Owner's Manual

ManualsBrandsIntegra ManualsReceiversIntegra DTR-30.2

OSD Setup

■ On Screen Display

This preference determines whether operation details

are displayed on-screen when an AV receiver function is

adjusted.

` On

Displayed.

` Off:

Not displayed.

Even when “On” is selected, operation details may not be

output if the input source is connected to an HDMI IN.

■ TV Format (Australian models)

For the on-screen setup menus to display properly, you

must specify the TV system used in your area.

` Auto

Select this to automatically detect the TV system

from the video input signals.

` NTSC:

Select this if the TV system in your area is NTSC.

` PAL:

Select this if the TV system in your area is PAL.

■ Language

` English

, Deutsch, Français, Español, Italiano, Ned-

erlands, Svenska,

This setting determines the language used for the on-

screen setup menus.

12V Trigger A/B/C Setup

See “Using the 12V Triggers” (➔ 64).

Main menu Hardware Setup

Remote ID

■ Remote ID

` 1

, 2, or 3

When several Integra/Onkyo components are used in

the same room, their remote ID codes may overlap. To

differentiate the AV receiver from the other compo-

nents, you can change its remote ID from “1”, to “2” or

“3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Changing the Remote Controller’s ID

Multi Zone

See “Zone 2” for more detail (➔ 61).

Tuner

For FM/AM tuning to work properly, you must specify the

FM/AM step used in your area. Note that when this setting

is changed, all radio presets will be deleted.

■ FM/AM Frequency Step (North American

models)

` 200k/10kHz

Select if 200 k/10 kHz steps are used in your area.

` 50k/9kHz:

Select if 50 k/9 kHz steps are used in your area.

■ AM Frequency Step (Australian models)

` 10kHz

Select if 10 kHz steps are used in your area.

` 9kHz:

Select if 9 kHz steps are used in your area.

SIRIUS Settings (North American models)

See the separate Satellite Radio Guide for more informa-

tion.

■ SAT Radio Mode

If you connect a SIRIUS Satellite Radio antenna to the

AV receiver (sold separately), set this setting to “SIR-

IUS”.

■ Antenna Aiming

■ SIRIUS Parental Lock

These items are for use with SIRIUS Satellite Radio.

It’s not available if “SAT Radio Mode” is set to

“None”.

HDMI

■ Audio TV Out

` Off

HDMI audio is not output.

` On:

HDMI audio is output.

This preference determines whether audio received at the

HDMI IN is output by the HDMI OUT. You may want to

turn this preference on if your TV is connected to the

HDMI OUT and you want to listen to the audio from a

component that’s connected to an HDMI IN, through your

TV’s speakers. Normally, this should be set to “Off”.

Note

•If

“On” is selected and the audio can be output from the TV, the

AV receiver will output no sound through its speakers. In this

case, “TV Sp On” appears on the display.

•When

“TV Control” is set to “On” (➔ 58), this setting is fixed

“Auto”.

• With some TVs and input signals, no sound may be output even

when this setting is set to

“On”.

•When the “Audio TV Out” setting is set to

“On”, or “TV Con-

trol” is set to

“On” (➔ 58) and you’re listening through your

TV’s speakers (➔ 17), if you turn up the AV receiver’s volume

control, the sound will be output by the AV receiver’s front left

Hardware Setup

While holding down Receiver, press and hold

down Setup until the Remote indicator lights

(about 3 seconds) (➔ 43).

Use the number buttons to enter ID 1, 2, or 3.

The Remote indicator flashes twice.