Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
125
Advanced Setup—Continued
Speaker Levels
You can adjust the volume of each speaker while listening to an input source.
These temporary adjustments are cancelled when the AV receiver is set to Standby. To save the setting you made here,
go to “Level Calibration” on page 103 before setting the AV receiver to Standby.
Subwoofer 1
–15.0 dB to +12.0 dB (default: 0.0 dB)
Subwoofer 2
–15.0 dB to +12.0 dB (default: 0.0 dB)
Center –12.0 dB to +12.0 dB (default: 0.0 dB)
Notes:
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to “No” or “None” in the “Speaker Configuration” cannot be adjusted (see page 102).
• This function will not work when the Direct listening mode is selected to play analog audio.
Audio Selector
You can set priorities of audio output when there are both digital and analog inputs.
Audio Selector Auto: The AV receiver gives priority to analog signals when there is no digital input
(default).
Multich: The AV receiver always outputs analog signals from multichannel analog input.
Analog: The AV receiver always outputs analog signals.
Note:
This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL
IN. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) are assigned, HDMI
input will be selected as a priority by setting to “Auto”. To select the digital audio input, see “Digital Audio
Input Setup” on page 53.
A/V Sync
See “A/V Sync” of “Source Setup” on page 110.