DTR-30.6 Basic Manual Advanced Manual found here http://integraworldwide.com/manual/dtr306/adv/en.
Before Start Advanced Manual Advanced Manual is always updated with the latest information and its user friendly interface, which does not matter whether you access from PC or Smartphone, helps you to understand more deeply about the AV Receiver. Advanced Manual is consisted of the following chapters.
Step 1: Connections TV HDMI IN Personal computer HDMI OUT To use the ARC function, connect to the ARC compatible HDMI jack of the TV and make an appropriate setting on the unit. See "2nd Step : Source Connection" of "Step 2: Setting Up". HDMI cable HDMI OUT HDMI OUT HDMI OUT Game console Set-top box/Digital video recorder, etc. 1 Connecting the TV and players Important: The power cord must be connected only after all other connections are completed.
Step 1: Connections Home on the remote controller, select "Setup" - "1. Input/ Output Assign" - "Monitor Out" and set the default value of "MAIN" to "SUB" or "MAIN+SUB". The unit supports the HDMI Through function that allows transmission from players to the TV even if the unit is in standby. You have to modify the settings to enable the input selection link with CEC compliant device, connection with ARC compatible TV, and HDMI Through function. See "2nd Step : Source Connection" of "Step 2: Setting Up".
Step 1: Connections 2 2 Front R Connecting speakers 1 Front L Important: The power cord must be connected only after all other connections are completed. 12 3 9F 3 Center 6 45 78 12 3 45 6 78 9F Front speakers Center speaker Surround speakers Subwoofer Surround back speakers Height speakers • 5.1 ch: 1 2 3 4 5 6 • 7.1 ch: 1 2 3 4 5 6 + 7 8 or 123456+9F • Up to two subwoofers can be connected.
Step 1: Connections 1/2"-5/8"(12-15 mm) Cut and remove the plastic coating from the end of the speaker cable, twist the core and connect it to the terminal. Make correct connection between the unit's jacks and speaker's jacks (+ to + and - to -) for each channel. If connection is wrong, a bass sound may become poor due to reverse phase. Attaching the supplied colored speaker cable labels to the + side on the both ends of each channel's cable will help correct connection.
Step 2: Setting Up Important: When the unit is turned on for the first time, the setup wizard of the section 2 will automatically be launched. If you use the setup wizard to make the initial setup, connect a TV to the HDMI OUT MAIN jack of the unit via HDMI connection. 1 Turning the power on Connect the power cord to the outlet. Press zOn/Standby on the main unit or zReceiver on the remote controller to turn the unit on or to standby mode.
Step 2: Setting Up 2. After placing the microphone at the measurement position, select "Do it Now" in the start screen and press Enter. 3. Connect the microphone to the Setup Mic jack of the unit. Setup Mic jack Speaker setup microphone 4. Follow the guidance displayed on the TV screen. Powered Zone 2 2nd Step : Source Connection Normal You can check whether or not each input source is connected correctly.
Step 2: Setting Up 2. Select and set the authentication method. 4th Step : Network Connection Wi-Fi Setup Initial Setup Select the authentication method. Network Connection Do you want to connect network connection? It gives you network services that our AV receiver support. If you wish to skip this step. select “No. Skip”. Enter Password Push Button PIN code Yes No. Skip HOME Exit You can check the network connection and make the WiFi setting.
Step 3: Playing Back 1 Playing the player and TV Remote controller parts name 1 1 z Receiver button: Turns the unit on or into standby mode. 2 2 RCV button: Switches the remote controller to the mode for operating this unit. 3 8 3 Remote Mode/Input Selector button: Switches the input to be played. 4 Cursor buttons and Enter button: Moves the cursor 9 To control the unit: You can control any other device than this unit if you register the specified remote control code to 3 Remote Mode.
Listening modes Select the desired mode by switching and listening actual sound in different modes. The selectable listening modes depend on the format of the input signals. Movie/TV: You can select a listening mode suitable for movies and TV programs. Music: You can select a listening mode suitable for music. Game: You can select a listening mode suitable for games. Stereo: You can select a listening mode for stereo and all channel stereo sources.
3 Connecting and playing the Bluetoothenabled device You can wirelessly enjoy music files stored in a smartphone or other Bluetooth-enabled device. The coverage area is 48 feet (15 meters). • The Bluetooth-enabled device needs to support the A2DP profile. • Note that connection is not always guaranteed with all Bluetooth-enabled devices. Pairing Pairing is necessary when using the Bluetooth-enabled device for the first time.
Step 3: Playing Back USB: Select "USB" in the TV screen and connect a USB storage device to the USB port on the front panel. On the TV screen, select the desired folder or music file with the cursors of the remote controller and press Enter to confirm and start playback. • "USB" becomes selectable after the USB function starts up even if it cannot be selected first. It may take about a minute to start up.
Step 3: Playing Back 6 Using the multi-zone function The function allows you to connect the unit with an audio equipment placed in a separate room so that you can enjoy audio of the connected equipment even if you are staying in a different room. It is possible to perform playback in the main room and a separate room at the same time, for example by playing the Blu-ray Disc player in the main room where the unit is placed while playing Internet radio in a separate room.
Step 3: Playing Back Performing Multi-zone Playback 1. Press Zone2 on the remote controller, point the remote controller at the remote controller sensor and press zReceiver. "Z2" stays lit on the main unit display and the multi-zone function is enabled. 2. Press Zone2 again on the remote controller and press Input Selector of the input to be played in a separate room. To play the same source in the main room and separate room, hold down Zone2 for approximately 3 seconds.
1 23 4 5 6 7 8 9 F G H I J K (Australian model) L M N O P Q R S T Front Panel 1 zOn/Standby button: Turns the unit on or into standby mode. 2 Bluetooth indicator: Flashes while pairing with a Bluetooth-enabled device is in progress and stays lit when pairing is completed. 3 Wi-Fi indicator: Stays lit while the unit is connected to the wireless LAN router. 4 TONE and Tone Level buttons: Adjusts the high tone and low tone.
1 2 G 3 H 4 5 I 6 J 7 8 K 9 L F M Rear Panel 1 RI REMOTE CONTROL jack: An Onkyo product with RI jack can be connected and synchronized with this unit. 2 FM ANTENNA jack (75 Ω) and AM ANTENNA terminal: The supplied antennas are connected. 3 COMPONENT VIDEO IN/OUT jacks: Component video input/output jacks 4 ETHERNET port: Used for LAN connection 5 RS232 port: Connected to the home control system. () 6 IR IN A/B/OUT jack: Connected to the multiroom remote control kit.
1 2 3 4 9 5 6 7 8 Display 1 Stays lit or flashes in the following conditions. "Z2": Zone 2 output is on. "HDMI": HDMI signals are input and the HDMI input selector is selected. "ARC" (Audio Return Channel): Audio signals are input from the ARC compatible TV and the TV/CD input selector is selected. "3D": Input signals are 3D. "USB": "USB" input is selected and USB storage device is connected. • It will flash if the USB storage device is not correctly connected.
Troubleshooting Before starting the procedure Problems may be solved by simply turning the power on/off or disconnecting/connecting the power cord, which is easier than working on the connection, setting and operating procedure. Try the simple measures on both the unit and the connected device. If the problem is that the video or audio is not output or the HDMI linked operation does not work, disconnecting/connecting the HDMI cable may solve it.
Specifications Amplifier Section Network Section Rated Output Power All channels: 95 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) 115 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.
License and Trademark Information Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS-HD Master Audio is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
DISCLAIMER For U.S. models Through this device you are able to link to other services or websites which are not under the control of any company which has designed, manufactured or distributed/have distributed this device, and its affiliates (collectively, “Company”). We have no control over the nature, content and availability of those services. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
Integra Division of 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu Integra Division of 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.integra.com.
