ARC TV SUB MAIN HDMI OUT DIGITAL IN 5 V / 1A eARC ARC AC INLET USB 4K HDR ETHERNET ( ASSIGNABLE ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME ) 2 HDBaseT TM 3 (CD) ( TV ) OPTICAL COAXIAL SUBWOOFER FRONT IN OUT GND PHONO If the TV does not support the ARC (Audio Return Channel) function (*), connect an HDMI cable and digital optical cable.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting Playback Devices Connecting an AV Component with HDMI Jack Mounted ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 HDMI IN ( ASSIGNABLE ) VIDEO IN ( ASSIGNABLE ) 1 1 ( BD / DVD ) ( GAME ) 2 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 eARC ARC 5 V / 1A USB 4K HDR ( ASSIGNABLE ) ( CBL / SAT ) ( STRM BOX ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME GND ( BD /DVD ) COAXIAL 2 ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting an AV Component without HDMI Jack Mounted ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 HDMI IN ( ASSIGNABLE ) VIDEO IN ( ASSIGNABLE ) 1 1 ( BD / DVD ) ( GAME ) 2 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 eARC ARC 5 V / 1A USB 4K HDR ( ASSIGNABLE ) 1 2 ( BD/ DVD) ( CBL / SAT ) ( CBL / SAT ) ( STRM BOX ) 1 (GAME GND ( BD /DVD ) COAXIAL 2 ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) (LINE OUT )
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting an Audio Component X) ( CBL / SAT ) 3 HDMI IN VIDEO IN 1 2 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 eARC ARC 5 V / 1A USB 4K HDR ETHERNET ( ASSIGNABLE ) ( CBL / SAT ) ( STRM BOX ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME ) 2 HDBaseT TM 3 (CD) ( TV ) OPTICAL COAXIAL 2 3 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) 4 5 ( GAME ) (CD) 6 ( T V) SUBWOOFER PHONO FRONT IN OUT GND 1 This is a connection example of
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting a Video Camera, etc. Connect a video camera, etc. to the AUX Input HDMI jack on the front panel using an HDMI cable.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting an AV Component in a Separate Room (Multi-zone Connection) Connecting a TV (ZONE 2) ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 2 HDMI IN ( ASSIGNABLE ) VIDEO IN ( ASSIGNABLE ) 1 1 ( BD / DVD ) ( GAME ) 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 eARC ARC 5 V / 1A USB 4K HDR ( ASSIGNABLE ) ( CBL / SAT ) ( STRM BOX ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME GND ( BD /DVD ) COAXIAL 2 ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL /
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting a Pre-main Amplifier (ZONE 2) ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 HDMI IN ( ASSIGNABLE ) VIDEO IN ( ASSIGNABLE ) 1 1 ( BD / DVD ) ( GAME ) 2 1 You can enjoy 2-ch audio in the separate room (ZONE 2) while performing playback in the main room (where this unit is located).
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting a Pre-main Amplifier (ZONE 3) ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 HDMI IN ( ASSIGNABLE ) VIDEO IN ( ASSIGNABLE ) 1 1 ( BD / DVD ) ( GAME ) 2 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 eARC ARC 5 V / 1A USB 4K HDR ( ASSIGNABLE ) ( CBL / SAT ) ( STRM BOX ) 1 2 ( BD/ DVD) ( CBL / SAT ) 1 (GAME GND ( BD /DVD ) COAXIAL 2 ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) (LINE OUT ) ( GAME ) Y
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting ZONE B Connecting a Pre-main Amplifier, etc.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting Antennas ( PC) 6 5 ( STRM BOX ) ( CBL / SAT ) 4 3 HDMI IN ( ASSIGNABLE ) VIDEO IN ( ASSIGNABLE ) 1 1 ( BD / DVD ) ( GAME ) 2 1 ZONE 2 SUB MAIN HDMI OUT 4K HDR DIGITAL IN 2 Y PB ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) (LINE OUT ) PR COMPONENT RS232 TUNER FM 5 V / 1A USB 4K HDR 1 2 ( BD/ DVD) ( CBL / SAT ) GND 2 ARC ( ASSIGNABLE ) ( CBL / SAT ) ( STRM BOX ) ( BD /DVD ) ( GAME ) eARC
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Network Connection SUB MAIN HDMI OUT DIGITAL IN eARC ARC 5 V / 1A AC INLET ETHERNET USB 4K HDR ( ASSIGNABLE ) 1 2 1 ( BD/ DVD) ( CBL / SAT ) (GAME ) 2 HDBaseT TM 3 (CD) ( TV ) OPTICAL COAXIAL SUBWOOFER FRONT IN OUT GND PHONO This unit can be connected to the network using a wired LAN or Wi-Fi (wireless LAN). You can enjoy network functions such as Internet radio by network connection.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting External Control Devices IR IN/OUT port COAXIAL 2 ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) (LINE OUT ) ( GAME ) Y PB PR COMPONENT RS232 TUNER FM 4 5 ( GAME ) (CD) 6 ( T V) SUBWOOFER PHONO L 1 R 2 FRONT CENTER SURROUND 75 AM PRE/LINE OUT AUDIO IN R IR FRONT L PRE OUT ( 1 ~6 ASSIGNABLE ) CENTER HEIGHT 2 R ( ZONE 2 ) L When connecting a remote control receiver unit consisting of an IR Recei
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 12V TRIGGER OUT jack COAXIAL 2 ZONE 2 1 2 3 ZONE B ZONE 3 ( CBL / SAT ) ( STRM BOX ) ( BD / DVD ) (LINE OUT ) ( GAME ) Y PB PR COMPONENT RS232 TUNER FM 4 5 ( GAME ) (CD) 6 ( T V) SUBWOOFER PHONO L 1 R 2 FRONT CENTER SURROUND 75 AM PRE/LINE OUT AUDIO IN R IR FRONT L PRE OUT ( 1 ~6 ASSIGNABLE ) CENTER HEIGHT 2 R ( ZONE 2 ) L When connecting a device equipped with a TRIGGER IN jack such as a BD/DVD player to this unit, the devic
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting the Power Cord Connect the power cord after all the connections are completed. • This model includes a removable power cord. Be sure to connect the power cord to the AC INLET of the unit first, and then connect it to the outlet. Always disconnect the outlet side first when disconnecting the power cord.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playback AV Component Playback BLUETOOTH® Playback Internet Radio Spotify AirPlay® DTS Play-Fi® FlareConnectTM USB Storage Device Playing back files on a PC and NAS (Music Server) Play Queue Amazon Music Connecting the Sonos System for Playback Listening To the AM/FM Radio Multi-zone ZONE B Playback Convenience functions Listening Mode Inputting Characters 87 88 89 91 92 94 95 96 99 104 106 108 110 115 120 121 126 148 86 Front Panel≫ Rear Panel≫ Remote≫
Contents ≫ Connections ≫ Playback ≫ Setup ≫ AV Component Playback You can play the audio from AV components, such as Blu-ray disc players through this unit. • When a TV is connected to the HDMI OUT SUB jack, use the HDMI Main/Sub button or "Quick Menu" ( p186) to switch between MAIN and SUB. Basic Operations Perform the following procedure when this unit is on. 1. Switch the input on the TV to the input connected to the unit. 2.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ BLUETOOTH® Playback You can wirelessly play the audio on a BLUETOOTH-enabled device, such as a smartphone. Basic Operations Perform the following procedure when this unit is on. Pairing 1. When you press the Bluetooth button, "Now Pairing..." appears on the display, and the pairing mode is enabled. 2. Enable (turn on) the BLUETOOTH function of the BLUETOOTH-enabled device, and then select this unit from among the devices displayed.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Internet Radio By connecting this unit to an Internet-connected network, you can enjoy Internet radio services such as TuneIn Radio. • To play Internet radio services, the network needs to be connected to the Internet. • Depending on the Internet radio service, a user registration may be required on your PC beforehand. For details of each service, visit the website of each service. Playing Back Perform the following procedure when this unit is on. 1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Internet Radio Service Menu You can bookmark specific stations, or delete stations that have been bookmarked. The displayed menu varies according to the service being selected. The menu icon is displayed while a station is being played. When only this icon is displayed, pressing Enter will display the menu on the screen. When multiple icons are displayed, select the icon with the cursor, and press Enter.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Spotify Use your phone, tablet or computer as a remote control for Spotify. Go to spotify.com/connect to learn how.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ AirPlay® By connecting this unit to the same network as that of iOS devices such as iPhone®, iPod touch® and iPad®, you can enjoy music files on iOS devices wirelessly. • Update the OS version on your iOS device to the latest version. • Depending on the iOS version, operation screens or operation procedures on the iOS device may be different. For details, refer to the operating instructions for the iOS device. Playing Back on This Unit 1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playing Back on multiple devices (AirPlay2) This unit supports AirPlay2. If the version of the iOS device is iOS11.4 or later, you can play the music of the iOS device on this unit and other devices that support AirPlay2. 1. Connect the iOS device to the access point where this unit is connected via network. 2.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ DTS Play-Fi® 2. Connect the mobile device to the network where this unit is connected. 3. Starting up Integra Music Control App will automatically display compatible devices. 4. Select this device from the compatible devices. Then, a list of applications such as a music streaming distribution service is displayed. Select the content to play, and perform operation according to the on-screen instructions. https://play-fi.com/ • When "6.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ FlareConnectTM When downloading Integra Control Pro (available on iOS or Android™) to mobile devices, such as a smartphone and tablet, you can enjoy the group playback that plays the same music on multiple audio products supporting the FlareConnect function.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ USB Storage Device You can play music files stored on a USB storage device. Basic Operations Perform the following procedure when this unit is on. 1. Switch the input on the TV to the input connected to the unit. 2. Plug your USB storage device containing music files into the USB port of this unit's rear panel. 3. Press NET to display the network service list screen. 4. Select "USB" with the cursors, and then press Enter.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ • To return to the previous screen, press . • To display an album title, artist name and album art of a file in WAV format, make the folder structure and file names as shown below when saving music files. The album art can be displayed by saving a .jpg file to display on the screen in the folder of bottom level. Note that a large volume of .jpg file may take time to be displayed, or may not be displayed.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Device and Supported Format USB Storage Device Requirements WAV (.wav/.WAV): WAV files contain uncompressed PCM digital audio. • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz • Quantization bit: 8 bit, 16 bit, 24 bit • This unit can use USB storage devices that comply with the USB mass storage class standard. • The format of USB storage devices supports FAT16 or FAT32 file system format.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playing back files on a PC and NAS (Music Server) Streaming play of music files stored on PCs or NAS devices connected to the same network as this unit is supported. • The network servers supported by this unit are PCs that incorporate players equipped with the server functions such as Windows Media® Player 11 or 12, or NASes supporting the home network function. When using Windows Media® Player 11 or 12, you need to make the settings beforehand.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playing Back Perform the following procedure when this unit is on. 1. Switch the input on the TV to the input connected to the unit. 2. Start the server (Windows Media® Player 11, Windows Media® Player 12, or NAS device) containing the music files to play. 3. Make sure that the PC or NAS is properly connected to the same network as this unit. 4. Press NET to display the network service list screen.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 6. Select the target server with the cursors, and press Enter to display the items list screen. • This unit cannot access pictures and videos stored on servers. • Depending on the server sharing settings, contents stored on the server may not be displayed. 7. With the cursors, select the music file to play, and then press Enter to start playback. • If "No Item" is displayed on the screen, check whether the network is properly connected.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ –– It is playing a music file on a USB storage device. • Depending on the version of Windows Media® Player, the names of items to select may differ from the above description.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Supported Audio Formats This unit supports the following music file formats. Remote play of FLAC and DSD is not supported. MP3 (.mp3/.MP3): • Supported formats: MPEG-1/MPEG-2 Audio Layer 3 • Supported sampling rates: 44.1 kHz, 48 kHz • Supported bitrates: Between 8 kbps and 320 kbps, and VBR Apple Lossless (.m4a/.mp4/.M4A/.MP4): • Supported sampling rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz • Quantization bit: 16 bit, 24 bit DSD (.dsf/.dff/.DSF/.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Play Queue Adding Play Queue Information 1. Select the "INPUT" input on the application screen, and tap the "USB" icon. Or, select the "NET" input, and tap the "USB" icon or "Music Server" icon. (Depending on the model, the icon names may be different.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ • If there are no tracks on the Play Queue list, only "Play Now displayed. " is Sort and Delete 3. To delete a track, slide the track to the left until the trash icon changes to " ". If the device is on iOS, slide the " " icon to the left. Releasing your finger will delete the track from Play Queue. 1. Select the "NET" input, tap the "Play Queue" icon, and enter the Play Queue service screen.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Amazon Music screen to switch to the network menu. Then tap the "Amazon Music" icon to display the login screen of Amazon Music. (Depending on the model, the icon names may be different.) • If the login screen is not displayed but an update or installation screen is displayed instead, perform the update or installation according to the onscreen instructions.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ playback. Playing Amazon Music using the remote controller 1. 2. 3. 4. Switch the input on the TV to the input connected to the unit. Pressing NET will display the Network Functions list screen on the TV. Select "Amazon Music" with the cursors and press Enter to confirm. Select the content to play from the menu screen of Amazon Music to start playback.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Connecting the Sonos System for Playback Setting Up Connecting this unit and Sonos Connect allows you to send the music or music sources on the Sonos App to this unit. Through Sonos Connect, you can play this unit with the same group of another Sonos device on the network or can play only on this unit. Also, if you start to play music from Sonos App, this unit is automatically turned on and the link function to switch input works. • When "6.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ rooms (ZONE 2 and ZONE 3). Preset Volume: You can set the volume that Sonos Connect will be played at in the main room (where this unit is located) beforehand. Select a value from "Last" (Volume level before entering standby mode), "Min", "0.5" to "99.5" and "Max". Playing Sonos on This Unit 1. Select desired tracks using Sonos App and send the tracks to the room where this unit is located (or to the group).
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening To the AM/FM Radio You can receive AM and FM radio stations on this unit with the built-in tuner. Tuning into a Radio Station Perform the following procedure when this unit is on. Tuning Automatically 1. Press Tuner repeatedly to select either "AM" or "FM". 2. Press Mode repeatedly to display "TunMode: Auto" on the display. 3. When you press the cursors / , automatic tuning starts, and searching stops when a station is found.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ When FM broadcasts reception is poor: Perform the procedure for "Tuning Manually" ( p111). Note that if you tune manually, the reception for FM broadcasts will be monaural rather than stereo, irrespective of the sensitivity of the reception. Tuning Manually Note that if you tune manually, the reception for FM broadcasts will be monaural rather than stereo, irrespective of the sensitivity of the reception. 1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Presetting a Radio Station Registration Procedure You can preset up to 40 of your favorite AM/FM radio stations. After tuning in to the AM/FM radio station you want to register, perform the following procedure. 1. Press Memory so that the preset number on the display blinks. 2. While the preset number is blinking (approx. 8 seconds), repeatedly press the cursors / to select a number between 1 and 40. 3. Press Memory again to register the station.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Selecting a Preset Radio Station 1. Press Tuner. 2. Press the cursors / to select a preset number. Deleting a Preset Radio Station 1. Press Tuner. 2. Press the cursors / to select the preset number to delete. 3. After pressing Memory, press Clear while the preset number is blinking, and delete the preset number. When deleted, the number on the display disappears.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Using RDS (Australian models) RDS stands for Radio Data System, and is a method of transmitting data in FM radio signals. In regions where RDS can be used, when you tune in to a radio station broadcasting program information, the radio station name is displayed on the display. When you press the button on the remote controller in this state, you can use the following functions. the unit starts to search for another station.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Multi-zone You can enjoy 2-ch audio in the separate room (ZONE 2/ZONE 3) while performing playback in the main room (where this unit is located). The same source can be played back in the main room and ZONE 2/ZONE 3 simultaneously. Also, different sources can be played back in both rooms. For the "NET" or "BLUETOOTH" input selector, you can select only the same source for the main room and separate room.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playing Back (ZONE 2) In remote controller operation, while pressing and holding the Zone 2 button, press other buttons for operation. 1. While pressing and holding the Zone 2 button on the remote controller, point the remote controller at this unit and press . • "Z2" on the display of the main unit lights up. 2.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ • The audio from externally connected AV components can be output to ZONE 2 only when the audio is analog or 2ch PCM signal. When the AV component is connected to this unit with an HDMI cable, digital coaxial cable or digital optical cable, change the audio output of the AV component to the PCM output. • When video and audio via HDMI input are output to ZONE 2, set "1. Input/ Output Assign" - "TV Out / OSD" - "Zone 2 HDMI" ( p154) to "Use" on the Setup menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playing Back (ZONE 3) In remote controller operation, while pressing and holding the Zone 3 button, press other buttons for operation. 1. While pressing and holding the Zone 3 button on the remote controller, point the remote controller at this unit and press . • "Z3" on the display of the main unit lights up. 2.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ remote controller, press . WHOLE HOUSE MODE: When the Whole House Mode button of the main unit is pressed during playback in the main room, "Z2" and "Z3" on the display light up at the same time, and the WHOLE HOUSE MODE function is turned on with which the same source is played back at once in all rooms. • Sources that can be played in ZONE 2 can be played in all rooms. • In the following cases, this function cannot be used.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ ZONE B Playback While performing playback through speakers (ZONE A) connected to the unit, you can enjoy the audio of the same source with the pre-main amplifier, etc. (ZONE B) ( p80) connected to the ZONE B LINE OUT jack at the same time. Playing Back 1. Press the Q button on the remote controller and select "Audio" - "Zone B". • In the following cases, "Zone B" cannot be selected. –– When ZONE 2 is On –– When "2.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Convenience functions Displaying Your Favorite Video on TV While Playing Music TV’s REMOTE INPUT Inputs TV HDMI 1 HDMI 2 HDMI 3 While listening to the music from a CD or BLUETOOTH-enabled device, you can display video on TV from an AV component such as a Blu-ray Disc player. • For audio playback, you can select an input selector to which video input is not assigned, such as "CD", "PHONO", "TUNER", "NET" and "BLUETOOTH".
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting the video source to be displayed on TV beforehand: When playing the audio of "TUNER", "NET" and "BLUETOOTH", you can set the input selector to be displayed on TV beforehand using "Video Select" ( p169) on the Setup Menu. If a value other than "Last" is set, step 2 in the operation procedure is not required.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Adjusting the tone Adjusting Treble/Bass You can adjust the sound quality of the speakers. 1. Press Treble or Bass to select the content to adjust. Treble: Enhances or moderates the high-tone range of the speakers. Bass: Enhances or moderates the low-tone range of the speakers. 2. Press +, – or the / cursor buttons to adjust. Adjusting Vocal Emphasizes movie lines and music vocals to listen to them more easily. It is effective to movie lines in particular.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Using the Cinema Dedicated mode Cinema Dedicated can improve sound quality by limiting the activity of digital circuits and thereby suppressing the noise that is generated by them. You can choose from "Cinema Dedicated" which temporarily stops communications such as via the network, Bluetooth, and USB, and "Cinema Dedicated Net Off" which turns off the power for some digital circuits.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Sleep Timer You can allow the unit to enter standby automatically when the specified time has elapsed. Press the Sleep button on the remote controller, and select any of "30 min", "60 min" and "90 min". "Off": The unit does not automatically enter standby mode. You can also set this by pressing the button on the remote controller and selecting "6. Hardware" - "Power Management" - "Sleep Timer" ( p174) on the Setup menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening Mode This unit is equipped with a variety of listening modes, and you can select the optimum listening mode for movies, TV, music, and games by pressing Movie/TV, Music, and Game. Selecting a Listening mode 1. Press one from among Movie/TV, Music, and Game during playback. 2. Press the selected button repeatedly to switch the modes displayed on the display of the main unit.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Checking the input format and listening mode Repeatedly pressing the button on the remote controller switches the display of the main unit in the following order. • The display content for the BLUETOOH input is different. • Not all the information is necessarily displayed. Input source and volume Listening mode Input Format The display is switched in a few seconds.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Speaker Layouts and Selectable Listening Modes See the following table for selectable listening modes for each speaker layout. Listening mode Speaker layout (ch) 2.1 3.1 4.1 5.1 6.1 7.1 2.1.2 3.1.2 4.1.2 5.1.2 6.1.2 7.1.2 4.1.4 5.1.4 6.1.4 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode Speaker layout (ch) 2.1 3.1 4.1 5.1 6.1 7.1 2.1.2 DTS 3.1.2 4.1.2 5.1.2 6.1.2 7.1.2 4.1.4 5.1.4 6.1.4 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode Speaker layout (ch) 2.1 3.1 4.1 5.1 6.1 7.1 2.1.2 3.1.2 4.1.2 5.1.2 6.1.2 7.1.2 4.1.4 5.1.4 6.1.4 7.1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening Mode Effects In alphabetical order surround back speakers are installed Atmos 7.0/7.1/7.2: When front speakers, center speaker, surround speakers and surround back speakers are installed –– Atmos 2.0.2/2.1.2/2.2.2: When front speakers and height speakers are installed –– Atmos 3.0.2/3.1.2/3.2.2: When front speakers, center speaker and height speakers are installed –– Atmos: Selectable in the "4.1.2ch", "5.1.2ch", "6.1.2ch", "7.1.2ch", "4.1.4ch", "5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ channels with additional channels such as the surround back channel. • To enable transfer of this audio format, connect via an HDMI cable and set the audio output on the player to Bitstream output. DSur (Dolby Audio - Surr) This listening mode expands 2ch or 5.1ch input signals to 5.1ch, 7.1ch or 5.1.2ch. This mode expands actual channels to more channels for playback according to the configuration of the connected speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ • To enable transfer of this audio format, connect via a digital cable and set the audio output on the player to Bitstream output. from 2 channels or 5.1 channels to 5.1 channels or 7.1 channels respectively. • This mode cannot be selected when Dolby signal is input. DTS Express DTS:X This mode faithfully reproduces the sound design recorded in the DTS Express audio format. DTS Express is an optional audio format based on 5.1ch for Blu-ray Discs.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Game-Action This mode is suitable for games with a lot of action. Game-Rock This mode is suitable for games with rock content. Game-RPG This mode is suitable for role-playing games. displayed, IMAX Mode is optimized for the playback of 5.1 IMAX Enhanced content. When "IMAX DTS:X" is displayed, IMAX Mode is optimized for the playback of fully immersive IMAX Enhanced content.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Stereo In this mode, sound is output from the right and left front speakers and subwoofer. Studio-Mix This mode is suitable for rock or pop music. This mode creates a lively sound field with a powerful acoustic image as if you are at a club or rock concert. T-D (Theater-Dimensional) In this mode, you can enjoy a virtual playback of multichannel surround sound even with only two or three speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ theater or similar large area. In this mode, THX Loudness Plus is set to the theater level, and Re-EQ, Timbre Matching and Adaptive Decorrelation are all enabled. –– THX Games: Use this mode for high-fidelity spatial reproduction of game sound. THX Loudness Plus is set to a level suited to the audio level of the game, and Timbre Matching is enabled.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Input Formats and Selectable Listening Modes You can select a variety of listening modes according to the audio format of the signal to be input. • List of listening modes selectable with the Movie/TV button ( p138) • List of listening modes selectable with the Music button ( p141) • List of listening modes selectable with the Game button ( p144) • Selectable listening modes when headphones are connected are Mono, Direct, and Stereo only.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Movie/TV button Listening mode Direct Input Format Multich(*2) DSD (*2)(*12) DD+ DTHD DD (Dolby Audio (Dolby Audio Atmos (Dolby Audio - DD+) - TrueHD) (*13) - DD) (*2) (*2)(*3) (*2) DSur (Dolby Audio - Surr) (*13) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ DTHD ATMOS DTS DTS 96/24 DTS Express DTS-HD HR DTS-HD MSTR
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode DTS (*2) Input Format DTS 96/24 (*2) DTS Express (*2) DTS-HD HR (DTSHD High Resolution) (*2) DTS-HD Master (DTS-HD Master Audio) (*2) ES Discrete ES Matrix (DTS-ES (DTS-ES DTS:X Discrete) Matrix) (*5) (*5) DTS Neural:X (*6) IMAX DTS (*7) IMAX DTS:X (*7) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ D
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode Mono Input Format TV Logic (*8) AllCh T-D (TheaterTHX THX Select Stereo / Full Dimensional) Cinema(*11) Cinema (*5) Mono (*9) (*10) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ DTHD ATMOS DTS DTS 96/24 DTS Express DTS-HD HR DTS-HD MSTR DTS-ES Discrete DTS-ES Matrix DTS:X IMAX DTS IMAX DTS:X 140 Front Pa
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Music button Listening mode Input Format Direct Stereo DSD Multich (*2) (*2)(*12) DD+ DTHD DD (Dolby Audio (Dolby Audio Atmos (Dolby Audio - DD+) - TrueHD) (*13) - DD) (*2) (*2)(*3) (*2) DSur (Dolby Audio - Surr) (*13) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ DTHD ATMOS DTS DTS 96/24 DTS Express DTS-HD HR DTS-HD
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode DTS (*2) Input Format DTS 96/24 (*2) DTS Express (*2) DTS-HD HR (DTSHD High Resolution) (*2) DTS-HD Master (DTS-HD Master Audio) (*2) ES Discrete ES Matrix (DTS-ES (DTS-ES DTS:X Discrete) Matrix) (*5) (*5) DTS Neural:X (*6) IMAX DTS (*7) IMAX DTS:X (*7) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ D
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode Orchestra / Input Format AllCh Unplugged / THX Music THX Select Stereo / Full Studio-Mix (*11) Music (*5) Mono (*9) (*8) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ DTHD ATMOS DTS DTS 96/24 DTS Express DTS-HD HR DTS-HD MSTR DTS-ES Discrete DTS-ES Matrix DTS:X IMAX DTS IMAX DTS:X 143 Front Panel≫ Rear Pan
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Game button Listening mode Direct Input Format DSD Multich (*2) (*2) (*12) DD+ DTHD DD (Dolby Audio (Dolby Audio Atmos (Dolby Audio - DD+) - TrueHD) (*13) - DD) (*2) (*2)(*3) (*2) DSur (Dolby Audio - Surr) (*13) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ DTHD ATMOS DTS DTS 96/24 DTS Express DTS-HD HR DTS-HD MSTR DT
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode DTS (*2) Input Format DTS 96/24 (*2) DTS Express (*2) DTS-HD HR (DTSHD High Resolution) (*2) DTS-HD Master (DTS-HD Master Audio) (*2) ES Discrete ES Matrix (DTS-ES (DTS-ES DTS:X Discrete) Matrix) (*5) (*5) DTS Neural:X (*6) IMAX DTS (*7) IMAX DTS:X (*7) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ D
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Listening mode Input Format Game-Action / GameRock /Game-RPG / Game-Sports (*8) AllCh T-D (TheaterStereo / Full Dimensional) (*10) Mono (*9) THX Games THX Select (*11) Games (*5) 2-channel signal input Analog / PCM NET / USB / DSD (*1) DD / DD+ / DTHD DTS / DTS 96/24 / DTS Express / DTS-HD HR / DTS-HD MSTR Multi-channel signal input Multich PCM DSD (*1) DD DD+ DTHD ATMOS DTS DTS 96/24 DTS Express DTS-HD HR DTS-HD MSTR DTS-ES Discrete DTS-ES Matrix DTS:X IM
Contents ≫ Connections ≫ Playback ≫ Setup ≫ (*1) You cannot select any mode other than Stereo, AllCh Stereo and Full Mono if the sampling rate is 5.6/11.2 MHz. (*2) A center speaker or surround speakers need to be installed. (*3) If the input source is Blu-ray Disc and the speaker layout is 5.1 ch or less, DD+ cannot be selected. Instead, the listening mode for DD can be selected. (*4) This can only be selected when no surround back speaker is connected.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Inputting Characters You can input characters or symbols on the keyboard displayed on the TV screen such as when inputting a password for Wi-Fi Setup ( p171) or naming a preset radio station ( p168). 1. Select a character or symbol with the cursors / / / on the remote controller and press the Enter button. 2. When saving characters after input, select "OK" and press the Enter button. , . / ; : • Select "A/a" to switch between upper and lower cases.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setup Menu Menu list You can configure advanced settings to have a more enjoyable experience with this unit. For operation details, refer to "Menu operations" ( 1. Input/Output Assign 2. Speaker 1. TV Out / OSD 2. HDMI Input 3. Video Input Make settings for TV output and On-Screen Displays (OSD) that appear on the TV. Change input assignment between the input selectors and HDMI IN jacks.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 4. Source 1. My Input Volume 2. Name Edit Audio Select Video Select Set a volume value for each input selector. Set an easy name for each input. Select the prioritized input terminal when multiple audio sources are connected to one input selector. When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the input from which video is displayed on the TV. p167 p168 p168 p169 5. Listening Mode Preset 1. BD/DVD 2. GAME 3. CBL/SAT 4. STRM BOX 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 8. Miscellaneous 1. Tuner 2. Remote ID 3. Preamp Mode 4. Firmware Update 5. Initial Setup 6. Lock 7. Factory Reset Change the frequency step for the tuner. Change the remote controller ID. If this unit is connected to a power amplifier, you can reduce the power consumed by turning off the power supplied to the SPEAKERS jacks on this unit. Change the settings for Firmware Update. Make the initial setup from the setup menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Menu operations Use the on-screen displays (OSD) that appear on the TV to make the settings. Press on the remote controller to display the Setup menu. Setup 1. Input/Output Assign 1. TV Out / OSD 2. Speaker 2. HDMI Input 3. Audio Adjust 3. Video Input 4. Source 4. Digital Audio Input 5. Listening Mode Preset 5. Analog Audio Input 6. Hardware 7. Multi Zone 8.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 1. Input/Output Assign 1. TV Out / OSD Setting Item Default Value Setting Details 1080p -> 4K Upscaling Off When a TV supporting 4K is used, video signals input with 1080p can be automatically output with 4K. "Off": When this function is not used "Auto": When this function is used If your TV does not support 4K, set it to "Off".
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details HDMI 4K Signal Fomat Standard When an AV component such as a TV or player that supports HDMI 4K is connected to this unit, you can switch the 4K signal format that is input/ output by this unit. "Standard": When the AV component connected to this unit supports the standard 4K signal format (4K 60p 4:2:0 8bit).
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Mini Player OSD Always On You can display on the TV the images from another input selected last while playing the audio from NET or BLUETOOTH input. After switching the input to NET or BLUETOOTH, play the images and audio.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details TV --- "HDMI 1 (HDCP 2.3)" to "HDMI 6 (HDCP 2.3)": Assign a desired HDMI IN jack to the TV button. If you do not assign a jack, select "---". To select an HDMI IN jack already assigned to another input selector, change its setting to "---" first. PC --- "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the PC button.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details PC --- "COAXIAL 1", "COAXIAL 2", "OPTICAL 1", "OPTICAL 2", "OPTICAL 3": Assign a desired DIGITAL IN jack to the PC button. CD OPTICAL 2 "COAXIAL 1", "COAXIAL 2", "OPTICAL 1", "OPTICAL 2", "OPTICAL 3": Assign a desired DIGITAL IN jack to the CD button. TV OPTICAL 3 "COAXIAL 1", "COAXIAL 2", "OPTICAL 1", "OPTICAL 2", "OPTICAL 3": Assign a desired DIGITAL IN jack to the TV button.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details Height 1 Speaker Top Middle Set the speaker type if height speakers are connected to the HEIGHT 1 terminals. Select "Top Middle", "Top Rear", "Rear High", "Dolby Speaker (Front)", "Dolby Speaker (Surr)", "Dolby Speaker (Back)", "Front High" or "Top Front" according to the type and layout of the connected speakers.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Zone Speaker No Set whether speakers are connected to Zone 2 or Zone 3 speaker terminals. "Zone 2": When speakers are connected to Zone 2 speaker terminals "Zone 2/Zone 3": When connecting speaker to both ZONE 2 speaker terminal and ZONE 3 speaker terminals. • "Zone2/Zone3" cannot be selected when height speakers are being used.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details Height 2 80 Hz (THX) Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band".
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 3. Distance Set the distance from each speaker to the listening position. Setting Item Default Value Setting Details Surround Left 7' 0"/2.10 m Specify the distance between each speaker and the listening position. Setting Item Default Value Setting Details Subwoofer 1 12' 0"/3.60 m Front Left 12' 0"/3.60 m Specify the distance between each speaker and the listening position. Specify the distance between each speaker and the listening position.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details Height 1 Right 0.0 dB Select a value between "-12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. • Depending on the use of the ZONE speakers, it may not be possible to select this setting. Subwoofer 1 0.0 dB Select a value between "-15.0 dB" and "+12.0 dB" (in 0.5 dB increments).
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 5. Dolby Enabled Speaker Change the settings of Dolby Enabled Speakers. Setting Item Default Value Dolby Enabled 6' 0"/1.80 m Speaker to Ceiling AccuReflex Off Setting Item Default Value Setting Details Height 1 0.0 dB After selecting the speaker frequency between "25 Hz" and "16 kHz" with the cursors / , adjust the volume of that frequency between "-6.0 dB" and "+6.0 dB" with / .
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 7. THX Audio Change the THX Audio settings. Setting Item Default Value Setting Details Back Speaker Spacing >4.0 ft/>1.2 m Select the distance between the surround back speakers from "<1.0 ft/<0.3 m", "1.0 - 4.0 ft/0.3 1.2 m", and ">4.0 ft/>1.2 m". • The unit of distance (ft/m) is displayed using the unit selected for the "Distance" setting. • Depending on the use of the ZONE speakers, it may not be possible to select this setting.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 3. Audio Adjust 8. EQ for Standing Wave This controls the affect of the standing waves that occur when sound waves reverberating off obstacles such as walls interfere with the original sound waves. Setting Item Filter 1-3 Default Value 0.0 dB Setting Details 1. After selecting the Filter to adjust from "Filter 1" to "Filter 3" with / , press Enter. 2. Select the frequency with / , then adjust the attenuation with / .
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 2. Dolby Change the setting of when Dolby signals are input. Setting Item Default Value Setting Details Loudness Management On When playing Dolby TrueHD, enable the dialog normalization function which keeps the volume of dialog at a certain level. Note that when this setting is Off, the Late Night function that allows you to enjoy surround at low volumes is fixed to off when playing Dolby Digital Plus/Dolby TrueHD.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 4. Source 4. LFE Level Set the low-frequency effect (LFE) level for Dolby Digital series, DTS series, Multichannel PCM, and DSD signals. Setting Item Default Value Setting Details LFE Level 0 dB Select the low-frequency effect (LFE) level of each signal from "0 dB" to "-∞ dB". If the low-frequency effect sound is too strong, select "-20 dB" or "-∞ dB". • This function is disabled when the IMAX sound mode has been applied. 1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 2. Name Edit Audio Select Set an easy name for each input. The set name appears on the main unit's display. Select the input selector to make the setting. Select the priority for input selection when multiple audio sources are connected to one input selector, for example, connections to both the "BD/DVD" HDMI IN jack and the "BD/DVD" AUDIO IN jack. The setting can be made for each input selector button. Select the input selector to make the setting.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details PCM Fixed Mode Off Select whether to fix input signals to PCM (except multi-channel PCM) when you select "HDMI", "COAXIAL", or "OPTICAL" in the "Audio Select" setting. Set this item to "On" if noise is produced or truncation occurs at the beginning of a track when playing PCM sources. Select "Off" normally. • Each time the "Audio Select" setting is changed, the setting is restored to "Off". 5.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 6. Hardware 1. HDMI Change the settings of the HDMI function. Setting Item Default Value Setting Details HDMI CEC Off Setting this to "On" enables the input selection link and other link functions with HDMI-connected CECcompatible device. "On": When this function is used "Off": When this function is not used When this setting is changed, turn off and then on again the power of all connected devices.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Audio TV Out Off You can enjoy audio through the speakers of the TV while this unit is on. "On": When this function is used "Off": When this function is not used • This setting is fixed to "Auto" if you set "1. Input/ Output Assign" - "TV Out/OSD" - "HDMI Out" or "HDMI" - "HDMI Out" in the "Quick Menu" to "MAIN" or "MAIN+SUB" and set "HDMI CEC" to "On". If you change this setting, set "HDMI CEC" to "Off".
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details Proxy URL - Displays/Sets the proxy server URL. Proxy Port 8080 Displays/Sets the proxy server port number when you input "Proxy URL". AirPlay Device Name Integra DRX-7.3 XXXXXX Friendly Name Integra DRX-7.3 XXXXXX Change the model name of this unit which is displayed on the device connected to the network to an easily recognized name. 1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details You can set a password of up to 31 characters so that only users that have input can use AirPlay®. 1. P ress Enter to display the Edit screen. 2. Select a character or symbol with the cursors, and press Enter. Repeat this operation to input up to 31 characters. "A/a": Switches between upper and lower cases.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details Auto Standby On/Off This setting allows the unit to enter standby mode automatically after 20 minutes of inactivity without any video or audio input. (When "USB Power Out at Standby" or "Network Standby" is enabled, the unit enters the Hybrid Standby mode which minimizes the increase in power consumption.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Network Standby On When this function is set to "On", the network function works even in standby state, and you can turn on the power of the unit via network using an application such as Integra Control Pro that can control this unit.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details GAME Main Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "GAME" is selected as input for main room. "Zone 2": Output when "GAME" is selected as input for ZONE2. "Main/Zone 2": Output when "GAME" is selected as input for main room or ZONE2. "Zone 3": Output when "GAME" is selected as input for ZONE3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details CD Main Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "CD" is selected as input for main room. "Zone 2": Output when "CD" is selected as input for ZONE2. "Main/Zone 2": Output when "CD" is selected as input for main room or ZONE2. "Zone 3": Output when "CD" is selected as input for ZONE3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details NET Main Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "NET" is selected as input for main room. "Zone 2": Output when "NET" is selected as input for ZONE2. "Main/Zone 2": Output when "NET" is selected as input for main room or ZONE2. "Zone 3": Output when "NET" is selected as input for ZONE3. "Main/Zone 3": Output when "NET" is selected as input for main room or ZONE3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details GAME Zone 2 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "GAME" is selected as input for main room. "Zone 2": Output when "GAME" is selected as input for ZONE2. "Main/Zone 2": Output when "GAME" is selected as input for main room or ZONE2. "Zone 3": Output when "GAME" is selected as input for ZONE3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details CD Zone 2 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "CD" is selected as input for main room. "Zone 2": Output when "CD" is selected as input for ZONE2. "Main/Zone 2": Output when "CD" is selected as input for main room or ZONE2. "Zone 3": Output when "CD" is selected as input for ZONE3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details NET Zone 2 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "NET" is selected as input for main room. "Zone 2": Output when "NET" is selected as input for ZONE2. "Main/Zone 2": Output when "NET" is selected as input for main room or ZONE2. "Zone 3": Output when "NET" is selected as input for ZONE3. "Main/Zone 3": Output when "NET" is selected as input for main room or ZONE3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Setting Details Output Zone Main Select the zone where you want to listen to the music. "Main": Outputs audio only to the main room (where this unit is located). "Zone 2": Outputs audio only to the separate room (ZONE 2). "Main/Zone 2": Outputs audio to both the main room and separate room. "Zone 3": Outputs audio only to the separate room (ZONE 3). "Main/Zone 3": Outputs audio to both the main room and separate room (ZONE 3).
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Default Value Maximum Volume Off Power On Volume Last 8. Miscellaneous Setting Details Set the maximum value for Zone 3 to prevent the volume from becoming too loud. Select a value from "Off", and "50" to "99". (When "3. Audio Adjust" - "Volume" - "Volume Display" is set to "Absolute") 1. Tuner Change the frequency step for the tuner. Set the Zone 3 volume level of when the unit is turned on.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 2. Remote ID 3. Preamp Mode Change the remote controller ID. If speakers are connected to the PRE OUT jacks on this unit via a power amplifier, you can reduce the power consumed by this unit by turning off the power supplied to the SPEAKERS terminals you are not using on this unit.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Update via USB Default Value Setting Details - Press Enter to select when updating the firmware via USB. • This setting cannot be selected if a USB storage device is not connected or there is no updatable firmware in the USB storage device. • Wait for a while if "Firmware Update" cannot be selected. It can be selected when the network function is activated. 5. Initial Setup Make the initial setup from the setup menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Quick Menu Menu operations You can quickly adjust the settings you frequently use, such as tone adjustments, etc. You can make the settings on the TV screen during playback. Press Q on the remote controller to display the Quick Menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ –– When the "Adjusting Vocal" ( p123) function is being used –– When "Dialog Control" ( p166) has been set –– When the listening mode is Direct listening to the audio of TV using the speakers of this unit. Select "Off" when the ARC function is not used. Audio Music Optimizer: Improve the quality of the compressed audio. Playback sound of lossy compressed files such as MP3 will be improved. The setting can be set for each input.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ • It cannot be set if the listening mode is Direct. Level Front: Adjust the speaker level of the front speakers while listening to the sound. Center: Adjust the speaker level of the center speaker while listening to the sound. Subwoofer 1/Subwoofer 2: Adjust the speaker level of the subwoofer while listening to the sound. • If you set the unit to the standby mode, the adjustments you made will be restored to the previous statuses.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Web Setup Menu operations You can make the settings for the network function of this unit using an Internet browser on a PC, smartphone, etc. on the remote controller to display the Setup menu. 1. Press 2. Select "6. Hardware" - "Network" with the cursors, and then take a note of the IP address displayed in "IP Address". 3. Start the Internet browser on your PC, smartphone, etc. and enter the IP address of this unit in the URL field. 4.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Initial Setup with Auto Start-up Wizard Operations TV’s REMOTE INPUT Inputs TV HDMI 1 HDMI 2 HDMI 3 TV When you turn the unit on for the first time after purchase, the Initial Setup screen is automatically displayed on the TV to allow you to make settings required for startup using simple operations following on-screen guidance. 1. Switch the input of the TV to the input connected to the unit. 2. Put batteries into the remote controller of this unit. 3.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 1. Speaker Setup 1. Select the connected speaker configuration and press Enter. Note that the image on the screen changes each time you select the number of channels in "Speaker Channels". Speaker Setup Speaker Channels Subwoofer 7.1.2 ch < > 2ch Height 1 Speaker Top Middle Height 2 Speaker --- Zone Speaker No Zone 2 Preout Zone 2 Bi-Amp Set the subwoofer volume to more than half.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ 1 if the speakers are connected correctly. If there is any problem with the speaker connection, perform the connection after disconnecting the power cord. 5. Once the measurement is completed, it is possible to perform the measurement in 8 additional listening positions. To perform the measurement, select "Next" and press Enter, then follow the instructions. To not perform the measurement, select "Finish (Calculate)" and press Enter.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Troubleshooting Tuner BLUETOOTH function Network function USB storage device Wireless LAN Network ZONE B function Multi-zone function Remote Controller Display Others Before starting the procedure Problems may be solved by simply turning the power on/off or disconnecting/ connecting the power cord, which is easier than working on the connection, setting and operating procedure.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ When the unit is operating erratically Try restarting the unit Restarting this unit may solve the problem. Set the main unit to standby, then after waiting for 5 seconds or more, press and hold the On/Standby button of the main unit for at least 5 seconds, and then restart the unit. (The settings on this unit are kept.) If the problem persists after restarting the unit, unplug and plug the power cords or HDMI cable of this unit and connected devices.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Resetting the unit (this resets the unit settings to the default) If the restart of the unit does not solve the problem, reset the unit, and restore all the settings to the factory default at the time of purchase. This may solve the problem. If the unit is reset, your settings are restored to the default values. Be sure to note down your setting contents before performing the following operations. 1.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Troubleshooting Power When the power is turned on, "AMP Diag Mode" appears on the display of the main unit. • The protection circuit function may have operated. If the unit suddenly enters the standby state and "AMP Diag Mode" appears on the display of the main unit when the power is turned on again, this function is diagnosing whether or not the main unit is malfunctioning or there is an abnormality with the speaker cable connection.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ No sound from a connected player • Change the input selector on this unit to the position of the jack to which the player is connected. • Check the digital audio output setting on the connected device. On some game consoles, such as those supporting DVD, the default setting may be off. • For some DVD-Video discs, you need to select an audio output format from a menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Sound suddenly reduces • When using the unit for extended periods with the temperature inside the unit exceeding a certain temperature, the volume may be reduced automatically to protect the circuits. Sound suddenly changes • When "My Input Volume" is set, the volume is set for each input selector. Check "4. Source" - "My Input Volume" on the Setup menu ( p167).
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Video • Confirm that the connection between the output jack on the connected device and the input jack on this unit is correct. • Make sure that none of the connecting cables are bent, twisted, or damaged. • When the TV image is blurry or unclear, the power cord or connection cables of the unit may have interfered. In such a case, keep distance between TV antenna cable and cables of the unit.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Linked operation HDMI linked operation does not work with CEC-compliant devices, such as a TV • In the Setup menu of the unit, set "6. Hardware" - "HDMI" - "HDMI CEC" to "On". • It is also necessary to set HDMI linking on the CEC-compliant device. Check the instruction manual. • When connecting a Sharp brand player or recorder to the HDMI IN jacks, set "6. Hardware" - "HDMI" - "HDMI Standby Through" to "Auto" on the Setup menu.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Music playback is unavailable on the unit even after successful BLUETOOTH connection • When the audio volume of your BLUETOOTH-enabled device is set low, the audio may not be played back. Turn up the volume of the BLUETOOTH-enabled device. • Depending on the BLUETOOTH-enabled device, the Send/Receive selector switch may be equipped. Select Send mode.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Sound is interrupted when playing music files on the network server • Check if the network server meets the requirements for operation. • When the PC is serving as the network server, quit application software other than the server software (Windows Media® Player 12, etc.). • If the PC is downloading or copying large files, the playback sound may be interrupted.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Playback sound is interrupted, or communication is not possible • You may not receive radio waves due to poor radio wave conditions. Shorten the distance from the wireless LAN router, or remove obstacles to improve visibility, and connect again. Install the unit away from microwave ovens or other access points. It is recommended to install the wireless LAN router and the unit in the same room.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Display The display does not light up • When the Dimmer function is working, the display may go dim. Press the Dimmer button, and change the brightness level of the display. ( p15) ( p161) Others Strange noise can be heard from the unit • If you have connected another device to the same outlet as this unit, strange noise may occur under the influence of the device.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ Reducing the Power Consumption in Standby State When the following functions are enabled, the power consumption in standby state increases. To reduce the power consumption in standby state, check each setting and set the functions to "Off".
Contents ≫ Connections ≫ Playback ≫ Setup ≫ About HDMI Compatible functions • The eARC function is a newly added function for HDMI 2.1. This is an expanded function from the existing ARC function, and is able to send audio formats such as Dolby TrueHD and DTS-HD Master Audio that cannot be sent with the ARC function, from an eARC-compatible TV to this unit. –– ARC-supported audio formats: PCM, Dolby Digital, Dolby Digital Plus, DTS (DTS 96/24, DTS-ES, etc.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ unit must also conform to the HDCP standards. 24/25/30/50/60 Hz, 1920×1080p 24/25/30/50/60 Hz, 2560×1080p 24/25/30/50/60 Hz : RGB/YCbCr4:4:4 (8/10/12 bit), YCbCr4:2:2 (12 bit) –– 4K (3840×2160p) 24/25/30 Hz, 4K SMPTE (4096×2160p) 24/25/30 Hz : RGB/YCbCr4:4:4 (8 bit), YCbCr4:2:2 (12 bit) –– 4K (3840×2160p) 50/60 Hz, 4K SMPTE (4096×2160p) 50/60 Hz : YCbCr4:2:0 (8 bit) Supported Audio Formats 2 ch linear PCM: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ General Specifications Amplifier Section Rated Output Power (FTC) (North American) With 8 ohm loads, both channels driven, 1 kHz; rated 135 watts per channel minimum RMS power, with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ BLUETOOTH Section Communication system BLUETOOTH Specification version 4.2 Frequency band 2.4 GHz band Modulation method FHSS (Frequency Hopping Spread Spectrum) Compatible BLUETOOTH profiles A2DP 1.2 AVRCP 1.3 Supported Codecs SBC AAC Transmission range (A2DP) 20 Hz - 20 kHz (Sampling frequency 44.1 kHz) Maximum communication range Line of sight approx.
Contents ≫ Connections ≫ Playback ≫ Setup ≫ IN : 1 OUT () : 1 RS232 : 1 (Path through) IR IN : 1 (Path through) IR OUT : 1 (Path through) Maximum Video Resolution : 4k 60 Hz (YCbCr 4:4:4) Use one of the following Ethernet cables to connect.
SN 29403807A_EN (C) Copyright 2019 Onkyo & Pioneer Corporation Japan. All rights reserved. F1909-0 http://www.onkyo.
