AV Receiver DTR-20.
Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water.
Thank you for purchasing an Integra AV receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver. Please retain this manual for future reference.
Contents Introduction Important Safety Instructions ......................................... 2 Precautions....................................................................... 3 Supplied Accessories...................................................... 4 Features ............................................................................ 6 Front & Rear Panels......................................................... 8 Front Panel.....................................................................
Features Amplifier Miscellaneous • 90 Watts/Channel @ 8 ohms (FTC) • 160 Watts/Channel @ 6 ohms (IEC) • 175 Watts/Channel @ 6 ohms (JEITA) • Optimum Gain Volume Circuitry • H.C.P.S.
*1 THX and the THX logo are trademarks of THX Ltd. which may be registered in some jurisdictions. All rights reserved. THX Select2 Plus Before any home theater component can be THX Select2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Select2 Plus logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come.
Front & Rear Panels Front Panel (North American models) (Australian and Chinese models) The page numbers in parentheses show where you can find the main explanation for each item.
Display For detailed information, see the pages in parentheses.
Rear Panel DIGITAL IN COAXIAL and OPTICAL jacks ETHERNET port Composite video and analog audio jacks (BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, PC IN, TV/CD IN) FM ANTENNA jack and AM ANTENNA terminal MONITOR OUT V jack PC IN jack PRE OUT jacks (SURROUND BACK, SUBWOOFER) COMPONENT VIDEO IN and OUT jacks HDMI IN and OUT jacks ZONE 2 PRE/LINE OUT jacks UNIVERSAL PORT jack SPEAKERS terminals (CENTER, FRONT, SURROUND) IR IN and OUT jacks 12V TRIGGER OUT jacks RS232 jack* See “Connecting t
Remote Controller Controlling the AV Receiver *1 To control the AV receiver, press Receiver to select Receiver mode. You can also use the remote controller to control Integra/Onkyo Blu-ray Disc/DVD player, CD player, and other components. See “Entering Remote Control Codes” for more details (➔ page 63). For detailed information, see the pages in parentheses.
Connections Connecting the AV Receiver Connecting Your Speakers Connecting the Speaker Cables The following illustration shows which speaker should be connected to each pair of terminals. Surround right L Surround left R AUDIO INPUT Surround back right Surround back left Power amplifier Front right Front left Center ■ 7.2-channel playback Connect your Power amplifier’s analog audio input jacks to the AV receiver’s SURROUND BACK L/R PRE OUT jacks with audio cables.
Speaker Configuration Speaker Connection Precautions The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 29) or manually (➔ page 41).
Using Dipole Speakers You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers (A) should be positioned so that their arrows point toward the TV/screen, while the surround back dipole speakers (B) should be positioned so that their arrows point toward each other, as shown.
About AV Connections Connecting AV components HDMI cable Other cables : Video & Audio AV receiver TV, projector, etc. Blu-ray Disc/ DVD player : Video : Audio AV receiver Game console TV, projector, etc. Blu-ray Disc/ DVD player • Before making any AV connections, read the manuals supplied with your AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections.
Connecting Components with HDMI VCR or DVD recorder/Digital Video Recorder Game console TV, projector, etc. Blu-ray Disc/DVD player Personal computer Satellite/cable set-top box, etc. Connect your components to the appropriate jacks. The default input assignments are shown below. ✔: Assignment can be changed (➔ page 40). Jack Input Output Components Assignable HDMI IN 1 Blu-ray Disc/DVD player ✔ HDMI IN 2 VCR or DVD recorder/Digital Video Recorder ✔ HDMI IN 3 Satellite/cable set-top box, etc.
Connecting Your Components The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings. Connect your components to the appropriate jacks. The default input assignments are shown below. See “Connection Tips and Video Signal Path” for more information (➔ page 78). ✔: Assignment can be changed (➔ page 40). No.
• With connection , if your Blu-ray Disc/DVD player connect to the main stereo. has both the main stereo and multichannel outputs, be sure to ■ How to record a video source With the connections described above, you cannot record the videos through the AV receiver. See “Recording” about connections for video recording (➔ page 38). Connecting Integra/Onkyo Components 1 Make sure that each Integra/Onkyo component is connected with an analog audio cable (connection in the hookup examples) ( ➔ page 17).
Connecting the Antennas This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Caution • Be careful not to injure yourself when using thumbtacks. Push. Insert wire. Release. North American models Insert the plug fully into the jack. Australian and Chinese models Insert the plug fully into the jack.
Turning On & Basic Operations Turning On/Off the AV Receiver On/Standby Receiver Receiver Turning On 1 Press On/Standby or on the front panel. Press Receiver followed by Receiver on the remote controller. The AV receiver comes on, the display lights. Turning Off 1 Press On/Standby or on the front panel. Press Receiver followed by Receiver on the remote controller. The AV receiver will enter standby mode.
Playback The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings. Controlling Contents of USB or Network Devices See “Controlling Other Components” about the operation of other components (➔ page 63). Press USB or NET first. This section describes the procedure for using the remote controller unless otherwise specified.
Return Playing an iPod/iPhone via USB This button returns to the previous menu. This button fast-forwards the current song. This button selects the next song. This button stops playback. This section explains how to play music files on the iPod/iPhone.
Standard Mode control Listening to vTuner Internet Radio The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller (USB). This unit includes the full vTuner Internet Radio Service at no additional charge. Once you have connected your unit to the Internet you can select vTuner Internet Radio to search for and play Internet radio stations and podcasts at any time. To enhance your Internet radio experience, the http://onkyo.vtuner.
Listening to Other Internet Radio To listen to other internet radio stations, insert the following step after step 1 in the “Listening to vTuner Internet Radio” section. 1 On your computer, start your web browser and enter the AV receiver’s IP address in the browser’s Internet address (URL) field. The browser connects to the AV receiver (WEB Setup Menu). Note • The AV receiver’s IP address is shown on “IP Address” (➔ page 54).
Windows Media Player 11 Setup Using Remote Playback This section explains how to configure Windows Media Player 11 so that the AV receiver can play the music files stored on your computer. 1 Start Windows Media Player 12. To enable remote playback, you must first configure Windows Media Player 12. 2 Press NET. The “NET” screen appears. The NET indicator lights. If it flashes, verify the network connection. 3 Use / / / to select “dlna”, and press A list of media server appears.
Listening to AM/FM Radio This section describes the procedure using the buttons on the front panel unless otherwise specified. ■ Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency. 1 On the remote controller, press Tuner repeatedly to select “AM” or “FM”, followed by D.TUN. Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.
■ Deleting Presets ■ Displaying Radio Text (RT) 1 Select the preset that you want to delete. See the previous section. 1 2 While holding down Memory, press Tuning Mode. The preset is deleted and its number disappears from the display. Using RDS (excluding North American) RDS works only in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator lights. When the station is broadcasting text information, the text can be displayed.
RDS program types (PTY) Type En 28 Display None None News reports News Current affairs Affairs Information Info Sport Sport Education Educate Drama Drama Culture Culture Science and technology Science Varied Varied Pop music Pop M Rock music Rock M Middle of the road music Easy M Light classics Light M Serious classics Classics Other music Other M Weather Weather Finance Finance Children’s programmes Children Social affairs Social Religion Religion Phone in Pho
Using Basic Functions Using the Automatic Speaker Setup With the supplied calibrated microphone, Audyssey 2EQ® automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey 2EQ then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain.
4 Press Enter. Audyssey 2EQ® Room Correction and Speaker Setup starts. Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup. If you select “Audyssey Quick Start”, you will go to step 7.
Changing the Speaker Setup Manually You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup. See also: • “Speaker Configuration” (➔ page 41) • “Speaker Distance” (➔ page 42) • “Level Calibration” (➔ page 43) • “Equalizer Settings” (➔ page 43) Note • Please note that THX recommends any THX main speakers be set to “80Hz(THX)”.
Using the Listening Modes Selecting Listening Modes See “About Listening Modes” for detailed information about the listening modes (➔ page 33). ■ Listening Mode Buttons Press Receiver first. Movie/TV, Music, Game Music Movie/TV Game THX Movie/TV button This button selects the listening modes intended for use with movies and TV. Game button This button selects the listening modes intended for use with video games. Music button This button selects the listening modes intended for use with music.
About Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. ■ Explanatory Notes Front speakers Center speaker S urround speakers S urround back speakers S ubwoofers Input Source The following audio formats are supported by the listening mode. This is mono (monophonic) sound. This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers.
■ Onkyo-Original DSP Listening Modes Listening Mode Description Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.
Listening Mode Description Input Source Speaker Layout Dolby Pro Logic IIx*1 Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience Dolby Pro Logic II that fully envelops the listener. As well as music and movies, video games PL Mo v i e can also benefit from the dramatic spatial effects and vivid imaging.
Listening Mode Description THX Founded by George Lucas, THX develops stringent standards that ensure movies are reproduced in movie theaters and home theaters just as the director intended. THX Modes carefully optimize the tonal and spatial characteristics of the soundtrack for reproduction in the home-theater environment. They can be used with 2-channel matrixed and multichannel sources. Surround back speaker output depends on the source material and the selected listening mode.
Using the Home Menu Note *1 The Home menu provides you quick access to frequently used menus without having to go through the long standard menu. This menu enables you to change settings and view the current information. The Home menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings. 1 2 Press Receiver followed by Home. The Home menu will be superimposed on the TV screen.
Displaying Source Information You can display various information about the current input source as follows. (Components connected to the UNIVERSAL PORT jack are excluded.) 1 Muting the AV Receiver You can temporarily mute the output of the AV receiver. 1 Press Receiver followed by Display repeatedly to cycle through the available information. Press Receiver followed by Muting. The output is muted and the MUTING indicator flashes on the display. Tip • To unmute, press Muting again or adjust the volume.
Advanced Operations Advanced Setup On-screen Setup Menus Common Procedures in Setup Menu The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the composite video MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings. Remote indicator Receiver This section describes the procedure for using the remote controller unless otherwise specified. / // Enter MENU 1. 2. 3. 4. 5. 6. 7. 8. 9.
Input/Output Assign Main Menu Input/Output Assign Monitor Out You can specify the output resolution for the HDMI OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV. ■ Resolution `Through: Select this to pass video through the AV receiver at the same resolution and with no conversion. `Auto: Select this to have the AV receiver automatically convert video at resolutions supported by your TV.
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TV/CD, PORT ` IN1, IN2: Select a corresponding component video input to which the video component has been connected. ` - - - - -: Select if you are using the HDMI output, not the component video output, to output composite video and component video sources. Note • If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the “PORT” selector.
■ Subwoofer `Yes `No ■ Front `Full Band `40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz Note • If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”. ■ Center, Surround `Full Band `40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz ` None ■ Double Bass This setting is NOT set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 29).
■ Left, Center, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer ` Specify the distance from each speaker to your listening position. Note • These settings are not available in either of the following cases: – a pair of headphones is connected. – the “Audio TV Out” setting is set to “On” (➔ page 53). – “HDMI Control (RIHD)” is set to “On” (➔ page 52) and you’re listening through your TV speakers.
■ BGC `Off `On You can apply THX’s Boundary Gain Compensation (BGC) to compensate the perceived exaggeration of low frequencies for listeners sitting very close to a room boundary (i.e., wall). Audio Adjust Main menu Audio Adjust With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. Multiplex/Mono Note • This setting is only available if “THX Ultra2/Select2 Subwoofer” is set to “Yes”.
Dimension ` –3 to 0 to +3 With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.
Source Setup Items can be set individually for each input selector. Preparation Press the input selector buttons to select an input source. Main menu Source Setup Audyssey The tone for each speaker is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup (➔ page 29). ■ Audyssey `Off `Movie: Select this setting for movie material. The Audyssey indicator lights.
IntelliVolume Note • If you want to use Audyssey Dynamic EQ or Dynamic Volume with THX listening modes, set the “Loudness Plus” setting to “Off” and set “Preserve THX Settings” to “No” (➔ page 44). • If you make Dynamic Volume active, “Dynamic EQ” is set to “On”. The Dynamic Vol indicator will light. • When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is automatically switched to “Off”. • These technologies cannot be used when: – a pair of headphones is connected, or – Direct listening mode is selected.
Picture Adjust Name input area BD/DVD 4 - 4. Name Edit Name a n b o 1 { 2 } +10 A N ! [ B O @ ] c p d q e r f s g t h u 3 4 | : Shift 5 6 < 7 > – 8 9 0 ? Space OK Back Space Shift C P # j w CLR D Q $ ; E R % ’ F S ^ , G T & . Shift +10 i v Shift H U I V ( k x l y ` All Erase J W ) K L X Y _ / Space Back Space OK CLR m z Using Picture Adjust, you can adjust the picture quality and reduce any noise appearing on the screen.
■ Game Mode*3*4*5 ` Off ` On If video signal delay occurs during playback on a video component (i.e., game console), select the corresponding input source and set the “Game Mode” setting to “On”. The delay will decrease but in return the picture quality will become poor. ■ Film Mode*3*5*6 ` Video: “Film Mode” detection is not applied and the input signal is handled as a video source. ` Auto: Detects whether the input signal is a video or a movie. If it is a movie, the appropriate conversion is applied.
■ Fixed Mode ` Off: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. `PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced. `DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.
■ DTS/DTS-ES/DTS-HD With this setting, you can specify the listening mode used when DTS or DTS-HD High Resolution format digital audio signals are played (DVD, LD, CD, etc.). Specifies the default listening mode for DTS-HD Master Audio sources, such as Blu-ray or HD DVD (input via HDMI). ■ Other Multich Source Specifies the default listening mode for multichannel PCM sources from HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD.
Hardware Setup Main menu Hardware Setup Remote ID ■ Remote ID `1, 2, or 3 When several Integra/Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from “1”, to “2” or “3”. Note • If you do change the AV receiver’s remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.
■ HDMI Through ` Off ` Auto: Detects the signal and automatically selects the input source. ` BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TV/CD, PORT: Selects the input source for which the HDMI Through function is enabled. ` Last: The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode.
Network After modifying the network settings, you must confirm the changes by executing “Save”. This section explains how to configure the AV receiver’s network settings manually. If your router’s DHCP server is enabled, you don’t need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e., DHCP is set to “Enable”).
Remote Controller Setup Main menu Remote Controller Setup Remote Mode Setup See “Looking up for Remote Control Code” (➔ page 63). Lock Setup With this preference, you can protect your settings by locking the setup menus. Main menu Lock Setup ■ Setup ` Locked ` Unlocked When “Locked” is selected, the setup menus will be locked and you cannot change any setting. Using the Audio Settings You can change various audio settings from the Home menu (➔ page 37). 1 2 Press Receiver followed by Home.
Note • The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options. • The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD. • The Late Night function is set to “Off” when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to “Auto”.
Zone 2 In addition to the main listening room, you can also enjoy playback in another room, which we call Zone 2. For either of the rooms, you can specify a different input source. Making Zone 2 Connections Connecting the Zone Speakers to an Additional Amplifier Controlling Zone 2 Components ■ Operating on the AV receiver Zone 2 Off Tone +, – Input selector buttons This setup allows 5.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2.
Adjusting the Volume for Zone 2 ■ Operating on the remote controller 1 2 Press Zone2. Use VOL / to adjust the volume. ■ Operating on the AV receiver 1 Use Zone 2 Level /. Muting Zone 2 Using the 12V Triggers The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source.
Using the Remote Controller in Zone 2 and Multiroom Control Kits To control the AV receiver with the remote controller while you’re in the Zone 2 room, you’ll need a commercially available multiroom remote control kit. Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s installed inside a cabinet.
Controlling Other Components iPod/iPhone Playback via Onkyo Dock Using the Onkyo Dock The Dock is sold separately. Models sold are different depending on the region. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.
■ Status Messages If either of the following messages is not displayed on the AV receiver’s display, check the connection to your iPod/iPhone. • PORT Reading The AV receiver is checking the connection with the dock. • PORT Not Support The AV receiver do not support the connected dock. • PORT UP-A1 UP-A1 Dock is connected. Note • The AV receiver displays the message “UP-A1” for several seconds after recognizing the UP-A1.
✔: Available buttons Press the appropriate Remote Mode first. Buttons ✔ Top Menu*1 ✔*2 Enter / //, Dock UP-A1 Dock Onkyo Dock ✔ ✔ ✔ ✔ ✔ Repeat ✔ ✔ Random ✔ ✔ Playlist / , , , , , , ✔ Source*3 Display*4 ✔ ✔ Muting ✔ ✔ Album +/– ✔ ✔ VOL / ✔ ✔ Return ✔ Mode ✔*5 ✔ Menu ✔*6 • With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected. • For detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock.
Controlling Other Components You can use the AV receiver’s remote controller to control your other AV components, including those made by other manufacturers. This section explains how to enter the remote control code (with the default underlined) for a component that you want to control: DVD, TV, CD, etc. 7 Use / to select a brand, and then press Enter. A remote control code with its instructions are displayed. Follow the procedure.
Remote Control Codes for Integra/Onkyo Components Connected via Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 Make sure the Integra/Onkyo component is connected with an cable and an analog audio cable (RCA). See “Connecting Integra/Onkyo Components” for details (➔ page 18).
✔: Available buttons Press the appropriate Remote Mode first.
Appendix Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased this unit. To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press On/Standby .
■ Only the front speakers produce sound ■ Can’t get 6.1/7.1 playback When the Stereo or Mono listening mode is selected, — only the front speakers and subwoofer produce sound. In the Mono listening mode, only the front speakers 44 output sound if the “Output Speaker” setting is set to “Left / Right”. Check the Speaker Configuration.
Video Remote Controller ■ The remote controller doesn’t work ■ There’s no picture Make sure that all video connecting plugs are pushed 15 in all the way. 16, 17 Make sure that the batteries are installed with the correct polarity. 4 If your TV is connected to the HDMI OUT, select “- - - - -” in the “HDMI Input” setup to watch composite video, and component video sources. 40 Install new batteries. Don’t mix different types of batteries, or old and new batteries.
UP-A1 Dock for iPod/iPhone Zone 2 ■ There’s no sound ■ There’s no sound Make sure your iPod/iPhone is actually playing. — Make sure your iPod/iPhone is properly inserted in the Dock. — Make sure the UP-A1 Dock is connected to the UNIVERSAL PORT jack on the AV receiver. — Make sure the AV receiver is turned on, the correct — input source is selected, and the volume is turned up. Make sure the plugs are pushed in all the way. — Try resetting your iPod/iPhone.
Others ■ Standby power consumption In the following cases, the power consumption in 17, 52, standby mode may reach up to a maximum of 43 W: 54 – You are using the Universal Port jack. – “Network Control” is set to “Enable” in the “Network” setting. – “HDMI Control (RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter standby mode as usual.) – The “HDMI Through” setting is set to other than “Off”.
Important Note Regarding Video Playback The AV receiver can upconvert component video and composite video sources for display on a TV connected to the HDMI OUT. However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether. In this case, try the following: 1 If the video source is connected to a component video input, connect your TV to the COMPONENT VIDEO OUT.
Network/USB Features Connecting to the Network Network Requirements The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in. Internet radio Modem WAN LAN Computer or media server Router ■ Ethernet Network For the best results, a 100Base-TX switched Ethernet network is recommended.
Server Requirements ■ Server playback The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Player 12 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site.
Supported Audio File Formats For server playback and playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback time may not be display correctly. ■ LPCM (Linear PCM) • Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. • Quantization bit: 8 bit, 16 bit, 24 bit * Only for playback via network.
Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully. ■ Update via network You need a wired Internet connection to update the firmware. ■ Update via USB storage (➔ page 76) Please prepare a USB storage device such as a USB flash memory stick.
7 Using On/Standby on the front panel, turn off and on the AV receiver. Do not use Receiver on the remote controller. Congratulations! You now have the latest firmware installed on your Integra AV receiver. Troubleshooting Case 1: If “No Update” is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further. Case 2: If an error occurs, “Error!! *-** No media” is displayed on the front display of the AV receiver.
8 9 10 11 12 13 Select “Hardware Setup” and press Enter. Select “Firmware Update” and press Enter. Select “Via USB” and press Enter. Select “Update” and press Enter. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the front display of the AV receiver. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.
Connection Tips and Video Signal Path The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.
Audio Connection Formats Audio components can be connected by using any of the following audio connection formats: analog, optical, coaxial, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog VCR/DVR OUT. Audio Signal Flow Chart Blu-ray Disc/DVD player, etc.
About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Using an RIHD-compatible TV, Player, or Recorder , which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than -compatible components cannot be guaranteed.
■ How to connect and setup 1 3 Confirm the connecting and setting. 1. Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary (➔ page 53).
Specifications Amplifier Section General Rated Output Power All channels: Power Supply (North American) 90 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) 110 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.
Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver.
Memo En 85
Memo En 86
Memo En 87
Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/ Integra Division of ONKYO CHINA PRC 1301, 555 Tower, No.