AV Receiver DTR-4.
Thank you for purchasing an Integra AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth.
* 4 1 Surround Left Surround Left Surround Right Surround Right Surround Left Surround Left Surround Right Surround Right Surround Back Right Surround Back Right Zone 2 Right Zone 2 Right Surround Back Right Surround Back Right Zone 2 Right Zone 2 Right Center Surround Back Left Surround Back Left Zone 2 Left Zone 2 Left Surround Back Left Surround Back Left Zone 2 Left Zone 2 Left Center Center Front Right Front Right SP-B / Zone 2 Right SP-B / Zone 2 Right Front Right Front Right SP-B / Zone 2 R
Contents Important Safety Instructions .......................... 2 Supplied Accessories ...................................... 4 Features ............................................................ 6 Multiroom Capability ........................................ 7 Getting to Know the AV Receiver ................... 8 Front Panel ..............................................................8 Display ....................................................................9 Rear Panel ...........................
Features Amplifier *1 • 5-channel amplifier • WRAT-Wide Range Amplifier Technology (5Hz–100kHz bandwidth) • Optimum Gain Volume Circuitry Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.
Multiroom Capability You can use two speaker systems with this AV receiver—a surround-sound speaker system (up to 5.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it. And, you can select a different audio source for each room. Main Room: In your main listening room, you can enjoy up to 5.1-channel playback (see page 14). You can enjoy the various listening modes such as Dolby and DTS (pages 50–55).
Getting to Know the AV Receiver Front Panel 1 2 3 P Q 4 R 5 6 7 89 J K L M S N O T The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item. A On/Standby button (34) Sets the AV receiver to On or Standby. B Standby indicator (34) Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller.
Getting to Know the AV Receiver—Continued P Zone 2, Level [ ]/[ ], and Off buttons (68) The Zone 2 button is used when setting Zone 2. The Level Up and Down [ ]/[ ] buttons are used when adjusting the volume level of Zone 2. The Off button is used to turn off Zone 2. R Input selector buttons (43) Select the following input sources: DVD, VCR/DVR, CBL/SAT, Game/TV, Tape, Tuner, CD. The [Multi CH] button selects the multichannel DVD input.
Getting to Know the AV Receiver—Continued Rear Panel 1 2 3 4 5 6 78 9 J K L AM ANTENNA FM 75 PRE OUT SUB WOOFER M N O P QR ST U A DIGITAL IN COAXIAL 1 and 2 These coaxial digital audio inputs are for connecting components with a coaxial digital audio output, such as a CD player or DVD player. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 40.
Getting to Know the AV Receiver—Continued M DIGITAL OPTICAL IN 1, 2, and OUT These optical digital audio inputs are for connecting components with an optical digital audio output, such as a CD player or DVD player. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 40. The optical digital audio output is for connecting a digital recorder with an optical digital input, such as a CD recorder.
Remote Controller Controlling the AV Receiver D Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons To control the AV receiver, press the [Receiver] Remote Mode button to select Receiver mode. You can also use the remote controller to control your DVD player, CD player, and other components. See page 71 for more details. Used to select and adjust settings. E Setup button Used to change settings. F Listening Mode buttons (50) Used to select the listening modes. G Dimmer button (44) Adjusts the display brightness.
Remote Controller—Continued Installing the Batteries 1 To open the battery compartment, press the small lever and remove the cover. Using the Remote Controller When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below. Remote control sensor Standby indicator AV receiver 30˚ 2 3 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. Replace the cover and push it shut.
Connecting Your Speakers Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS. With analog or digital TV, you can enjoy Dolby Pro Logic II, DTS Neo:6, or Onkyo’s original DSP listening modes. Front left and right speakers These output the main sound.
Connecting Your Speakers—Continued Speaker Configuration Connecting a Powered Subwoofer For 5.1-channel surround-sound playback, you need five speakers and a powered subwoofer. Using a suitable cable, connect the AV receiver’s PRE OUT: SUBWOOFER to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the PRE OUT: SUBWOOFER to the amp’s input. The following table shows which channels you should use based on the number of speakers you have.
Connecting Your Speakers—Continued Speaker Connection Precautions Read the following before connecting your speakers: • You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated. • Disconnect the power cord from the wall outlet before making any connections. • Read the instructions supplied with your speakers.
Connecting Antennas This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Connecting the AM Loop Antenna The supplied indoor AM loop antenna is for indoor use only. 1 Assemble the AM loop antenna, inserting the tabs into the base, as shown.
Connecting Antennas—Continued Connecting an Outdoor FM Antenna Connecting an Outdoor AM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
Connecting Your Components AV Connection Color Coding About AV Connections RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs. • Before making any AV connections, read the manuals supplied with your other AV components.
Connecting Your Components—Continued Connecting Audio and Video Signals to the AV Receiver By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD player, etc.
Connecting Your Components—Continued Connecting a TV or Projector Step 1: Video Connection Choose a video connection that matches your TV ( A , B , or C ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from your TV or listen in Zone 2. • To enjoy Dolby Digital and DTS, use connection b or c .
Connecting Your Components—Continued Connecting a DVD player Step 1: Video Connection Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from a DVD or listen in Zone 2.
Connecting Your Components—Continued Hooking Up the Multichannel Input If your DVD player supports multichannel audio formats such as DVD-Audio and SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT L/R, CENTER, SURR L/R, and SUBWOOFER jacks to the 5.1-channel analog audio output on your DVD player.
Connecting Your Components—Continued Connecting a VCR or DVR for Playback With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches your VCR or DVR ( A , B , or C ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection.
Connecting Your Components—Continued Connecting a VCR or DVR for Recording Step 1: Video Connection Choose a video connection that matches your VCR or DVR ( A or B ), and then make the connection. The video source to be recorded must be connected to the AV receiver via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your VCR or DVR ( a or b ), and then make the connection.
Connecting Your Components—Continued Connecting a Satellite, Cable, or Terrestrial Set-top box or Other Video Source With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches the video source ( A , B , or C ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection.
Connecting Your Components—Continued Connecting Components with HDMI About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Connecting Your Components—Continued Making HDMI Connections If you have an HDMI-compatible player, you can connect it to the AV receiver with an HDMI cable. Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV, projector, and so on. Step 2: Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 39). ■ Audio Signals Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV receiver.
Connecting Your Components—Continued Connecting a Camcorder, Game Console, or Other Device Step 1: Video Connection A or B Connect your camcorder’s video output jack to the AV receiver’s GAME/TV IN S or V jack. Connect the AV receiver’s MONITOR OUT to your TV’s video input with the same type of connection. C Step 2: Audio Connection a or b Connect your camcorder’s audio output jack to the AV receiver’s DIGITAL IN OPTICAL 1 or GAME/TV IN L/R jacks.
Connecting Your Components—Continued Connecting a CD Player or Turntable ■ CD Player or Turntable (MM) with Built-in Phono Preamp Step 1: Choose a connection that matches your CD player ( a , b , or c ). Use connection a for a turntable with a built-in phono preamp.
Connecting Your Components—Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches your recorder ( a , b , c , or d ), and then make the connection. b COAXIAL 2 (CBL/SAT) c OPTICAL AM a IN L 2 (CD) ANTENNA R FM 75 TAPE d PRE OUT L DIGITAL OUT a SUB WOOFER R TAPE Connect one or the other These connections must be assigned (see page 40) L COAXIAL OUT OPTICAL OUT OPTICAL IN R AUDIO IN L R AUDIO OUT Cassette, CDR, MD, etc.
Connecting Your Components—Continued Connecting an RI Dock Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock’s instruction manual. ■ If Your iPod Doesn’t Support Video: Connect your RI Dock’s audio output jacks to the AV receiver’s TAPE IN L/R jacks.
Connecting Your Components—Continued Connecting Integra/Onkyo Components Step 1: Make sure that each Integra/Onkyo component is connected to the AV receiver with an analog audio cable (RCA). Step 2: Make the necessary connections (see illustration below). Step 3: If you’re using an MD, CDR, or RI DOCK component, change the Input Display (see page 41).
Turning On the AV Receiver On/Standby Standby indicator On/Standby Receiver Connecting the Power Cord • Before connecting the power cord, connect all your speakers and AV components. • Plug the end of the power cord into a suitable wall outlet. • Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
First Time Setup This section explains the settings that you need to make before using the AV receiver for the very first time. Speaker Settings 3 Use the Up and Down [ ]/[ ] buttons to select “Sp Config,” and then press the [Enter] button. 4 While the “Subwoofer” setting is selected, use the Left and Right [ ]/[ ] buttons to select Yes or No. Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected.
First Time Setup—Continued 7 Use the Down [ ] button to select “Surr,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency. If no surround left and right speakers are connected, select None. Note: • Cannot select Full Band if Front (step 5) is set to anything other than Full Band. Double Bass With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and center to the subwoofer.
First Time Setup—Continued 3 Use the Up and Down [ ]/[ ] buttons to select “2. Speaker Setup,” and then press the [Enter] button. • This procedure can also be performed on the AV receiver by using its [Setup], [Enter], and arrow buttons. Speaker Levels You can set the volume level of each speaker so that all speakers can be heard equally at the listening position. 4 5 1 Press the [Receiver] Remote Mode button, followed by the [Setup] button. 2 Use the Up and Down [ ]/[ ] buttons to select “2.
First Time Setup—Continued 7 Press the [Setup] button. Setup closes. Don’t forget to turn down the volume if you turned it up while setting the levels. 5 Press the Down [ ] button, and then use the Left and Right [ ]/[ ] buttons to select a speaker. 6 Use the Up and Down [ ]/[ ] buttons to select a frequency. Use the Left and Right [ ]/[ ] buttons to adjust the level at that frequency. Notes: • The speaker levels cannot be adjusted while a pair of headphones is connected or the AV receiver is muted.
First Time Setup—Continued HDMI Input Setup 4 Use the Up and Down [ ]/[ ] buttons to select an input selector, and use the Left and Right [ ]/[ ] buttons to select: HDMI1: Select if the video component is connected to HDMI IN 1. HDMI2: Select if the video component is connected to HDMI IN 2. HDMI3: Select if the video component is connected to HDMI IN 3. - - - - -: Select if you’re not using the HDMI IN1–IN3. 5 Press the [Setup] button. Setup closes.
First Time Setup—Continued Component Video Input Setup 4 Use the Up and Down [ ]/[ ] buttons to select an input selector, and use the Left and Right [ ]/[ ] buttons to select: IN1: Select if the video component is connected to COMPONENT VIDEO IN 1. IN2: Select if the video component is connected to COMPONENT VIDEO IN 2. - - - - -: Select if you’re not using the COMPONENT VIDEO IN1 or IN2. 5 Press the [Setup] button. Setup closes.
First Time Setup—Continued 2 Use the Up and Down [ ]/[ ] buttons to select “1.Input Assign,” and then press [Enter]. Changing the Input Display If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT jacks, or connect an RI Dock to the GAME/TV jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 1, 2 Use the Up and Down [ ]/[ ] buttons to select “1-3.Digital,” and then press [Enter].
First Time Setup—Continued Automatic Audio Input Selection Setup 2, 3 1 When an input source is selected, the AV receiver checks the relevant audio inputs for the presence of an audio signal and automatically selects an input. With this setting, you can specify which audio inputs the AV receiver will check for signals. 42 1 Press the input selector button for the input selector whose setting you want to change. The setting for the TUNER input selector cannot be changed and is fixed at “Analog.
Playing Your AV Components Basic AV Receiver Operation 1 3 3 1 1 Use the AV receiver’s input selector buttons to select an input source. AV receiver Remote controller To select an input source with the remote controller, press its Input Selector buttons. To listen to a DVD player connected to the multichannel DVD input (page 23), press the AV receiver’s [Multi CH] button. The MULTI CH indicator will appear on the display.
Common Functions This section explains functions that can be used with any input source. Muting the AV Receiver You can temporarily mute the output of the AV receiver. Display Press [Receiver] first Muting Press the [Receiver] Remote Mode button, and then press the remote controller’s [Muting] button. The output is muted and the MUTING indicator flashes on the display. To unmute the AV receiver, press the remote controller’s [Muting] button again, or adjust the volume.
Common Functions—Continued 7Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s Phones jack. Displaying Source Information You can display various information about the current input source as follows. Press the [Receiver] Remote Mode button, and then press the [Display] button repeatedly to cycle through the available information. Notes: • Always turn down the volume before connecting your headphones.
Common Functions—Continued Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Display Dolby Digital DTS PCM PCM Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. • If the beginnings of tracks from a PCM source are cut off, try the PCM setting.
Listening to the Radio ■ Manual Tuning Mode Listening to AM/FM Stations Tuning Mode Tuning Tuner With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection. Use the [Tuner] input selector button to select AM or FM. In this example, FM has been selected. Band 1 Press the [Tuning Mode] button so that the AUTO indicator disappears from the display. 2 Press and hold the Tuning Up or Down [ ]/[ ] button.
Listening to the Radio—Continued ■ Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. Displaying AM/FM Radio Information Display Tuner Press the [Display] button to display the available information. Band Frequency Number buttons D.TUN Listening mode 1 Press the [Tuner] button repeatedly to select AM or FM, followed by the [D.TUN] button. (Actual display depends on country.
Listening to the Radio—Continued Presetting AM/FM Stations 2, 4 Selecting Presets Preset 3 You can store a combination of up to 40 of your favorite AM and FM radio stations. 1 Tune into the AM or FM station you want to store as a preset. 2 Press the [Memory] button. The preset number flashes. 3 While the preset number is flashing (about 8 seconds), use the Preset [ ]/[ ] buttons to select a preset from 1 through 40. 4 Press the [Memory] button again to store the station.
Using the Listening Modes Selecting the Listening Modes Selecting with the Remote Controller For a description of each listening mode, see “About the Listening Modes” on page 54. • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). Movie/TV Music Stereo Game • The listening modes you can select depends on the format of the input signal.
Using the Listening Modes—Continued Listening Modes Available for Each Source Format Analog and PCM Sources PCM Source format Media Button Listening Mode Mono Multichannel 32–96 176.
Using the Listening Modes—Continued Dolby Digital and Dolby Digital Plus Sources Dolby Digital Dolby Digital Plus Multichannel 2ch Mono/Multiplex Multichannel 2ch Mono/Multiplex Source format Media Button DVD, DTV, etc.
Using the Listening Modes—Continued DTS Sources DTS, DTS 96/24 Source format Multichannel Media Button DTS, DTS 96/24 ✔ ✔ Dolby PLII Movie Neo:6 Cinema [Movie/TV] MonoMovie*1 *2 TV Logic*1 *2 AllChStereo FullMono T-D*2 Direct Stereo DTS, DTS 96/24 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Dolby PLII Music [Music] Neo:6 Music Orchestra*1 *2 Unplugged*1 *2 Studio-Mix*1 *2 AllChStereo FullMono DTS, DTS 96/24 ✔ ✔ ✔ ✔ ✔ ✔ Dolby PLII Game [Game] AllChStereo FullMono T-D*2 [Stereo] AllChStereo Stereo Mono DVD, CD, etc.
Using the Listening Modes—Continued About the Listening Modes Dolby Digital Plus The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. The illustration shows which speakers are active in each listening mode with 5.1 channel speaker system.
Using the Listening Modes—Continued Onkyo Original DSP Modes Mono Movie This mode is suitable for old movies and other mono sources. The center speaker outputs the sound as it is, while reverb is applied to the sound output by the other speakers, giving presence to even mono material. Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image and simulates the natural reverberation of a large hall.
Recording This section explains how to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded. • Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded. • DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.
Adjusting the Listening Modes Using the Audio Adjust Settings With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. 1 Press the [Receiver] Remote Mode button, followed by the [Setup] button. Note: • This procedure can also be performed on the AV receiver by using its [Setup], [Enter], and arrow buttons. The Audio Adjust settings are explained below. Multiplex/Mono Settings Mux (Multiplex) 2 Use the Up and Down [ ]/[ ] buttons to select “3.
Adjusting the Listening Modes—Continued ■ Center Width With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic II Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output by only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center).
Adjusting the Listening Modes—Continued Late Night Function Speaker Levels ■ Late Night With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone. For Dolby Digital and Dolby Digital Plus sources, the options are: Off: Late Night function off (default). Low: Small reduction in dynamic range.
Adjusting the Listening Modes—Continued Listening Mode Presets 4 On the Listening Mode Preset menu, you can specify a default listening mode for each of the audio formats supported by each input selector. The AV receiver will then select the listening mode automatically depending on the format of the input signal. You can still select the other listening modes, although the default listening mode will be used the next time you turn on the AV receiver.
Advanced Setup Source Setup 6 This section explains items on the Source Setup menu. Items can be set individually for each input selector. 1 Press the input selector buttons to select an input source, and then press the [Receiver] Remote Mode button. When you’ve finished, press the [Setup] button. Setup closes. Note: • This procedure can also be performed on the AV receiver by using its [Setup], [Enter], and arrow buttons.
Advanced Setup—Continued Miscellaneous Setup This section explains items on the Miscellaneous menu. 1 Press the [Receiver] Remote Mode button, followed by the [Setup] button. Volume Setup ■ MaxVolume With this setting, you can limit the maximum volume. The Maximum Volume range is Off, 79 to 30. ■ PowOn Vol This setting determines what the volume will be each time the AV receiver is turned on. The range is Last, Min, 1 to 79, Max.
Advanced Setup—Continued Hardware Setup 4 Use the Up and Down [ ]/[ ] buttons to select an item, and use the Left and Right [ ]/[ ] buttons to change it. The items are explained below. 5 When you’ve finished, press the [Setup] button. Setup closes. This section explains items on the Hardware menu. Remote indicator Receiver Note: • This procedure can also be performed on the AV receiver by using its [Setup], [Enter], and arrow buttons.
Advanced Setup—Continued AnalogMulti ■ SW In Sens Some DVD players output the LFE channel from their analog subwoofer output at 15 dB higher than normal. With this setting, you can change the AV receiver’s subwoofer sensitivity to match your DVD player. Note that this setting only affects signals connected to the AV receiver’s MULTI CH SUBWOOFER jack. You can select 0 dB, 5 dB, 10 dB, or 15 dB. If you find that your subwoofer is too loud, try the 10 dB or 15 dB setting.
Advanced Setup—Continued PowCtrl To link the power functions of RIHD-compatible components connected via HDMI, select Enable. Disable: Power Control disabled. Enable: Power Control enabled. Notes: • The Power Control setting can be set only when the above Control setting is set to Enable. • HDMI power control only works with RIHD-compatible components that support it and may not work properly with some components due to their settings or compatibility.
Zone 2 In addition to your main listening room, you can also enjoy playback in the other room, or as we call Zone 2. And, you can select a different source for each room. Connecting Zone 2 Zone 2 Out Settings Connecting Your Zone 2 Speakers to an Amp in Zone 2 This setup allows 5.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2, with a different source in each room.
Zone 2—Continued 5 Press the [Setup] button. Setup closes. Note: • This procedure can also be performed on the AV receiver by using its [Setup], [Enter], and arrow buttons. Using Zone 2 This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2. 2 To turn off Zone 2, press the Zone 2 [Off] button. Notes: • Only analog input sources are output by Zone 2. Digital input sources are not output.
Zone 2—Continued Zone 2 Tone 2 Press the AV receiver’s [Tone] button repeatedly to select Balance. 3 Use the Tone Plus [+] and Minus [–] buttons to adjust the balance. You can adjust the balance from 0 in the center to +10 to the right or +10 to the left in 2 steps. +, – Zone 2 Level Zone2 Muting Zone 2 Muting VOL On the remote controller, press the [Zone 2] Remote Mode button, and then press the [Muting] button.
Zone 2—Continued Using the 12V Triggers 3 Use the Up and Down [ ]/[ ] buttons to select “12V Trg A, B, or C,” and then press [Enter]. 4 Use the Up and Down [ ]/[ ] buttons to select “Delay,” and use the Left and Right [ ]/[ ] buttons to select: 0 sec, 1 sec, 2 sec, or 3 sec. When 0 sec is selected, the trigger signal is output as soon as the input source is changed. 5 Use the Up and Down [ ]/[ ] buttons to select an input source, and use the Left and Right [ ]/[ ] buttons to select an option.
Zone 2—Continued Using the Remote Controller in Zone 2 and Multiroom Control Kits To control the AV receiver with the remote controller while you’re in Zone 2, you’ll need a commercially available multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s installed inside a cabinet.
Controlling Other Components You can control your DVD player, CD player, and other components with the AV receiver’s remote controller. To control another component, you must first enter that component’s remote control code to a Remote Mode button. This section explains how to enter remote control codes and how to control your other components. 1 Look up the component’s remote control code in the separate Remote Control Codes list. The codes are organized by category.
Controlling Other Components—Continued Remote Control Codes for Integra/Onkyo Components Connected via Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 Make sure the Integra/Onkyo component is connected with an cable and an analog audio cable (RCA). See page 33 for details.
Controlling Other Components—Continued Controlling a DVD Player, or DVD Recorder By pressing the Remote Mode button that’s been programmed with the remote control code for your DVD player (HD DVD, Blu-ray, or TV/DVD combination), you can control your player with the following buttons. A On/Standby button The [DVD] Remote Mode button is preprogrammed with the remote control code for controlling an Onkyo DVD player.
Controlling Other Components—Continued T Play Mode button Selects play modes on components with selectable play modes. U CLR button Cancels functions and clears entered numbers. Note: • If you enter the remote control code for a HD DVD or Blu-ray player that has A, B, C, and D or colored buttons, the [SEARCH], [REPEAT], [RANDOM], and [PLAY MODE] buttons will work as colored or A, B, C, D buttons. In this case, these buttons cannot be used to set repeat playback, random playback, or select play modes.
Controlling Other Components—Continued Controlling a Satellite Receiver or Cable Receiver By pressing the Remote Mode button that’s been programmed with the remote control code for your satellite receiver, cable receiver, or DVD recorder (DBS/DVR combination or cable/DVR combination), you can control your player with the following buttons. For details on entering a remote control code for a different component, see page 71. A On/Standby button Set the component to On or Standby.
Controlling Other Components—Continued Controlling a CD Player, CD Recorder, or MD Player By pressing the Remote Mode button that’s been programmed with the remote control code for your CD player, CD recorder, or MD player, you can control your player with the following buttons. A On/Standby button The [CD] Remote Mode button is preprogrammed with the remote control code for controlling an Integra/Onkyo CD player.
Controlling Other Components—Continued Controlling an RI Dock By pressing the Remote Mode button that’s been programmed with the remote control code for your RI Dock, you can control your iPod in the RI Dock with the following buttons. For details on entering a remote control code, see page 71. When Using an RI Dock: • Connect the RI Dock to the TAPE IN or GAME/TV IN L/R jacks. • Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK. • Set the AV receiver’s Input Display to DOCK (see page 41).
Controlling Other Components—Continued P Fast Forward [ Works as a Resume button when used with a DS-A2 RI Dock. ] button Press and hold to fast forward. S Random button* Q Stop [ ] button Used with the shuffle function. Stops playback and displays a menu. R Play Mode button Selects play modes on components with selectable play modes. *Buttons marked with an asterisk (*) are not supported by 3rd generation iPod models.
Controlling Other Components—Continued Controlling a TV By pressing the [TV] Remote Mode button that’s been programmed with the remote control code for your TV (TV/DVD combination or TV/VCR combination), you can control your TV with the following buttons. A On/standby, TV [ For details on entering a remote control code for a different component, see page 71. C TV [Input] button The [TV] Remote Mode button is preprogrammed with the remote control code for controlling a TV that supports the RIHD*.
Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer. To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [On/Standby] button. “Clear” will appear on the display and the AV receiver will enter Standby mode.
Troubleshooting—Continued There’s no sound with a certain signal format • Check the digital audio output setting on the source component. On some game consoles, such as those that can play DVDs, the default setting is off. • With some DVD-Video discs, you need to select an audio format from a menu or with the Audio button on your DVD player’s remote controller. The volume cannot be set to 79 • Check to see if a maximum volume has been set (page 62).
Troubleshooting—Continued Can’t control other components • Make sure you’ve selected the correct remote controller mode. • If you’ve connected an -capable Onkyo MD recorder, CD recorder, or RI Dock to the TAPE IN/OUT jacks, or an RI Dock to the GAME/TV IN jacks, for the remote controller to work properly, you must set the Input Display to MD, CDR, or DOCK, respectively (see page 41). • The entered remote control code may not be correct. If more than one code is listed, try each one.
Specifications Amplifier Section General Rated Output Power 90 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20Hz to 20kHz, with a maximum total harmonic distortion of 0.08% (FTC) 105 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20Hz to 20kHz, with a maximum total harmonic distortion of 0.7% (FTC) 110 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1kHz, with a maximum total harmonic distortion of 0.
Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 En I0804-1 SN 29344685 (C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
