Owner's Manual

Advanced Settings
28
Level Calibration
Adjust the level of each speaker with the built-in test tone. Settings are automatically
configured if you use the Automatic Speaker Setup.
Setting Item Default Value Setting Details
Front Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
Center 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
Front Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
Surround Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
Back Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
r The setting is not displayed if "Speaker
Configuration" - "Back" is set to other than
"None" and also "Back ch" is set to "1ch".
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Front Speakers Type"
is set to "Bi-Amp".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
Back Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
r The setting is not displayed if "Speaker
Configuration" - "Back" is set to other than
"None" and also "Back ch" is set to "1ch".
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Front Speakers Type"
is set to "Bi-Amp".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
Setting Item Default Value Setting Details
Back 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
r The setting is displayed if "Speaker
Configuration" - "Back" is set to other than
"None" and also "Back ch" is set to "1ch".
r This setting cannot be changed when "Speaker
Settings" - "Powered Zone 2" is set to "Yes"
and Zone 2 is turned on.
Surround Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
Subwoofer 0dB Select a value between "-15dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
Height Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Height Speakers
Type" is set to "Not Use".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
Height Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change the
value. Select the desired level.
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Height Speakers
Type" is set to "Not Use".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
r In the following cases, the settings for "Level Calibration" cannot be changed:
– The speaker is set to "No" or "None" in "Speaker Configuration".
– Mute (MUTING) is set.
r The test tone is output at the standard level for THX, which is 0dB (absolute volume setting 82). If you
normally listen at volume settings below this, be careful because the test tone will be much louder.
r If you are using a handheld sound pressure level meter, adjust the level of each speaker to 75dB SPL
at the listening position, measured in C-Weighting and slow reading.