Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
22
Connecting the AV receiver—Continued
The FRONT L/R and SURR BACK/ZONE 3 L/R ter-
minal posts can be used with front speakers and surround
back speakers respectively, or bridged together to pro-
vide almost double the output power for the front
speakers.
• When bridging is used, surround back speakers cannot
be used.
• For bridging, the positive (+) FRONT L/R and SURR
BACK/ZONE 3 L/R terminal posts are used, but the
negative (–) FRONT L/R and SURR BACK/ZONE 3
L/R terminals are not.
• Once you’ve completed the bridging connections
shown below and turned on the AV receiver, you must
set the “Speakers Type(Front)” setting to “BTL” to
enable bridging (see page 54).
Notes:
• Use only front speakers with an impedance of 8
ohms or higher for bridging. Failure to do so may
seriously damage the AV receiver.
• When using bridging, make sure that your front speak-
ers can handle the additional power.
Bridged Speaker Hookup
Bridging the Front Speakers
1
Connect the AV receiver’s FRONT R positive (+)
terminal to the right speaker’s positive (+) ter-
minal. And connect the AV receiver’s SURR
BACK/ZONE 3 R positive (+) terminal to the
right speaker’s negative (–) terminal.
2
Connect the AV receiver’s FRONT L positive (+)
terminal to the left speaker’s positive (+) terminal.
And connect the AV receiver’s SURR
BACK/ZONE 3 L positive (+) terminal to the left
speaker’s negative (–) terminal.
Right speaker Left speaker