Owner's Manual
Table Of Contents
- Safety Information and Introduction
- Connections
- Turning On & Basic Operations
- Turning On/Off the AV Receiver
- Initial Setup
- Playback
- Playing the Connected Component
- Controlling Contents of USB or Network Devices
- Understanding Icons on the Display
- Playing an iPod/iPhone via USB
- Playing a USB Device
- Listening to vTuner Internet Radio
- Registering Other Internet Radio
- Changing the Icon Layout on the Network Service Screen
- Playing Music Files on a Server (DLNA)
- Remote Playback
- Playing Music Files on a Shared Folder
- Listening to AM/FM Radio
- Playing Audio and Video from Separate Sources
- Using Basic Functions
- Advanced Operations
- Controlling Other Components
- iPod/iPhone Playback via Onkyo Dock
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Codes
- Entering Remote Control Codes
- Remapping Colored Buttons
- Remote Control Codes for Integra/Onkyo Components Connected via RI
- Resetting the Remote Mode Buttons
- Resetting the Remote Controller
- Controlling Other Components
- Learning Commands
- Using Normal Macros
- Appendix
Appendix
En-100
Connection Tips and
Video Signal Path
The AV receiver supports several connection formats for
compatibility with a wide range of AV equipment. The
format you choose will depend on the formats supported by
your components. Use the following sections as a guide.
Video components can be connected by using any one of
the following video connection formats: composite video,
PC IN (Analog RGB), component video, or HDMI, the
latter offering the best picture quality.
The AV receiver can upconvert between video formats,
depending on the “Monitor Out” setting (➔ page 55),
which generally determines whether video signals are
upconverted for the component video output or the HDMI
output.
Tip
• For optimal video performance, THX recommends that video
signals pass through the system without upconversion (e.g.,
component video input passing through to component video
output).
• To by-pass the upconversion, set the “Picture Mode” setting to
“Direct” (➔ page 68).
■ “Monitor Out” set to “Main” or “Sub”
Video input signals flow through the AV receiver as
shown, with composite video, PC IN (Analog RGB), and
component video sources all being upconverted for the
HDMI output. Use these settings if you connect either
HDMI OUT MAIN or HDMI OUT SUB of the AV
receiver to your TV.
The composite video and component video outputs pass
through their respective input signals as they are.
When you connect a video component to an HDMI,
COMPONENT or COMPOSITE input, you must assign
that input to an input selector (➔ page 56, 57).
■ “Monitor Out” set to “Both”
Video input signals flow through the AV receiver as
shown, with composite video, PC IN (Analog RGB), and
component video sources all being upconverted for both
HDMI outputs. Use this setting if you connect both
HDMI OUT MAIN and HDMI OUT SUB of the AV
receiver to your TV.
Note that video signals are output from both HDMI outputs
at the resolution supported by both TVs.
The composite video and component video outputs pass
through their respective input signals as they are.
When you connect a video component to an HDMI,
COMPONENT or COMPOSITE input, you must assign
that input to an input selector (➔ page 56, 57).
Note
• When “Monitor Out” is set to “Both”, the “Resolution” setting
cannot be selected.
The on-screen setup menus appear only on a TV that
is connected to HDMI OUT MAIN. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
Video Connection Formats
IN
MONITOR OUT
Blu-ray Disc/DVD player, etc.
AV receiver
TV, projector, etc.
Composite
Composite
Component
Component
Video Signal Flow Chart
HDMIPC IN
(Analog RGB)
HDMI
IN
MONITOR OUT
Blu-ray Disc/DVD player, etc.
AV receiver
TV, projector, etc.
Composite
Composite
Component
Component
Video Signal Flow Chart
HDMI
HDMI
PC IN
(Analog RGB)