Owner's Manual

46
En
Wireless Front High, Wireless Surround Back,
Wireless Subwoofer
` Yes:
The audio is output from the speakers connected to
the wireless unit.
` No:
The audio is not output from the speakers connected
to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio from the speakers connected to the
wireless unit.
Note
•If theFront High” setting is set to “None” ( page 45),
Wireless Front High” cannot be selected.
•If theSurround Back” setting is set to “None” ( page 45),
Wireless Surround Back” setting cannot be selected.
•If theSubwoofer” setting is set to “No” ( page 45),
Wireless Subwoofer” setting cannot be selected.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
Unit
` feet:
Distances can be set in feet. Range: 0.2ft to 30.0ft in
0.2 foot steps.
` meters:
Distances can be set in meters. Range: 0.06m to
9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
` Specify the distance from each speaker to your
listening position.
Note
These settings are not available in either of the following cases:
a pair of headphones is connected.
–theAudio TV Out” setting is set to “On” ( page 56).
–“HDMI Control (RIHD)” is set to “On” ( page 56) and
you’re listening through your TV speakers.
Speakers that you set to “No” or “None” in the “Speaker
Configuration” cannot be selected ( page 45).
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Left, Front High Left, Center
*1
, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
` –12dB to 0dB to +12dB in 1 dB step.
Subwoofer
*1
` –15dB to 0dB to +12dB in 1 dB step.
Note
These settings cannot be calibrated in either of the following
cases:
a pair of headphones is connected.
–theAudio TV Out” setting is set to “On” ( page 56).
–“HDMI Control (RIHD)” is set to On” ( page 56) and
you’re listening through your TV speakers.
the AV receiver is muted.
Speakers that you set to “No” or “None” in the “Speaker
Configuration” cannot be selected ( page 45).
The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at
volume settings below this, be careful because the test tone will
be much louder.
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved in this menu
( page 40).
Tip
If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 5-band equalizer. The volume
of each speaker can be set ( page 46).
Equalizer
` Manual:
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
speaker setting menu may appear on screen.
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup ( page 31).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup ( page 31).
1
Press w to select “Channel”, and then use
e/r to select a speaker.
2
Use q/w to select a frequency, and then use
the e/r to adjust the level at that frequency.
The volume at each frequency can be adjusted
from +6dB to 0dB
to +6dB in 1 dB steps.
Tip
Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.