Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
102
Advanced Setup—Continued
Some of the settings in this section are set automatically by Audyssey MultEQ
®
XT Room Correction and Speaker
Setup (see page 58).
Here you can check the settings made by Audyssey MultEQ
®
XT Room Correction and Speaker Setup, or set them
manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ
®
XT Room Cor-
rection and Speaker Setup.
Note:
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
Speaker Setup
1
Press the [Receiver] button followed by
the [Setup] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
2
Use the Up and Down [q]/[w] buttons to
select “2. Speaker Setup”, and then press
[Enter].
3
Use the Up and Down [q]/[w] buttons to
select the submenu, and then press
[Enter].
4
Use the Up and Down [q]/[w] buttons to
select setting, and then use the Left and
Right [e]/[r] buttons to set them.
5
When you’ve finished, press the [Setup]
button.
The setup menu closes.
Speaker Settings
See “Speaker Settings” on page 54.
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify
“Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good
sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be
output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover
frequencies.
If you set up your speakers using Audyssey MultEQ
®
XT Room Correction and Speaker Setup, please make sure
manually that any THX speakers are set to “80Hz(THX)” crossover.
Subwoofer
*1
1ch: Audio signal is outputted from SW1 jack only.
2ch: Audio signal is outputted from SW1 and SW2 jacks (default).
No: Select if no subwoofer is connected.
Front
*2
Full Band, 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX) (default), 90Hz,
100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Center
*3
Surround
*3
Front Wide
*3*5*6*8
Front High
*3*5*6*7
Surr Back
*6*8*10
Full Band, 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz,
120Hz, 130Hz, 150Hz, 200Hz
None: Select if no speaker is connected.
Surr Back Ch
*11
1ch: Select if only one surround back L speaker is connected.
2ch: Select if two (left and right) surround back speakers are connected (default).