Owner's Manual

18
14
G
23 6 7 8 95 F
I
J
H
LMK
Rear Panel
1 RI REMOTE CONTROL jack: An Onkyo product with RI
jack can be connected and synchronized with this unit.
2 : The supplied
antennas are connected.
3 COMPONENT VIDEO IN/OUT jacks: Component video
input/output jacks.
4 ETHERNET port: Used for LAN connection.
5 RS232 port: Connected to the home control system. (¼)
6 IR IN A/B, IR OUT jack: Connected to the multiroom
remote control kit. (¼)
7 12V TRIGGER OUT A/B/C jacks: Allows you to connect
a device with 12V trigger input jack to enable link
operation between the device and the unit. (¼)
¼ Special devices or cable connections are necessary to use the
control functions 5 to 7. Contact the specialized stores for more
information.
8 HDMI IN/OUT jacks: Digital video signals and audio
signals are transmitted between the unit and the
connected devices.
9 HDBaseT™ IN/OUT ports: HDMI input signals are
output via the Ethernet cable. As they are covered with
a seal when shipped, remove it when you use the ports.
Do not use the ports to connect the Ethernet port of
network device.
F AC INLET: The power cord is connected.
G DIGITAL IN COAXIAL/OPTICAL jacks: Digital audio
signals are input.
H GND terminal: The ground wire of the turntable is
connected.
I COMPOSITE VIDEO/AUDIO IN jacks: Analog video
signals and audio signals are input.
J MONITOR OUT V jack: Video signals are output to the
connected monitor or TV via a composite video cable.
K PRE OUT jacks: A power amplifier or subwoofer with
built-in amplifier is connected.
L PRE/LINE OUT ZONE2/ZONE3 jacks: Audio output
jacks connected to the integrated amplifier for multi-zone
playback in a separate room.
M SPEAKERS terminals: Speakers are connected. To
use the Multi-zone function, connect the speakers in the
separate room to the ZONE2 speaker terminals.
14 623 75
98
Display
1 Stays lit in the following conditions.
"Z2" "Z3" (¼1): Zone 2 or Zone 3 output is on. /
"HDMI": HDMI signals are input and HDMI input selector
is selected. / "ARC": Audio signals are input from ARC
compatible TV and TV/CD input selector is selected. /
"3D": Input signals are 3D. / "USB" (¼2): "USB" input is
selected and USB storage device is connected. /
"NET" (¼2): "NET" input is selected and the unit is
connected to the network. / "DIGITAL": Digital signals
are input and the digital input selector is selected. /
Cursor indicators: NET or USB is controlled.
¼1 Both "Z2" and "Z3" light when the WHOLE HOUSE MODE function
is on.
¼2 "USB" and "NET" will flash if the connection is not correct.
2 Stays lit while headphones are connected.
3 Stays lit while NET or USB is controlled.
4 Stays lit according to the type of input digital signals and
the listening mode.
5 Stays lit while Music Optimizer is enabled.
6 Stays lit in the following conditions. "AUTO": Tuning
mode is auto. / "fTUNEDe": Receiving AM/FM radio.
fe flashes while tuning is automatically performed. /
"FM STEREO": Receiving FM stereo. /
"RDS" (Australian models): Receiving RDS broadcasting.
7 "MUTING": Flashes when muting is on.
8 Stays lit in the following conditions. "SLEEP": Sleep
timer has been set. / "ASb": Auto Standby is on. /
"ch": Channel is being set. / "Hz": Crossover frequencies
are being set. / "m/ft": Speaker distances are being set. /
"dB": Speaker volume is being set.
9 Displays various information of the input signals.
Pressing Display displays the type of input digital signals
and the listening mode.