Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
63
First Time Setup—Continued
The speaker type detected does not match what was
expected. The speaker may be incorrect type or bro-
ken. Please check that it is the correct speaker type.
❏ Speaker Matching Error!
The number of speakers detected on the second mea-
surement and later was different to the number
detected on the first measurement.
Make sure speakers that could not be detected are
connected properly.
Retry: Return to step 2 and try again.
Cancel: Cancel the room correction and speaker setup.
❏ Writing Error!
This message appears if saving fails.
Try saving again. If this message appears after 2 or 3
attempts, the AV receiver is probably malfunctioning.
Contact the dealer from whom you purchased this unit.
Retry: Return to step 2 and try again.
Cancel: Cancel the room correction and speaker setup.
Changing the Speaker Settings Manually
If you wish to make changes to the settings found during
the room correction and speaker setup, follow the
directions on pages 102 to 105.
Notes:
• Please note that THX recommends any THX main
speakers be set to “80Hz(THX)”. If you set up your
speakers using Audyssey MultEQ XT Room
Correction and Speaker Setup, please make sure
manually that any THX speakers are set to 80 Hz
(THX) crossover (see page 102).
• Sometimes due to the electrical complexities of
subwoofers and the interaction with the room, THX
recommends setting the level and the distance of the
subwoofer manually.
• Sometimes due to interaction with the room, you may
notice irregular results when setting the level and/or
distance of the main speakers. If this happens, THX
recommends setting them manually.
Using Powered Subwoofers
If you’re using powered subwoofers that output very
low-frequency sound at a low volume level, it may not be
detected by Audyssey MultEQ
®
XT Room Correction
and Speaker Setup.
If the “Subwoofer” appears on the “Review SP
Configuration” screen as “No”, increase the subwoofer’s
volume to the half-way point, set it to its highest
crossover frequency, and then try running
Audyssey MultEQ XT Room Correction and Speaker
Setup again. Note that if the volume is set too high and
the sound distorts, detection issues may occur, so use an
appropriate volume level. If the subwoofer has a low-
pass filter switch, set it to Off or Direct. Refer to your
subwoofer’s instruction manual for details.
FL : Error
SL : Yes
FWL : ---
FHL : ---
SBL : Yes
C : Yes
FR : Yes
SR : Yes
FWR : ---
FHR : ---
SBR : Yes
SW1 : Yes
SW2 : Yes
MultEQ XT: Auto Setup
Retry
Cancel
Speaker Detect Error
MultEQ XT: Auto Setup
Retry
Cancel
Speaker Matching Error!
MultEQ XT: Auto Setup
Retry
Cancel
Writing Error!