Owner's Manual

Advanced Settings
26
Level Calibration
Adjust the level of each speaker with the built-in test tone. Settings are automatically
configured if you use the Automatic Speaker Setup.
Setting Item Default Value Setting Details
Front Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
Center 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
Front Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
Surround Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
Back Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
r The setting is not displayed if "Speaker
Configuration" - "Back" is set to other than
"None" and also "Back ch" is set to "1ch".
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Front Speakers
Type" is set to "Bi-Amp".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
Back Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
r The setting is not displayed if "Speaker
Configuration" - "Back" is set to other than
"None" and also "Back ch" is set to "1ch".
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Front Speakers
Type" is set to "Bi-Amp".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
Setting Item Default Value Setting Details
Back 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
r The setting is displayed if "Speaker
Configuration" - "Back" is set to other than
"None" and also "Back ch" is set to "1ch".
r This setting cannot be changed when
"Speaker Settings" - "Powered Zone2" is set
to "Yes" and Zone 2 is turned on.
Surround Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
Subwoofer 0dB Select a value between "-15dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
Height Left 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Height Speakers
Type" is set to "Not Use".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
Height Right 0dB Select a value between "-12dB" to "+12dB". A
test tone will be output each time you change
the value. Select the desired level.
r This setting cannot be changed in any of the
following cases.
– "Speaker Settings" - "Height Speakers
Type" is set to "Not Use".
– "Speaker Settings" - "Powered Zone 2" is
set to "Yes" and also Zone2 is set to on.
r In the following cases, the settings for "Level Calibration" cannot be changed:
– The speaker is set to "No" or "None" in "Speaker Configuration".
– Mute (MUTING) is set.