Owner's Manual
Table Of Contents
- Front Panel
- Step 1: Connections
- Step 2: Initial Setup
- Step 3: Playing Back
- Details on AM/FM reception
- Playing Music Files on a USB Storage Device
- Listening to Internet Radio
- Playing Music with DLNA
- Playing Music Files in a Shared Folder
- Operating Music Files with the Remote Controller
- Using the Listening Modes
- Advanced Settings (Setup Menu)
- Operating Other Components with the Remote Controller
- Advanced speaker connections
- Connecting and Operating Onkyo RI Components
- Control Function between the Unit and External Component
- Firmware Update
- Troubleshooting
- Reference Information
Advanced Settings (Setup Menu)
En-32
Setting Item Default Value Setting Details
Back Right 7�0ft/2�10m Specify the distance between each speaker and
the listening position�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Back Left 7�0ft/2�10m Specify the distance between each speaker and
the listening position�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Surround Left 7�0ft/2�10m Specify the distance between each speaker and
the listening position�
Subwoofer 12�0ft/3�60m Specify the distance between each speaker and
the listening position�
● Default values vary depending on the regions�
● The speaker "Distance" may be unable to be changed depending on the settings in "Configuration" -
"Speaker Channels" / "Subwoofer"�
Level Calibration
Adjust the level of each speaker with the built-in test tone� Settings are automatically
configured if you use the Automatic Speaker Setup�
Setting Item Default Value Setting Details
Front Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Center 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Front Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Height Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Setting Item Default Value Setting Details
Height Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Surround Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Back Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Back Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Surround Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Subwoofer 0 dB Select a value between "-15 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● The speaker "Level Calibration" may be unable to be changed depending on the settings in
"Configuration" - "Speaker Channels" / "Subwoofer"�
● "Level Calibration" cannot be changed while muting is on�