DTR-30.6 Basic Manual Advanced Manual found here http://integraworldwide.com/manual/dtr306upg/adv/en.
Before Start Advanced Manual Advanced Manual is always updated with the latest information and its user friendly interface, which does not matter whether you access from PC or Smartphone, helps you to understand more deeply about the AV Receiver. Advanced Manual is consisted of the following chapters.
Step 1: Connections TV HDMI IN Personal computer HDMI OUT To use the ARC function, connect to the ARC compatible HDMI jack of the TV and make an appropriate setting on the unit. See the section 2 "2nd Step : Source Connection" of "Step 2: Setting Up". HDMI cable HDMI OUT HDMI OUT HDMI OUT Game console 1 Set-top box/Digital video recorder, etc. Connecting the TV and players Important: The power cord must be connected only after all other connections are completed.
Step 1: Connections Home on the remote controller, select "Setup" - "1. Input/ Output Assign" - "Monitor Out" and set the default value of "MAIN" to "SUB" or "MAIN+SUB". The unit supports the HDMI Through function that allows transmission from players to the TV even if the unit is in standby. You have to modify the settings to enable the input selection link with CEC compliant device, connection with ARC compatible TV, and HDMI Through function.
Step 1: Connections 2 8F Connecting speakers Surround back R/ Height R # " Front R Front L $ Speaker layout ' If there is only one surround back speaker, connect it to the BACK or HEIGHT L terminal. Center F 9 # " 79 Surround back L/ Height L & $ % 8 7 ' Subwoofer with built-in power amplifier To enjoy the Dolby Atmos listening mode, Surround back speakers or Height speakers need to be installed. The example above uses front Height speakers.
Step 1: Connections Characteristics of speaker types "# output front stereo sound. $ outputs center sounds such as dialogs and vocals. %& create back sound field. ' reproduces bass sounds and creates rich sound field. Connecting 78 speakers or 9F speakers enables playback in 7.1 ch configuration. 78 speakers improve sense of envelopment created by back sound field as well as seamlessness of back sounds, providing more natural sound experiences in the sound field.
Step 1: Connections Using Dolby Enabled Speakers 3 Network connection Other connections AM/FM antenna connections Connect the antennas to listen to AM/FM broadcast. When listening to the broadcast for the first time, adjust the antenna position and orientation to get the best reception. You can enjoy Internet radio and DLNA by connecting the unit to LAN. The unit can be connected to the router with an Ethernet cable or to the wireless LAN router with WiFi connection.
Step 2: Setting Up Important: When the unit is turned on for the first time, the setup wizard of the section 2 will automatically be launched. If you use the setup wizard to make the initial setup, connect a TV to the HDMI OUT MAIN jack of the unit via HDMI connection. 1 Turning the power on Connect the power cord to the outlet. Press zOn/Standby on the main unit or zReceiver on the remote controller to turn the unit on or to standby mode.
Step 2: Setting Up 2. After placing the microphone at the measurement 6. When the measurement is completed, the 5. Enabling HDMI Linked Operation and Other position, select "Do it Now" in the start screen and press Enter. 3. When "Please plug microphone that came in a box with AV receiver." is displayed, connect the microphone to the Setup Mic jack of the unit. measurement result is displayed. Press W/X on the remote controller to check the settings. Press Enter with "Save" selected.
Step 2: Setting Up 4th Step : Network Connection 2. Select and set the authentication method. The "Enter Password" screen, instead of the following screen, may be displayed automatically if the wireless LAN router does not have an automatic setting button. Initial Setup Network Connection Do you want to connect network connection? Wi-Fi Setup It gives you network services that our AV receiver support. If you wish to skip this step. Select the authentication method. select “No. Skip”.
Step 3: Playing Back 1 Playing the player and TV Remote controller parts name 1 1 zReceiver button: Turns the unit on or into standby 2 mode. 2 RCV button: Switches the remote controller to the mode for operating this unit. 3 9 z To control the unit: The remote controller of this unit has the remote mode function for controlling other devices. You cannot control this unit when the remote controller is in the remote mode other than RECEIVER mode (for controlling this unit).
Step 3: Playing Back Listening modes You can select a listening mode from various options such as Dolby Atmos, Dolby Digital and DTS. Select the desired mode by switching and listening actual sound in different modes. The selectable listening modes depend on the format of the input signals. Movie/TV: You can select a listening mode suitable for movies and TV programs. Music: You can select a listening mode suitable for music. Game: You can select a listening mode suitable for games.
Step 3: Playing Back 3 Connecting and playing the Bluetoothenabled device You can wirelessly enjoy music files stored in a smartphone or other Bluetooth-enabled device. The coverage area is `?* # { & The Bluetooth-enabled device needs to support the A2DP profile. Note that connection is not always guaranteed with all Bluetooth-enabled devices. Pairing Pairing is necessary when using the Bluetooth-enabled device for the first time.
Step 3: Playing Back USB: Select "USB" in the TV screen and connect a USB storage device to the USB port on the front panel. On the TV screen, select the desired folder or music file with the cursors of the remote controller and press Enter to confirm and start playback. "USB" becomes selectable after the USB function starts up even if it cannot be selected first. It may take about a minute to start up.
Step 3: Playing Back 6 Using the multi-zone function You can multi-zone connect the unit with an integrated amplifier and speakers in a separate room and play sound from an external device connected to the analog audio input jacks of the unit, sound from the "NET", "USB" or "Bluetooth" source, and the AM/FM broadcasting.
Step 3: Playing Back Performing Multi-zone Playback 1. Press Zone2 on the remote controller, point the remote controller at the unit and press zReceiver. "Z2" stays lit on the main unit display and the multi-zone function is enabled. (Zone 2 is now on.) 2. Press Zone2 on the remote controller again and press Input Selector of the input to be played in a separate room.
1 23 4 5 6 7 8 9 F G H I J K (Australian and Asian models) (Australian model) L M N O P Q R S T Front Panel 1 zOn/Standby button: Turns the unit on or into standby 2 3 4 5 6 7 8 mode. Bluetooth indicator: Flashes while pairing with a Bluetooth-enabled device is in progress and stays lit when pairing is completed. Wi-Fi indicator: Stays lit while the unit is connected to the wireless LAN router. Tone and Tone Level buttons: Adjusts the high tone and low tone.
1 2 G 3 4 H 5 I 6 7 J 8 K 9 L F M Rear Panel 1 RI REMOTE CONTROL jack: An Onkyo product with RI 2 3 4 5 6 7 jack can be connected and synchronized with this unit. : The supplied antennas are connected. COMPONENT VIDEO IN/OUT jacks: Component video input/output jacks. ETHERNET port: Used for LAN connection. RS232 port: Connected to the home control system. (¼) IR IN A/B, IR OUT jack: Connected to the multiroom remote control kit.
1 2 3 4 9 5 6 7 8 Display 1 Stays lit or flashes in the following conditions. 2 3 4 5 "Z2": Zone 2 output is on. "HDMI": HDMI signals are input and the HDMI input selector is selected. "ARC" (Audio Return Channel): Audio signals are input from the ARC compatible TV and the TV/CD input selector is selected. "3D": Input signals are 3D. "USB": "USB" input is selected and USB storage device is connected. It will flash if the USB storage device is not correctly connected.
Troubleshooting Before starting the procedure Problems may be solved by simply turning the power on/off or disconnecting/connecting the power cord, which is easier than working on the connection, setting and operating procedure. Try the simple measures on both the unit and the connected device. If the problem is that the video or audio is not output or the HDMI linked operation does not work, disconnecting/connecting the HDMI cable may solve it.
Specifications Amplifier Section Network Section z HDMI Rated Output Power All channels: 95 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) 115 watts minimum continuous power per channel, 6 ohm loads, !#$ & ' * + + + + of 0.
Others License and Trademark Information Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Surround, Surround EX and the double-D symbol are trademarks of Dolby Laboratories. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Onkyo is under license. Other trademarks and trade names are those of their respective owners.
DISCLAIMER For U.S. models Through this device you are able to link to other services or websites which are not under the control of any company which has designed, manufactured or distributed/have distributed this device, and its affiliates (collectively, “Company”). We have no control over the nature, content and availability of those services. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
Integra Division of 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu Integra Division of 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.integra.com.