Owner's Manual

Advanced Operations
En-59
■ Front
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center
*1
, Surround
*1*2
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Front Wide
*1*3*4*6*8
, Front High
*1*3*5*6*7*8
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Surround Back
*1*2*3*5*6*8
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
When the “Powered Zone 3” setting is set to “Yes” and
Zone 3 is turned on, this setting cannot be selected.
*3
This setting cannot be selected if the “Speakers Type
(Front)” setting is set to “Bi-Amp” or “Digital Crossover”.
*4
When the “Powered Zone 2” setting is set to “Yes”, this
setting cannot be selected.
*5
When the “Powered Zone 2” setting is set to “Yes” and
Zone 2 is turned on, this setting cannot be selected.
*6
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*7
When the “Powered Zone 3” setting is set to “Yes”, this
setting cannot be selected.
*8
If the “Preout to External Amplifier” setting is enabled for
these speakers, “None” cannot be selected.
■ Surround Back Ch
` 1ch:
Select if only one surround back speaker L is
connected.
` 2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
• If the “Surround Back” setting is set to “None”, this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 110Hz, 120Hz
` Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency of
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
Note
• If you’re using THX-certified speakers, select “80Hz”.
■ Subwoofer Phase
` 0
º
` 180º:
Moves the subwoofer phase.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot be
selected.
■ Double Bass
` On
` Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to
the subwoofer.
Note
• When the “Subwoofer” setting is set to “No” or the “Front”
setting to anything other than “Full Band”, this setting is fixed to
“-----”.
• This setting is set to “On” automatically when the “Subwoofer”
and “Front” settings are set for the first time to “Yes” and “Full
Band” respectively.
• If you’re using THX-certified speakers, select “Off(THX)”.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer intended.
■ Unit
` feet:
Distances can be set in feet. Range: 0.2ft to 30.0ft in
0.2 foot steps.
` meters:
Distances can be set in meters. Range: 0.06m to
9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
This setting is NOT set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup (➔ page 35).
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup (➔ page 35).