Owner's Manual

38
En
Center
*1
, Surround
*1
, Surr Back
*2*3*
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
to 130Hz, 150Hz, 200Hz
` None:
Select if no speaker is connected.
Note
*1
Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
Surr Back Ch
` 1ch:
Select if only one surround back speaker L is con-
nected.
` 2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
•If theSurr Back” Setting is set to “None” ( 38), this setting
cannot be selected.
LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 110Hz, 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Note
If you’re using THX-certified speakers, select “80Hz”.
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
` On
:
Double Bass function on.
` Off:
Double Bass function off.
Note
This function can be set only if the “Subwoofer” setting is set to
Ye s”, and the “Front” setting is set to “Full Band”.
If you’re using THX-certified speakers, select “Off”.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
Unit
` feet
:
Distances can be set in feet. Range: 0.5ft to 30ft in
0.5 foot steps.
` meters:
Distances can be set in meters. Range: 0.15m to
9.0m in 0.15 meter steps.
Left, Center, Right, Surr Right, Surr Back Right,
Surr Back Left, Surr Left, Subwoofer
` Specify the distance from the each speaker to your lis-
tening position.:
Note
Speakers that you set to “No”or “None” in the
Speaker Configuration” cannot be selected ( 37).
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Left, Center*
1
, Right, Surr Right, Surr Back
Right, Surr Back Left, Surr Left
` –12dB to 0dB to +12dB in 1 dB step.
Subwoofer*
1
` –15dB dB to 0dB to +12dB in 1 dB step.
Note
Speakers that you set to “No”or “None” in the
“Speaker Configuration” cannot be selected ( 37).
The speakers cannot be calibrated while the AV receiver is
muted.
The test tone is output at the standard level for THX, which is 0
dB (absolute volume setting 82). If you normally listen at vol-
ume settings below this, be careful because the test tone will be
much louder.
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved
( 22).
Tip
If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
Equalizer Settings
Equalizer
` Manual:
You can adjust the equalizer for each speaker manu-
ally. If you selected “Manual”, continue with this
procedure.
This setting is set automatically by Audyssey 2EQ
®
Room Correction and Speaker Setup function ( 23).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function ( 23).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function ( 23).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function ( 23).