AV Receiver DTR-20.
Safety Information and Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Safety Information and Introduction Precautions 5. Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss. 6. Batteries and Heat Exposure Warning Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like. 7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp.
Safety Information and Introduction Supplied Accessories Make sure you have the following accessories: Indoor FM antenna (➔ page 17) ■ Aiming the remote controller To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.
Safety Information and Introduction Table of Contents Safety Information and Introduction Important Safety Instructions ......................................2 Precautions ...................................................................3 Supplied Accessories...................................................4 Table of Contents..........................................................5 Features .........................................................................6 Front & Rear Panels.................
Safety Information and Introduction Features Amplifier • 80 Watts/Channel @ 8 ohms (FTC) • 130 Watts/Channel @ 6 ohms (IEC) • 160 Watts/Channel @ 6 ohms (JEITA) • Optimum Gain Volume Circuitry • H.C.P.S. (High Current Power Supply) Massive High Power Transformer Processing • Incorporates Qdeo™ technology for HDMI Video Upscaling (to 4K Compatible) • HDMI (Audio Return Channel, 3D, DeepColor, x.v.
Safety Information and Introduction Front & Rear Panels Front Panel (North American models) For detailed information, see the pages in parentheses.
Safety Information and Introduction Display s For detailed information, see the pages in parentheses. Z2 (Zone 2) indicator (62) 3D indicator This lights when a 3D input signal is detected.
Safety Information and Introduction Rear Panel DIGITAL IN COAXIAL and OPTICAL jacks USB port Composite video and analog audio jacks (BD/DVD IN, CBL/SAT IN, GAME IN, PC IN, TV/CD IN) ETHERNET port MONITOR OUT V jack FM ANTENNA jack and AM ANTENNA terminal ZONE 2 PRE/LINE OUT jacks HDMI IN and OUT jacks PRE OUT jacks (SURR BACK or FRONT HIGH, SUBWOOFER) COMPONENT VIDEO IN and OUT jacks RS232 jack Terminal for control.
Safety Information and Introduction Remote Controller Controlling the AV Receiver *1 To control the AV receiver, press Receiver to select Receiver mode. You can also use the remote controller to control Integra/Onkyo Blu-ray Disc/DVD player, CD player, and other components. See “Entering Remote Control Codes” for more details (➔ page 68). For detailed information, see the pages in parentheses.
Connections Connecting the AV Receiver Surround right Surround left Connecting Your Speakers Speaker Configuration The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 30) or manually (➔ page 48).
Connections Attaching the Speaker Cable Labels The speaker terminals are color-coded for identification purpose. Speaker Color Front left, Front high left White Front right, Front high right Red Center Green Surround left Blue Surround right Gray Surround back left Brown Surround back right Tan The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the table above.
Connections ■ Analog audio (RCA) Analog audio connections (RCA) carry analog audio. AV Cables and Jacks About AV Connections ■ HDMI HDMI connections can carry digital video and audio. Connecting AV components a HDMI cable Red : Video & Audio TV, projector, etc. *1 ■ Component video Component video separates the luminance (Y) and color difference signals (PB, PR), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently).
Connections Connecting Components with HDMI Satellite/cable set-top box, etc. Personal computer TV, projector, etc. Blu-ray Disc/DVD player Game console * * If your TV doesn’t support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver.
Connections Connecting Your Components The on-screen menus appear only on a TV that is connected to HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings. No. Jack/Port ✔: Assignment can be changed (➔ page 47). No. Jack/Port USB*1 Components AUDIO IN BD/DVD IN Blu-ray Disc/DVD player CBL/SAT IN Satellite/cable set-top box, etc.
Connections Connecting Integra/Onkyo RI Components 1 Make sure that each Integra/Onkyo component is connected with an analog audio cable (connection in the hookup examples) (➔ page 15). 2 3 Make the connection (see the illustration). If you’re using an RI Dock, or cassette tape deck, change the Input Display (➔ page 39). With (Remote Interactive), you can use the following special functions: e.g.
Connections Connecting the Antennas Connecting the Power Cord This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. North American models 1 Connect the supplied power cord to the AV receiver’s AC INLET. Australian models To AC wall outlet Push. Insert wire. Release. Insert the plug fully into the jack.
Turning On & Basic Operations Turning On/Off the AV Receiver Turning On 1 On/Standby Press or On/Standby on the front panel. Press Receiver followed by Receiver on the remote controller. The AV receiver comes on and its display lights. Turning Off 1 Press or On/Standby on the front panel. Press Receiver followed by Receiver on the remote controller. The AV receiver will enter standby mode.
Turning On & Basic Operations Initial Setup This section explains the settings that we recommend you to make before using the AV receiver for the very first time. A setup wizard is launched upon first-time use to let you perform those settings. Selecting the Language for the Onscreen Setup Menus This step determines the language used for the onscreen setup menus. See “Language” in “OSD Setup” (➔ page 57). Tip The on-screen menus appear only on a TV that is connected to HDMI OUT.
Turning On & Basic Operations Source Connection This step checks the connection of source components. 1 Use / to select one of the following options, and then press Enter. `Yes, Continue: Performs the checkings. `No, Skip: Skips this step and continues to “Remote Mode Setup”. 2 Select the input selector for which you want to check the connection and press Enter. The picture of the corresponding source should appear on screen with a verification prompt.
Turning On & Basic Operations Playback The on-screen menus appear only on a TV that is connected to HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.
Turning On & Basic Operations Controlling Contents of USB or Network Devices Press USB or NET first. Top Menu This button displays the top menu for each media or service. This button stops playback. / and Enter Mode These buttons navigate through the menus. You can switch between Standard Mode and Extended Mode. / This button cycles through pages. Random This button performs random playback. Playlist / In Standard Mode (iPod/iPhone), this button selects playlists. This button starts playback.
Turning On & Basic Operations Understanding Icons on the Display This section describes icons that appear on the AV receiver’s display during media playback. Icon Playing an iPod/iPhone via USB 3 A list of your iPod/iPhone model’s contents appears. The on-screen menus appear only on a TV that is connected to HDMI OUT. Tip Description Pause This section explains how to play music/video files on the iPod/iPhone.
Turning On & Basic Operations Extended Mode (Music) Control The music content information is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing. Note Playing a USB Device Listening to vTuner Internet Radio The on-screen menus appear only on a TV that is connected to HDMI OUT. You need to connect the AV receiver to your home network (➔ page 87).
Turning On & Basic Operations ■ Adding vTuner Internet Radio Stations to Favorites There are two ways you can register specific Internet radio stations (programs) from the vTuner Internet Radio. Adding to My Favorites The selected program will be added to “My Favorites” on the network service screen, which appears when pressing NET on the remote controller. 1. Press Menu with the station selected or while a station is playing. 2. Use / to select “Add to My Favorites”, and press Enter. 3.
Turning On & Basic Operations Playing Music Files on a Server Remote Playback You need to connect the AV receiver to your home network (➔ page 87). The on-screen menus appear only on a TV that is connected to HDMI OUT. You need to connect the AV receiver to your home network (➔ page 87). The on-screen menus appear only on a TV that is connected to HDMI OUT.
Turning On & Basic Operations 5 Click “OK” to close the dialog box. This completes the Windows Media Player 12 configuration. You can now play the music files in your Windows Media Player 12 library. The volume value of the remote window and the volume value of the AV receiver may not always match. Adjustments you make to the volume in the AV receiver will not be reflected in the “Remote playback” window. Tip • On the “Stream” menu, confirm that “Allow remote control of my Player...” is checked.
Turning On & Basic Operations ■ Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency. 1 4 On the remote controller, press AM or FM to select “AM” or “FM”, followed by D.TUN. Press Memory again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations. ■ Selecting Presets (Actual display depends on the country.
Turning On & Basic Operations ■ Finding Stations by Type (PTY) RDS program types (PTY) You can search for radio stations by type. Type Display 1 2 3 4 None None Press RT/PTY/TP twice. The current program type appears on the AV receiver’s display. News reports News Current affairs Affairs Information Info Use Preset / to select the type of program you want. See the table shown later in this chapter. Sport Sport To start the search, press Enter.
Turning On & Basic Operations Using Basic Functions Using the Automatic Speaker Setup With the supplied calibrated microphone, Audyssey 2EQ® automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position.
Turning On & Basic Operations 1 2 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected. 5 Set the speaker setup microphone at the Main Listening Position , and connect it to the Setup Mic jack. Setup Mic jack Speaker setup microphone 6 The speaker setting menu appears. Note • The on-screen menus appear only on a TV that is connected to HDMI OUT.
Turning On & Basic Operations Error Messages Changing the Speaker Setup Manually While Audyssey 2EQ® Room Correction and Speaker Setup is in progress, one of the error messages below may appear. You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup. See also: • “Speaker Configuration” (➔ page 48) • “Speaker Distance” (➔ page 49) • “Level Calibration” (➔ page 49) 2EQ: Auto Setup AUDYSSEY Ambient noise is too high.
Turning On & Basic Operations Using the Listening Modes Selecting Listening Modes See “About Listening Modes” for detailed information about the listening modes (➔ page 34). ■ Listening Mode Buttons Press Receiver first. Movie/TV, Music, Game Movie/TV button This button selects the listening modes intended for use with movies and TV. Music button This button selects the listening modes intended for use with music. Game button This button selects the listening modes intended for use with video games.
Turning On & Basic Operations About Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. ■ Explanatory Notes Input Source The following audio formats are supported by the listening modes. This is mono (monophonic) sound. This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers. This is 5.1-channel surround sound.
Turning On & Basic Operations ■ Onkyo-Original DSP Listening Modes Listening Mode Description Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.
Turning On & Basic Operations ■ Listening Modes Listening Mode Description Direct In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via the audio setup is disabled. See “On-screen Setup” for more details (➔ page 41).
Turning On & Basic Operations Listening Mode Description Dolby Pro Logic IIx*6 Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides Dolby Pro Logic II a very natural and seamless surround-sound PL Mo v i e experience that fully envelops the listener. As well as music and movies, video games PL Mu s i c can also benefit from the dramatic spatial effects and vivid imaging.
Turning On & Basic Operations Using the Home Menu The Home menu provides quick access to frequently used menus. The Home menu appears only on a TV that is connected to HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings. 1 2 Press Receiver followed by Home. The Home menu will be superimposed on the TV screen. Use / or / and Enter to make the desired selection. Press Home to close the menu.
Turning On & Basic Operations With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. You can display various information about the current input source as follows. 1 1 Press Receiver once followed by Sleep repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator lights on the AV receiver’s display when the sleep timer has been set.
Turning On & Basic Operations Muting the AV Receiver You can temporarily mute the output of the AV receiver. 1 Press Receiver followed by Muting. The output is muted and the MUTING indicator flashes on the AV receiver’s display. Tip • To unmute, press Muting again or adjust the volume. • Muting is automatically cancelled when the AV receiver is set to standby. Using Headphones 1 Connect a pair of stereo headphones with a standard plug (1/4 inch or 6.3 mm) to the Phones jack.
Advanced Operations On-screen Setup ■ Input `You can select input sources and view the following information: the name of input selectors, input assignments, radio information, and ARC function setting. In addition, previews of the video streams coming from HDMI inputs (HDMI IN 1/2/3/4/5) are displayed.*1 “EXTRA1” and “EXTRA2” can only be selected if they are assigned to HDMI, component, composite, coaxial, or optical inputs. Use / to select an input source and view the related information.
Advanced Operations Note *1 *2 *3 *4 • The video preview is not displayed when: – HDMI IN 6/7 is the current HDMI input source, or – No signal is present on the current input source. • The video of the currently-selected input is displayed on the main screen, not on a preview thumbnail. Only when you have selected “Custom” in the “Picture Mode” (➔ page 54), pressing Enter allows you to adjust the following items via the Quick Setup: “Brightness”, “Contrast”, “Hue” and “Saturation”.
Advanced Operations Late Night Music Optimizer CinemaFILTER ■ Late Night For Dolby Digital and Dolby Digital Plus sources, the options are: ` Off ` Low: Small reduction in dynamic range. ` High: Large reduction in dynamic range. ■ Music Optimizer ` Off ` On The Music Optimizer function enhances the sound quality of compressed music files. When set to “On”, the M.Opt indicator lights on the AV receiver’s display.
Advanced Operations ■ Screen Saver If there is no video signal on the current input source and no operation for a specific time (three minutes by default), a screen saver automatically comes on. Using the Setup Menu (Home) Remote indicator Explanatory Notes Main Menu Speaker Setup Speaker Configuration Tip • The time until the screen saver activates itself can be changed in the “Screen Saver” setting (➔ page 57). • The screen will return to its previous state if the AV receiver is operated.
Advanced Operations About the Hybrid Standby indicator By way of optimized circuitry, this function reduces power consumption when the AV receiver is in standby mode. The Hybrid Standby indicator will light in either of the following conditions: – “HDMI Through” is enabled (the HDMI indicator is off). – “Network Standby” is enabled (the NET indicator is off).
Advanced Operations HDMI Input Input/Output Assign 1 2 Main Menu 3 4 “Setup” 5 Input/Output Assign Monitor Out ■ Resolution ` Through: Select this to pass video through the AV receiver at the same resolution and with no conversion. ` Auto: Select this to have the AV receiver automatically convert video at resolutions supported by your TV. ` 480p (480p/576p), 720p, 1080i, 1080p: Select the desired output resolution. ` 1080p/24: Select this for 1080p output at 24 frames per second.
Advanced Operations Component Video Input Composite Video Input Digital Audio Input If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign “IN2” to the “BD/DVD” input selector. Here are the default assignments. If you connect a component to a composite video input, you must assign that input to an input selector.
Advanced Operations Speaker Setup 1 2 Main menu Note 3 4 “Setup” 5 Speaker Setup Some of the settings in this section are set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 30). Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup function.
Advanced Operations Speaker Distance This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 30). Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended. ■ Unit ` feet: Distances can be set in feet. Range: 0.2ft to 30.0ft in 0.2 foot steps. ` meters: Distances can be set in meters. Range: 0.06m to 9.00m in 0.06 meter steps.
Advanced Operations Dolby ■ PL IIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If you’re not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx. Panorama ` On ` Off With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.
Advanced Operations Theater-Dimensional Source Setup ■ Listening Angle ` Wide: Select if the listening angle is greater than 30 degrees. ` Narrow: Select if the listening angle is less than 30 degrees. With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position.
Advanced Operations Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater system each speaker level must be adjusted so that –30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey 2EQ® will play at reference level when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers heard it.
Advanced Operations Name Edit You can enter a custom name for each individual input selector and radio preset for easy identification. When entered, the custom name will appear on the display. The custom name is edited using the keyboard screen. ■ Name 1 Use / / / to select a character, and then press Enter. Repeat this step to enter up to 10 characters. 2 To store a name when you’re done, be sure to select “OK” by using / / / , and then press Enter. Space: Enters a space character.
Advanced Operations ■ Picture Mode*1 ` Custom: All settings can be performed manually. ` Cinema: Select when the picture source is a movie or alike. ` Game: Select when the video source is a game console. ` Through: Does not adjust picture quality (changes resolution). ` Direct: Does not adjust picture quality (does not change resolution). The video coming from an analog input and output by HDMI OUT is processed in the same way as “Through”.
Advanced Operations Audio Selector ■ Audio Selector ` ARC: The audio signal from your TV tuner can be sent to HDMI OUT of the AV receiver.*1 With this selection, the TV’s audio can be automatically selected as a priority among other assignments. ` HDMI: This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is automatically selected as a priority.
Advanced Operations 2 Use / to select the signal format that you want to set, and then use / to select a listening mode. Only listening modes that can be used with each input signal format can be selected (➔ pages 33 to 37). The “Last Valid” option means that the listening mode selected last will be used. The “Straight Decode” option means that straight decoding listening mode (Dolby Digital, DTS, etc.) is selected. Note • For the “AM” or “FM” input selector, only “Analog” will be available.
Advanced Operations OSD Setup 12V Trigger A/B/C Setup ■ On Screen Display ` On ` Off This preference determines whether operation details are displayed on-screen when an AV receiver function is adjusted. Even when “On” is selected, operation details may not be output if the input source is connected to an HDMI IN. Depending on their type, when some components are turned by using triggers A, B, and C, a large amount of current may be drawn at once.
Advanced Operations Hardware Setup 1 2 Main Menu 3 4 “Setup” 5 Hardware Setup Multi Zone ■ Zone 2 Out ` Fixed: The Zone 2 volume must be set on the amp in that zone. ` Variable: The Zone 2 volume can be set on the AV receiver. If you’ve connected your Zone 2 speakers to an amp with no volume control, set the “Zone 2 Out” setting, to “Variable” so that you can set the volume, balance, and tone of zone 2 on the AV receiver.
Advanced Operations ■ HDMI Through ` Off ` BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD, EXTRA1, EXTRA2: Selects the input source for which the HDMI Through function is enabled. ` Last: The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode.
Advanced Operations ■ InstaPrevue These settings apply to “InstaPrevue” of the Home menu (➔ page 38) and specify the preview display of HDMI video streams. Sub Window ` Multi: Displays preview thumbnails all at once. ` Single: Displays preview thumbnails one-by-one. With this setting, you can set the number of preview thumbnails displayed.
Advanced Operations ■ Network Standby ` On ` Off This setting enables or disables control over the network. When enabled, the NET indicator will be dimly-lit while the AV receiver is in standby mode. Note that the indicator may not light under certain conditions (➔ page 45). Note • When set to “On”, the power consumption slightly increases in standby mode. ■ Update Notice ` Enable ` Disable When this setting is enabled, you will be notified if a firmware update via network is available.
Advanced Operations Zone 2 change the setting so that you can set the Zone 2 volume on the AV receiver. See “Multi Zone” (➔ page 58). In addition to the main listening room, you can also enjoy playback in another room, or as we call Zone 2. And, you can select a different source for each room. Setting the Zone 2 Out Making Zone 2 Connections Connecting the Zone Speakers to an Additional Amplifier This setup allows 5.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2.
Advanced Operations Adjusting the Volume for Zone 2 ■ Operating on the remote controller 1 2 Press Zone2. Use VOL / . ■ Operating on the AV receiver 1 Use Zone 2 Level / . Adjusting the Tone and Balance of Zone 2 1 2 On the AV receiver, press Zone 2. 3 Use –/+ to adjust the bass, treble or balance. • You can boost or cut the bass or treble from –10 dB to +10 dB in 2 dB steps. • You can adjust the balance from 0 in the center to +10 dB to the right or +10 dB to the left in 2 dB steps.
Advanced Operations Using the Remote Controller in Zone 2 and Multiroom Control Kits To control the AV receiver with the remote controller while you’re in the Zone 2 room, you’ll need a commercially available multiroom remote control kit. Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s installed inside a cabinet.
Controlling Other Components iPod/iPhone Playback via Onkyo Dock Using the Onkyo Dock The Dock is sold separately. Models sold are different depending on the region. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.
Controlling Other Components Controlling Your iPod/iPhone By pressing the Remote Mode button that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section. See “Entering Remote Control Codes” for details on entering a remote control code (➔ page 68). See the Dock’s instruction manual for more information. ■ Press the appropriate Remote Mode button first.
Controlling Other Components Controlling Other Components You can use the AV receiver’s remote controller to control your other AV components. This section explains how to enter the remote control code for a component that you want to control: DVD, TV, CD, etc. Preprogrammed Remote Control Codes The following Remote Mode buttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components.
Controlling Other Components Entering Remote Control Codes Remapping Colored Buttons You’ll need to enter a code for each component that you want to control. You can change the configuration of colored buttons, with which Remote Mode buttons are preset. 1 Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized by category (e.g., DVD player, TV, etc.).
Controlling Other Components ` 70868: Onkyo MD recorder without ` 71323: Onkyo CD recorder without ` 82990: Onkyo Dock without Remote Control Codes for Integra/Onkyo Components Connected via RI Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.
Controlling Other Components Controlling a Blu-ray Disc/DVD Player, HD DVD Player or DVD Recorder ■ TV operation Press the appropriate Remote Mode button first. Available buttons , Input, TV VOL Muting BD/DVD is preprogrammed with the remote control code *1 for controlling a component that supports the (limited to some models). The component must be able to receive remote control commands via and be connected to the AV receiver via HDMI.
Controlling Other Components Press the appropriate Remote Mode button first.
Appendix Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased this unit. To reset the AV receiver to its factory defaults, turn it on and, while holding down CBL/SAT, press On/Standby.
Appendix If the input signal format is set to “PCM” or “DTS”. 55 Set it to “Off”. ■ Only the front speakers produce sound When the Stereo or Mono listening mode is selected, 36 only the front speakers and subwoofer produce sound. ■ The subwoofer produces no sound When you play source material that contains no information in the LFE channel, the subwoofer produces no sound. — Make sure the speakers are configured correctly.
Appendix When the AV receiver is not connected to a TV via HDMI OUT, on-screen menus are not displayed. Video ■ There’s no picture Make sure that all video connecting plugs are pushed 13 in all the way. Make sure that each video component is properly connected. 14, 15 If your TV is connected to HDMI OUT, select “- - - - -” in the “HDMI Input” setup to watch composite video, and component video sources.
Appendix If you cannot operate it, you will need to enter the appropriate remote control code. 67 To control another manufacturer’s component, point 68 the remote controller at that component. To control an Integra/Onkyo component that’s 69 connected via , point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first. To control an Integra/Onkyo component that’s not connected via , point the remote controller at the component.
Appendix ■ The USB Device Playback ■ Can’t access the music files on a USB device Make sure the USB device is plugged in properly. — The AV receiver supports USB devices that support 88 the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class. USB memory devices with security functions cannot — be played.
Appendix Important Note Regarding Video Playback The AV receiver can upconvert component video and composite video sources for display on a TV connected to HDMI OUT. However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether. In this case, try the following: 1 If the video source is connected to a component video input, connect your TV to COMPONENT VIDEO OUT.
Appendix Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully. ■ Update via network You need a wired Internet connection to update the firmware. ■ Update via USB storage (➔ page 80) Please prepare a USB storage device such as a USB flash memory stick.
Appendix Update Procedure 1 Press Receiver followed by Home on the remote controller. The Home menu appears on the TV screen. 2 Select “Firmware Update” and press Enter. Note that the “Firmware Update” option will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable. 3 Select “Update via NET” and press Enter. Note that this option will not be available if there is no firmware file newer than the currently installed version.
Appendix Updating the Firmware via USB The AV receiver allows you to update the firmware using a USB device. Note • Never unplug or turn off the AV receiver during the update process. • Never plug or unplug an HDMI cable or a USB device during the update process. • Never unplug the USB storage device containing the firmware file or the AC power cord during the update process. • Do not attempt to access the AV receiver from your PC while it is being updated.
Appendix Troubleshooting Case 1: If an error occurs, “Error!! *-**” is displayed on the AV receiver’s display. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action. ■ Errors during an update via USB The Americas Integra Division of 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 Hours: M-F 9am-8pm/Sat-Sun 10am-8pm ET http://www.integrahometheater.
Appendix Connection Tips and Video Signal Path The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen menus appear only on a TV that is connected to HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.
Appendix Audio Connection Formats Video Resolution Chart Audio components can be connected by using any of the following audio connection formats: analog, optical, coaxial, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. The following tables show how video signals at different resolutions are output by the AV receiver.
Appendix Using an RIHDcompatible TV, Player, or Recorder , which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than -compatible components cannot be guaranteed.
Appendix ■ How to connect and setup 1 2 Confirm the connection and settings. 1. Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable.
Appendix About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Appendix Network/USB Features Connecting to the Network The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in. Internet radio Modem WAN LAN Router Network Requirements ■ Ethernet Network For the best results, a 100Base-TX switched Ethernet network is recommended.
Appendix Server Requirements ■ Server playback The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Player 12 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site.
Appendix Supported Audio File Formats For server playback and playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback times may not display correctly. Note • With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis. • In the case of server playback, the above-mentioned file formats may not be played depending on the server type. ■ MP3 (.mp3 or .
Appendix License and Trademark Information “x.v.Color” is a trademark of Sony Corporation. Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
Appendix Specifications Amplifier Section Rated Output Power All channels: (North American) 80 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
Integra Division of 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu Integra Division of 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.integra.com.