Owner's Manual

51
En
Analog Audio Input
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player.
■ Subwoofer Input Sensitivity
` 0dB
to 15dB in 5 dB step.
Note
• This setting only affects signals connected to the AV receiver’s
multichannel input SUBWOOFER jack.
• If you find that your subwoofer is too loud, try the 10 dB or
15 dB setting.
Main menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ Room Correction and Speaker Setup
function, or set them manually, which is useful if you
change one of the connected speakers after using
Audyssey MultEQ Room Correction and Speaker Setup
function.
Note
• These settings are disabled when:
– a pair of headphones is connected, or
–the “Audio TV Out” setting is set to “On” (➔ 62) and an
input selector other than HDMI is selected.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“Speakers Type(Front)” setting (➔ 51).
For hookup information, see “Bi-amping the Front Speak-
ers” (➔ 15).
Note
• When bi-amping is used, the AV receiver is able to drive up to
5.1 speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms
:
Select if the impedances of all speakers are between
6 and 16 ohms.
■ Speakers Type(Front)
` Normal:
Select this if you’ve connected your front speakers
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers.
Note
• Powered Zone 2 cannot be used if “Speakers Type(Front)” is
set to “Bi-Amp” (➔ 79).
■ Powered Zone 2
See “Setting the Powered Zone 2” (➔ 79).
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
` Yes
:
Select if a subwoofer is connected.
` No:
Select if no subwoofer is connected.
■ Front
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
to 130Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center
*1
, Surround
*1
, Surr Back
*2*3*4*5
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
to 130Hz, 150Hz, 200Hz
` None:
Select if no speaker is connected.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
®
Room Correction and Speaker
Setup function (➔ 28).
If you change these settings, you must run
Audyssey MultEQ Room Correction and Speaker
Setup again (➔ 28).
This setting is set automatically by Audyssey MultEQ
Room Correction and Speaker Setup function (➔ 28).