Owner's Manual

ManualsBrandsIntegra ManualsReceiversIntegra DTR-40.2

Speaker Distance

Here you can specify the distance from each speaker to the

listening position so that the sound from each speaker

arrives at the listener’s ears as the sound designer

intended.

■ Unit

 feet:

Distances can be set in feet. Range: “0.2ft” to

“30.0ft” in 0.2 foot steps.

 meters:

Distances can be set in meters. Range: “0.06m” to

“9.00m” in 0.06 meter steps.

(The default setting varies from country to country.)

■ Left, Front Wide Left, Front High Left, Center,

Front High Right, Front Wide Right, Right, Surr

Right, Surr Back Right, Surr Back Left, Surr

Left, Subwoofer

 Specify the distance from the each speaker to your lis-

tening position.

Note

• Speakers that you set to “No” or “None” in the “Speaker Con-

figuration” cannot be selected (➔ 51).

Level Calibration

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

■ Left, Front Wide Left, Front High Left, Center

Front High Right, Front Wide Right, Right, Surr

Right, Surr Back Right, Surr Back Left, Surr Left

 –12.0dB to 0.0dB

to +12.0dB in 0.5 dB step.

■ Subwoofer

 –15.0dB to 0.0dB to +12.0dB in 0.5 dB step.

Note

• Speakers that you set to “No” or “None” in the “Speaker Con-

figuration” cannot be selected (➔ 51).

• The speakers cannot be calibrated while the AV receiver is

muted.

• The test tone is output at the standard level for THX, which is

0 dB (absolute volume setting 82). If you normally listen at vol-

ume settings below this, be careful because the test tone will be

much louder.

For the center speaker and subwoofer, the level settings made

by using the Home menu are saved (➔ 26).

Tip

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

Equalizer Settings

With the Equalizer settings, you can adjust the tone of

speakers individually with a 15-band equalizer. The vol-

ume of each speaker can be set (➔ 52).

■ Equalizer

 Manual:

You can adjust the equalizer for each speaker manu-

ally. If you selected “Manual”, continue with this

procedure.

 Audyssey:

This is selected automatically by Audyssey MultEQ

Room Correction and Speaker Setup function. The

Audyssey indicator will light (➔ 9) and

“Dynamic EQ” (➔ 55) and “Dynamic Volume”

(➔ 56) become available.

 Off:

Tone off, response flat.

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 28).

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 28).

This setting is set automatically by Audyssey MultEQ

Room Correction and Speaker Setup function (➔ 28).

Press w to select “Channel”, and then use e/

r to select a speaker.

Use q/w to select a frequency, and then use

the e/r to adjust the level at that frequency.

The volume at each frequency can be adjusted

from –6dB to 0dB

to +6dB in 1 dB steps.

Note

• You can select: “25Hz”, “40Hz”, “63Hz”,

“100Hz”, “160Hz”, “250Hz”, “400Hz”, “630Hz”,

“1000Hz”, “1600Hz”, “2500Hz”, “4000Hz”,

“6300Hz”, “10000Hz”, or “16000Hz”. And for the

subwoofer, “25Hz”, “40Hz”, “63Hz”, “100Hz”, or

“160Hz”.

• While the Direct listening mode is selected, the

equalizer settings have no effect.

Tip

• Low frequencies (e.g., 63Hz) affect bass sounds;

high frequencies (e.g., 16000Hz) affect treble

sounds.

Use q to select “Channel”, and then use e/r

to select another speaker.

Repeat steps 1 and 2 for each speaker.

You cannot select speakers that you set to “No”

or “None” in the “Speaker Configuration”

(➔ 51).