Owner's Manual

Advanced Settings (Setup Menu)
En-39
Level Calibration
Adjust the level of each speaker with the built-in test tone� Settings are automatically
configured if you use the Automatic Speaker Setup�
Setting Item Default Value Setting Details
Front Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Center 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Front Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Height Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Height Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Surround Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Back Right 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Back Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● This setting cannot be changed if
"Configuration" - "Powered Zone 2" is set to
"Yes" and Zone2 is set to on�
Setting Item Default Value Setting Details
Surround Left 0 dB Select a value between "-12 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
Subwoofer 0 dB Select a value between "-15 dB" and "+12 dB"�
A test tone will be output each time you change
the value� Select the desired level�
● The speaker "Level Calibration" may be unable to be changed depending on the settings in
"Configuration" - "Speaker Channels" / "Subwoofer"�
● "Level Calibration" cannot be changed while muting is on�
Equalizer Settings
Adjust the output volume of each range of each connected speaker� You can adjust the
volume of each range of each speaker� You can set three types of equalizer settings in the
Presets 1, 2, and 3�
● You can adjust the bass in the low range frequencies (63 Hz, etc�), and the treble in the high range
frequencies (16 kHz, etc�)�
● You can select up to seven frequency bands for each speaker�
Setting Item Default Value Setting Details
Front 0 dB First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the
/ cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
Center 0 dB First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the
/ cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
Height 0 dB First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the
/ cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".
● This cannot be selected if "Configuration" -
"Powered Zone 2" is set to "Yes" and Zone2
is set to on�
Surround 0 dB First select the frequency of the speaker from
"25 Hz" to "16 kHz" with the
/ cursors, then
use / to adjust the volume of the frequency
between "−6dB" to "+6dB".