AV Receiver DTR-80.2 DTR-70.
Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not user-serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water.
Thank you for purchasing an Integra AV receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver. Please retain this manual for future reference.
Contents Introduction Important Safety Instructions ......................................... 2 Precautions....................................................................... 3 Supplied Accessories...................................................... 4 Using the Remote Controller .......................................... 4 Features ............................................................................ 6 Front & Rear Panels......................................................... 8 Front Panel...
Features Amplifier Connections (DTR-80.2) • 145 Watts/Channel @ 8 ohms (FTC) • 220 Watts/Channel @ 6 ohms (IEC) • 280 Watts/Channel @ 6 ohms (JEITA) (DTR-70.2) • 140 Watts/Channel @ 8 ohms (FTC) • 200 Watts/Channel @ 6 ohms (IEC) • 250 Watts/Channel @ 6 ohms (JEITA) • 8 HDMI*8 Inputs (1 on front panel) and 2 Outputs • Integra/Onkyo p for System Control • (DTR-80.2) 7 Digital Inputs (4 Optical/3 Coaxial) • (DTR-70.
*10 *1 HD Radio™ and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation. To receive HD Radio broadcasts, you must install an Onkyo UP-HT1 HD Radio tuner module (sold separately). THX and the THX logo are trademarks of THX Ltd. which may be registered in some jurisdictions. All rights reserved. *2 “x.v.Color” is a trademark of Sony Corporation. *11 *3 Manufactured under license under U.S.
Front & Rear Panels Front Panel North American models a b cdefg h i uvw x yz j k l m n o pq r s B A Australian models C t D E The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item.
A Input selector buttons (BD/DVD, VCR/DVR, CBL/SAT, Game, PC, AUX, Tape, Tuner, TV/CD, Phono, Port and NET/USB) (➔ 25) C AUX Input HDMI jack (➔ 18) B USB port (➔ 81, 91) E RT/PTY/TP button (Australian models) (➔ 39) D AUX Input jacks (Video, Audio L/R and Digital) (➔ 19) Display a bc d e i j kl m f g h n o pq For detailed information, see the pages in parentheses.
Rear Panel Illustration is based on DTR-80.2. North American models a bc d f g e p q h i r a UNIVERSAL PORT jack b IR IN (A/B) and OUT jacks c DIGITAL IN COAXIAL and OPTICAL jacks d USB port (DTR-80.2) e ETHERNET port f u REMOTE CONTROL jack g RS232 terminal Terminal for control.
Remote Controller Controlling the AV Receiver To control the AV receiver, press Receiver to select Receiver mode. You can also use the remote controller to control Integra/Onkyo Blu-ray Disc/DVD player, CD player and other components. See “Entering Remote Control Codes” for more details (➔ 98). a b j c d For detailed information, see the pages in parentheses.
About Home Theater Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With Blu-ray Discs or DVDs, you can enjoy DTS and Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).
Connections Connecting the AV Receiver Speaker Connection Precautions Connecting Your Speakers Speaker Configuration The following table indicates the channels you should use depending on the number of speakers that you have. For 9.2-channel surround-sound playback, you need 9 speakers and 2 powered subwoofers.
Connecting the Speaker Cables Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. 1/2" to 5/8"(12 to 15 mm) Using Banana Plugs (North American models) • If you are using banana plugs, tighten the speaker terminal before inserting the banana plug. • Do not insert the speaker code directly into the center hole of the speaker terminal.
Using Dipole Speakers You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers should be positioned so that their arrows point toward the TV/screen, while the surround back dipole speakers should be positioned so that their arrows point toward each other, as shown.
Bridging the Front Speakers The FRONT L/R and SURR BACK/ZONE 3 L/R terminal posts can be used with front speakers and surround back speakers respectively, or bridged together to provide almost double the output power for the front speakers. • When bridging is used, surround back speakers cannot be used. • For bridging, the positive (+) FRONT L/R and SURR BACK/ZONE 3 L/R terminal posts are used, but the negative (–) FRONT L/R and SURR BACK/ZONE 3 L/R terminals are not.
About AV Connections Connected image with AV components HDMI cable Other cables : Video & Audio Blu-ray Disc/DVD player : Audio AV receiver AV receiver TV, projector, etc. : Video Game console TV, projector, etc. Blu-ray Disc/DVD • Before making any AV connections, read the manuals supplied with your AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections.
Connecting Your Components with HDMI VCR or DVD recorder/Digital Video Recorder Game console TV, projector, etc. Personal computer Blu-ray Disc/DVD player Camcorder Satellite, cable, set-top box, etc. Connect your components to the appropriate jacks. The default input assignments are shown below. ✔: Assignment can be changed (➔ 51 to 52).
Connecting Your Components Front A Rear C E *1 B D F G Connect your components to the appropriate jacks. The default input assignments are shown below. ✔: Assignment can be changed (➔ 52, 53). No. Jack A AUX Input B C COMPONENT VIDEO DIGITAL Signal Components Video Composite video Camcorder, etc Audio L/R Analog audio Digital Digital audio IN 1 (BD/DVD) Component video Blu-ray Disc/DVD player ✔ IN 2 (CBL/SAT) Satellite, cable, set-top box, etc.
Note *1 DTR-80.2 Connect a turntable (MM) that has built-in a phono preamp to TV/CD IN or connect it to PHONO IN with the phono preamp turned off. If your turntable (MM) doesn’t have a phono preamp, connect to PHONO IN. If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable’s manual for details. If your turntable has a ground wire, connect it to the AV receiver’s GND screw.
Connecting Antenna This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Caution (North American models) Insert the plug fully into the jack. (Australian models) • Be careful that you don’t injure yourself when using thumbtacks. Insert the plug fully into the jack. Push. Insert wire. Release. Assembling the AM loop antenna.
Which Connections Should I Use? The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide. Video Connection Formats Video component can be connected by using any one of the following video connection formats: composite video, S-Video, PC IN (Analog RGB), component video or HDMI, the latter offering the best picture quality.
■ “Monitor Out” setting set to “Analog” Video input signals flow through the AV receiver as shown, with composite video, S-Video and PC IN (Analog RGB) sources being upconverted for the component video output. Use this setting if you connect the AV receiver’s COMPONENT VIDEO MONITOR OUT to your TV. Composite video is upconverted to S-Video and S-Video is downconverted to composite video. Note that these conversions only apply to the MONITOR OUT V and S outputs, not the VCR/DVR OUT V and S outputs.
Turning On & Basic Operations Turning On/Off the AV Receiver On/Standby Standby indicator Standby On Receiver Turning On Press On/Standby on the front panel. or Press Receiver followed by On on the remote controller. The AV receiver comes on, the display lights, and the Standby indicator goes off. Pressing the remote controller’s On again will turn on any components connected via u. Turning Off Press On/Standby on the front panel. or Press Receiver followed by Standby on the remote controller.
Basic Operations This manual describes the procedure using the remote controller unless otherwise specified. Selecting the Language Used for the Onscreen Setup Menus Displaying Source Information You can display various information about the current input source as follows. (Components connected to the UNIVERSAL PORT jack are excluded.) Press Receiver followed by Display repeatedly to cycle through the available information. You can determine the language used for the onscreen setup menus.
Muting the AV Receiver You can temporarily mute the output of the AV receiver. Press Receiver followed by Muting. The output is muted and the MUTING indicator flashes on the display. Tip • To unmute, press Muting again or adjust the volume. • The Mute function is cancelled when the AV receiver is set to Standby. Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.
Using the Home Menu Note *1 The Home menu provides you quick access to frequently used menus without having to go through the long standard menu. This menu enables you to change settings and view the current information. 1 *2 Press Receiver followed by Home. The following information will be superimposed on the TV screen. (The language is English only.
Changing the Input Display When you connect an u-capable Onkyo component, you must configure the input display so that u can work properly. This setting can be done only from the front panel. 1 Press Tape, Game or VCR/DVR so that “TAPE”, “GAME” or “VCR/DVR” appears on the display. Using Activities to Start Easy Macros You can use Activities to execute a number of remote control operations with a single button. This button has the following two modes.
Turning Off the Components Press All Off. The playback component assigned to the last-pressed Activities, the AV receiver, and the TV turn off.*2 *2 When the last-pressed Activities is My Music, the TV will not turn off. Changing the Playback Components Assigned to Activities You can change the playback components assigned to the Activities of Easy Macro mode using the following procedure.
4 TV Caution def cab • When the “Subwoofer” setting is set to “1ch”, the left-hand subwoofer (SW1) alone will be measured. When the “Subwoofer” setting is set to “1ch” with two subwoofers connected, the right-hand subwoofer (SW2) will not be measured and no sound will be output. • An error will occur if you set “Subwoofer” to “2ch” without connecting any subwoofers, or with only one subwoofer connected. gh : Listening area a to h: Listening position Note • Make the room as quiet as possible.
Tip Note 9 • You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using e/r. Disconnect the speaker setup microphone. Note • When Audyssey MultEQ® XT32 Room Correction and Speaker Setup is complete, the “Equalizer” will be set to “Audyssey” (➔ 56). The Audyssey indicator will light (➔ 9). • You can cancel Audyssey MultEQ XT32 Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.
Listening to the Radio This section describes the procedure using the buttons on the front panel unless otherwise specified. ■ Manual tuning mode 1 2 Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. You can change the frequency steps (➔ 67). Press and hold Tuning q/w. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.
Presetting FM/AM Stations You can store a combination of up to 40 of your favorite FM/AM radio stations as presets. 1 2 Tune into the FM/AM station that you want to store as a preset. See the previous section. Press Memory. The preset number flashes. (Actual display depends on the country.) 3 4 While the preset number is flashing (about 8 seconds), use Preset e/r to select a preset from 1 through 40. Press Memory again to store the station or channel.
Setting Up the SiriusConnect™ Home Tuner The optional SiriusConnect Home tuner kit includes everything for easy home installation, including the SiriusConnect receiver, indoor/outdoor antenna with 21-foot cable, 8-pin mini DIN connector cable, and an AC power adapter. See the SiriusConnect Home tuner’s instructions for more information. Use the 8-pin mini DIN connector cable to connect the SiriusConnect receiver to the SIRIUS jack on the rear of the AV receiver.
4 Use q/w to select “SAT Radio Mode”, and e/r to select “SIRIUS”. Pressing e/r cycles through the following options: ` None: Select if you’re not using Satellite Radio. ` SIRIUS: Select to use SIRIUS Satellite Radio. 5 There are three ways to select SIRIUS Satellite Radio channels: 1. Channel Search mode: select any channel. 2. Category Search mode: select channels by category. 3. Direct tuning: enter channel number. ■ Channel Search mode 7–3.
■ Selecting the previously selected channel Press Return to select the previously selected channel. Selecting Channels on the AV Receiver 1 2 3 4 Press Tuner repeatedly to select “SIRIUS”. Press Tuning Mode repeatedly to select Channel Search mode or Category Search mode. 1 2 Press Receiver followed by Setup. The main menu appears onscreen. Use q/w to select “Hardware Setup”, and then press Enter. The “Hardware Setup” menu appears. 7. Hardware Setup Use Tuning q/w to select a channel.
6 7 8 9 Use q/w to select “Parental Lock”, and then press Enter. The channel number, channel name, and the current status are displayed. 5 Repeat this for each of the four digits in the PIN number. If you’re entering the PIN number for the very first time, the default is “0000”. The following screen appears. Use q/w to select a channel, and e/r to select “Locked” or “Unlocked”. Press Enter to save your changes, or press Return to return to the previous screen without saving.
Displaying SIRIUS Satellite Radio Information 5 Position the SiriusConnect Home antenna so that as many bars as possible (up to 3) appear on the Satellite signal strength meter. Press Display repeatedly to cycle through the available information.
Using RDS (Australian models) Finding Stations by Type (PTY) You can search for radio stations by type. RDS works only in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator lights. What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days.
■ RDS program types (PTY) Type En 40 Display None None News reports News Current affairs Affairs Information Info Sport Sport Education Educate Drama Drama Culture Culture Science and technology Science Varied Varied Pop music Pop M Rock music Rock M Middle of the road music Easy M Light classics Light M Serious classics Classics Other music Other M Weather Weather Finance Finance Children’s programmes Children Social affairs Social Religion Religion Phone in P
Recording This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources. Connecting a Recording Component Recording Separate AV Sources Here you can record audio and video from completely separate sources, allowing you to overdub audio onto your video recordings. This function takes advantage of the fact that when an audio-only input source (TV/CD, Phono, etc.
Using the Listening Modes Selecting Listening Modes See “About Listening Modes” for detailed information about the listening modes (➔ 43). Listening Mode Buttons Press Receiver first. Movie/TV, Music, Game Music Movie/TV Game THX Movie/TV button This button selects the listening modes intended for use with movies and TV. Music button This button selects the listening modes intended for use with music. Game button This button selects the listening modes intended for use with video games.
About Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Explanatory Notes ij ab Sp Layout c Listening Mode de gh kl f a b Front speakers c Center speaker d e Surround speakers f Subwoofer(s) g h Surround back speakers i j Front high speakers k l Front wide speakers ■ Input Source The following audio formats are supported by the listening mode. A This is mono (monophonic) sound.
Listening Modes Listening Mode Description Input Source Direct Speaker Layout In this mode, audio from the input source is output without surround-sound A processing. The speaker configuration (presence of speakers), speaker dis- S D i r e c t d i oPPoPP tances and A/V Sync settings are enabled, but much of the processing set via D Home is disabled. See “Advanced Setup” for more details (➔ 49).
Listening Mode Description Input Source Speaker Layout DTS-HD High Resolution Audio (Continued from the previous page.) D xcn m F xcn*1 m*1 D xcn F xcn*1 m*1 S D xcn m D xcn m This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.
Listening Mode THX THX N TH eX o THX N TH eX o THX THX THX Description Input Source Founded by George Lucas, THX develops stringent standards that ensure D movies are reproduced in movie theaters and home theaters just as the direc- F C i n ema tor intended. THX Modes carefully optimize the tonal and spatial character- G istics of the soundtrack for reproduction in the home-theater environment. :M 6 ut sr i cx t e x t e They can be used with 2-channel matrixed and multichannel sources.
Listening Mode Description Input Source Neural Surround*5 This mode employs psychoacoustic frequency domain processing, which S allows delivery of a more detailed sound stage, with superior channel separaNR L S u r r o u n d tion and localization of audio elements. The Neural Surround modes can expand any 2-channel stereo source for 5.1- or 7.1-channel playback, respec- D NR L T HX C i n ema tively.
Onkyo-Original DSP Listening Modes Listening Mode Description Orchestra Suitable for classical or operatic music, this mode emphasizes the surround A channels in order to widen the stereo image, and simulates the natural rever- S beration of a large hall. D Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the F front stereo image, giving the impression of being right in front of the stage.
Advanced Operations Advanced Setup On-screen Setup Menus Common Procedures in Setup Menu This manual describes the procedure using the remote controller unless otherwise specified. Receiver MENU a b c d e f g h i 1. 2. 3. 4. 5. 6. 7. 8. 9. a Input/Output Assign (➔ 50) f Miscellaneous (➔ 66) 1. Input/Output Assign 1. 2. 3. 4. 5. Monitor Out HDMI Input Component Video Input Digital Audio Input Analog Audio Input b Speaker Setup (➔ 53) 6. Miscellaneous 1. 2. 3. 4. 5.
Explanatory Notes a b c Note Main Menu Speaker Setup ■ Subwoofer ` 1ch: Audio signal is outputted from SW1 jack only. ` 2ch: Audio signal is outputted from SW1 and SW2 jacks.
■ Resolution You can specify the output resolution for the HDMI output and COMPONENT VIDEO MONITOR OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV. `Through*1: Select this to pass video through the AV receiver at the same resolution and with no conversion. `Auto*2: Select this to have the AV receiver automatically convert video at resolutions not supported by your TV.
Note • For composite video, S-Video, and component video upconversion for the HDMI output, the “Monitor Out” setting must be set to other than “Analog” (➔ 50), and the “HDMI Input” setting must be set to “- - - - -”. See “Video Connection Formats” for more information on video signal flow and upconversion (➔ 22). • If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of “Component Video Input”.
Digital Audio Input Note If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPT 1” to the “TV/CD” input selector. Here are the default assignments.
■ Speaker Impedance ` 4ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. ` 6ohms: Select if the impedances of all speakers are between 6 and 16 ohms. Note • When bridging is used, “Speaker Impedance” setting is fixed at “8ohms”. ■ Speakers Type(Front) ` Normal: Select this if you’ve connected your front speakers normally. ` Bi-Amp: Select this if you’ve connected your front speakers for bi-amped operation. The Bi AMP indicator will light (➔ 9).
■ Front `Full Band `40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz Note • If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”. ■ Center*1, Surround*1*2, Surround Back*3*4*5*8 `Full Band `40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz `None: Select if no speaker is connected.
Level Calibration This setting is set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup function (➔ 29). Equalizer Settings This setting is set automatically by Audyssey MultEQ XT32 Room Correction and Speaker Setup function (➔ 29). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. With the Equalizer settings, you can adjust the tone of speakers individually with a 15-band equalizer.
THX Audio Setup With the “Surr Back Speaker Spacing” setting, you can specify the distance between your surround back speakers. If you’re using a THX-certified subwoofer, set the “THX Ultra2/Select2 Subwoofer” setting to “Yes”. You can then apply THX’s Boundary Gain Compensation (BGC) to compensate the perceived exaggeration of low frequencies for listeners sitting very close to a room boundary (i.e., wall). You can also set the THX Loudness Plus.
Input Channel ` Left + Right: Both the left and right channels are output. ` Left: Only the left channel is output. ` Right: Only the right channel is output. Output Speaker ` Center: Mono audio is output by the center speaker. ` Left / Right: Mono audio is output by the front left and right speakers. This setting determines which speakers output mono audio when the Mono listening mode is selected. Note • If the “Center” setting is set to “None” (➔ 55), this setting is fixed at “Left / Right”.
■ Volume Leveler `Off: Volume Leveler off. `Low: Low Compression Mode becomes active. `Mid: Medium Compression Mode becomes active. `High: High Compression Mode becomes active. This setting affects volume the most, causing all sounds to be of equal loudness. “Volume Leveler” maintains the perceived loudness of all content for example, from different channels or input sources. Note • If the “Dolby Volume” setting is set to “Off”, this setting cannot be selected. ■ Half Mode `Off: Half Mode off.
Direct ■ Analog Subwoofer ` Off: Analog audio signals (bass signals) are not output. ` On: Analog audio signals (bass signals) are output. This setting determines whether or not analog audio signals (bass signals) are output from front speakers when the Direct listening mode is selected. Note • If the “Subwoofer” setting is set to “No” (➔ 54), this setting cannot be selected. ■ DSD DAC Direct ` Off: DSD signals are processed by the DSP. ` On: DSD signals are not processed by the DSP.
■ Dynamic Volume `Off: Audyssey Dynamic Volume® off. `Light: Light Compression Mode becomes active. `Medium: Medium Compression Mode becomes active. `Heavy: Heavy Compression Mode becomes active. This setting affects volume the most, causing all sounds to be of equal loudness.
IntelliVolume Name input area ■ IntelliVolume ` –12dB to 0dB to +12dB in 1 dB steps. With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others. Use e/r to set the level. If a component is noticeably louder than the others, use e to reduce its input level. If it’s noticeably quieter, use r to increase its input level.
Picture Adjust Using “Picture Adjust”, you can adjust the picture quality and reduce any noise appearing on the screen. To view the TV picture while setting, press Enter. To return to the previous screen, press Return. ■ Game Mode `Off: Game Mode off. `On: Game Mode on. If video signal delay occurs during playback on a video component (i.e. game console), select the corresponding input source and set the “Game Mode” setting to “On”. The delay will decrease but in return the picture quality will become poor.
■ Mosquito NR*2*3*4*6 ` Off: Mosquito noise reduction off. ` Low: Low mosquito noise reduction. ` Mid: Medium mosquito noise reduction. ` High: High mosquito noise reduction. With Mosquito Noise Reduction, you can remove the shimmering or haziness that sometimes appears around objects in the picture. Mosquito noise can be an issue with overly compressed MPEG content. ■ Random NR*2*3*4*6 ` Off: Random noise reduction off. ` Low: Low random noise reduction. ` Mid: Medium random noise reduction.
■ Blue Contrast*2*4 `–50 to 0 to +50 With this setting you can adjust blue contrast. “–50” is the least. “+50” is the greatest. Tip *1 *2 This procedure can also be performed on the remote controller by using the Home menu (➔ 27). Press CLR if you want to reset to the default value. Note • If you are using the analog RGB input, the following settings have no effect: “Film Mode”, “Edge Enhancement”, “Mosquito NR”, “Random NR” and “Block NR”.
OSD Setup Miscellaneous Main menu Miscellaneous Volume Setup ■ Volume Display ` Absolute: Display range is “Min”, “0.5” through “99.5”, “Max”. ` Relative(THX): Display range is “–QdB”, “–81.5dB” through “+18.0dB”. With this setting, you can choose how the volume level is displayed. The absolute value 82 is equivalent to the relative value 0 dB. ■ Muting Level ` –QdB (fully muted), –50dB to –10dB in 10 dB steps. This setting determines how much the output is muted when the muting function is used (➔ 26).
Hardware Setup Main menu Hardware Setup Remote ID ■ Remote ID `1, 2, or 3 When several Integra/Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from “1”, to “2” or “3”. HDMI ■ Audio TV Out ` Off: The audio is not output from the HDMI output. ` On: The audio is output from the HDMI output. This preference determines whether the incoming audio signal is output from the HDMI output.
■ HDMI Control(RIHD) ` Off: p disabled. ` On: p enabled. This function allows p-compatible components connected via HDMI to be controlled with the AV receiver (➔ 115 to 116). Note • When set to “On” and close the menu, the name of connected p-compatible components and “RIHD On” are displayed on the AV receiver. “Search…” → “(name)” → “RIHD On” When the AV receiver cannot receive the name of the component, it is displayed as “Player*” or “Recorder*”, etc (“*” means the number of two or more component).
Auto Power Down ■ Auto Power Down `Off: Auto Power Down disabled. `On: Auto Power Down enabled. When “Auto Power Down” is set to “On”, AV receiver will automatically perform STANDBY operation if there is no operation for 30 minutes with no audio and no video signal input. “Auto Power Down” will display on the display and OSD from 30 seconds before the Auto Power Down functions.
Speaker Levels Late Night You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to Standby. To save the setting you made here, go to “Level Calibration” (➔ 56) before setting the AV receiver to Standby.
Screen Centered Dialog Audio Selector “Screen Ctr Dialog” is a function for moving the Center image of dialog etc. upwards through use of the front high speaker to fix the image to the display height. You can set priorities of audio output when there are both digital and analog inputs. ■ Screen Ctr Dialog As the value increases, the Center image moves upwards. `0: Screen Centered Dialog off. `1 to 5: Screen Centered Dialog on.
Setting the Incoming Digital Signal (Fixed Mode) By pressing Enter while selecting “HDMI”, “COAX”, “OPT” in the “Audio Selector”, you can specify the input signal in the Fixed Mode. Pressing Enter again allows you to return to the “Audio Selector” setting. Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.
NET/USB About NET The AV receiver is network-ready, which means you can hook it up to your home network with a standard Ethernet cable and enjoy the music files stored on your computer or media server. If your network is connected to the Internet, you can also enjoy Internet radio.
Listening to Internet Radio Note To receive Internet radio, you must connect the AV receiver to a network with Internet access (➔ 73). You can select Internet radio stations by connecting to the AV receiver from your computer and selecting stations in your Web browser. Preset up to 40 Internet radio stations. Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS).
3 Enter the preset name and Internet address (URL). Display WEB Setup Menu Unit Information Preset Internet Radio Customer Setting Internet Radio Information No 1 4 Name Tuner Internet Radio Network setting Save Refresh 1 2 URL NET/USB Delete 2 Delete 3 Delete Click “Save” to save the Internet radio station. Enter q/w/e/r Registering Presets*1 Once you’ve added a station to the list, simply select it on the Internet Radio screen, and then press Enter to start playback.
4 Use q/w to select an item, and then press Enter. A list of music files appears. All Music Song 1 Song 2 Song 3 My favorite song 1 My favorite song 2 My favorite song 3 My favorite song 4 My favorite song 5 My favorite song 6 My favorite song 7 1 / 10 5 Use q/w to select a music file, and press Enter or 1 to start playback. Playback starts and the following screen appears. My favorite song 1 4 / 10 My favorite song 1 Artist name My favorite album 0:00:00 MP3 128kbps 44.
Supported Audio File Formats For server playback, the AV receiver supports the following music file formats: MP3, WMA, WAV, FLAC, Ogg Vorbis, AAC and LPCM. Not all servers support all formats. ■ MP3 • MP3 files must be MPEG-1/MPEG-2 Audio Layer 3 format with a sampling rate of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and a bit-rate of between 8 kbps and 320 kbps. Incompatible files cannot be played.
Server Requirements The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft Web site. • The computer or media server must be on the same network as the AV receiver.
Using Remote Playback 1 2 5 Start Windows Media Player 12. Before remote playback, setup on Windows Media Player 12 is required. On the product, press NET/USB to select the server screen. A list of media server appears. Adjusting the Volume You can adjust the volume of your AV receiver by adjusting the volume bar in the “Remote playback” window. The default maximum volume for the AV receiver is 82 (0dB). If you wish to change this, enter the maximum volume value from the WEB Setup Menu in your browser.
2 Use q/w to select “Hardware Setup”, and then press Enter. The “Hardware Setup” menu appears. 7. Hardware Setup 1. 2. 3. 4. 5. 6. 7. 3 Remote ID Multi Zone Tuner HDMI Auto Power Down Network Firmware Update Use q/w to select “Network”, and then press Enter. The “Network” screen appears. 7-6. Network MAC Address DHCP IP Address Subnet Mask Gateway DNS Server Proxy URL Proxy Port 4 5 xx : xx : xx − yy : yy : yy Enable aaa.bbb.ccc.ddd aaa.bbb.ccc.ddd aaa.bbb.ccc.ddd aaa.bbb.ccc.
About USB Display USB can be used to play music files stored on USB mass storage devices (e.g., USB flash drives and MP3 players), which can be plugged into the AV receiver’s USB port. NET/USB See “Controlling iPod” for iPod connection (➔ 91). Enter q/w/e/r Return 1, 3, 2, 5, 4, 7, 6 Repeat Random USB port (DTR-80.2) USB port 1 2 Plug your USB mass storage device into the AV receiver’s USB port. (DTR-80.2) Press NET/USB repeatedly to select the “USB(Front)” or “USB(Rear)” screen. (DTR-70.
4 Use q/w to select a music file, and press Enter or 1 to start playback. Playback starts and the following screen appears. Folder1 1/17 02_Song_Track2 Artist Album 00:10 01:12:34 MP3 128kbps 16bit/44.1kHz • To return to the previous menu during playback, press Return. • To stop or pause playback, press 2 or 3, respectively. • To select the next song, press 6. To select the beginning of the current song, press 7. To select the previous song, press 7 twice. • To fast forward the current song, press 4.
Multi Zone In addition to your main listening room, you can also enjoy playback in the other room, or as we call Multi Zone. And, you can select a different source for each room. Connecting Your Zone 2 Speakers to an Amp in Zone 2 Connecting Zone 2 There are two ways you can connect Zone 2 speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an amp in Zone 2. This setup allows 9.
Zone 2 Video Output Connecting Zone 3 The AV receiver features a composite video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone. Hookup • Use a composite video cable to connect the AV receiver’s ZONE 2 OUT V jack to a composite video input on your Zone 2 TV. • Alternatively, use a component video cable to connect the AV receiver’s COMPONENT VIDEO ZONE 2 OUT jacks to a component video input on your Zone 2 TV.
Connecting Your Zone 3 Speakers to an Amp in Zone 3 This setup allows 9.2-channel playback in your main listening room and 2-channel stereo playback in Zone 3, with a different source in each room. Hookup • Use an RCA audio cable to connect the AV receiver’s PRE OUT ZONE 3 L/R jacks to an analog audio input on your Zone 3 amp. • Use an RCA audio cable to connect the AV receiver’s PRE OUT ZONE 3 SUBWOOFER jack to the line input on a powered subwoofer in Zone 3.
Setting the Powered Zone 2/3/4 If you’ve connected your Zone 2/3/4 speakers to the AV receiver, as explained in “Connecting Your Zone 2 Speakers Directly to the AV receiver” (➔ 83), “Connecting Your Zone 3 Speakers Directly to the AV receiver” (➔ 84), or “Connecting Your Zone 4 Speakers Directly to the AV receiver” (➔ 85), you must set the “Powered Zone 2”, “Powered Zone 3” or “Powered Zone 4” setting to “Act” (Activated). 1 Setting the Multi Zone 1 Press Receiver followed by Setup.
■ Zone 2 Power On Volume, Zone 3 Power On Volume, Zone 4 Power On Volume `Last, Min, 1 to 99 or Max (Absolute display) `Last, –QdB, –81dB to +18dB (Relative display) This setting determines what the volume will be for Zone 2/3/4 each time the AV receiver is turned on. To use the same volume level as when the AV receiver was last turned off, select “Last”.
Controlling Zone 2/3/4 with the Remote Controller Adjusting the Volume for Zones On the remote controller, press Zone repeatedly, and then use VOL q/w. Standby On Zone On the AV receiver, press Zone 2, Zone 3 or Zone 4 (the Zone 2/3/4 indicator and Zone 2/3/4 selector on the display flashes) and press Zone Level w/q within 8 seconds. Input Selector Muting Zones Note On the remote controller, press Zone repeatedly, and then press Muting.
Using the 12V Triggers The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for the main room, Zone 2, Zone 3, Zone 4, or any combination of rooms. When triggered, the output from a 12V TRIGGER OUT goes high (+12 volts and 150 milliamperes max. at TRIGGER OUT A; +12 volts and 25 milliamperes max.
Using the Remote Controller in Zone 2/3/4 and Multiroom Control Kits To control the AV receiver with the remote controller while you’re in Zone 2, Zone 3 or Zone 4, you’ll need a commercially available multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s installed inside a cabinet.
Controlling iPod & Other Components Controlling iPod Connecting the iPod Directly to the USB Port USB can be used to play music files stored on iPod/iPhone, which can be plugged into the AV receiver’s USB port. 1 2 Note • (DTR-80.2) Note that the rear-panel USB port does not support iPod/iPhone connection. Press NET/USB repeatedly to select the USB input. Connect the USB cable that comes with the iPod/iPhone to the USB port at the front of the AV receiver.
Extended Mode control The content information is displayed (lists are displayed) on the on-screen, and you can select and manipulate the content while looking at the screen. Top screen list: • • • • • • • • Songs*4 Composers*4 Shuffle Songs*5 Now Playing*6 *4 Playlists*4 Artists*4 Albums*4 Genres*4 *5 *6 Displays a list. Plays all tracks in random order. Displays information about currently playing track. Connecting an Onkyo Dock A No.
Using the Onkyo Dock Dock is sold separately. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod with the latest software, available from the Apple web site. For supported iPod models, see the instruction manual of the Onkyo Dock. UP-A1 Dock With the UP-A1 Dock, you can easily play the music, photo, or movie stored on your Apple iPod through the AV receiver and enjoy great sound.
■ System Function Auto Power On If you press the remote controller’s 1 while the AV receiver is on Standby, the AV receiver will automatically turn on, select your iPod as the input source, and your iPod will start playback. Direct Change If you start iPod playback while listening to another input source, the AV receiver will automatically switch to the input to which the RI Dock is connected.
✔: Available buttons Press the appropriate Remote Mode first. Buttons Playlist e/r g h i b ✔*1 a On, Standby b Top Menu c q/w/e/rEnter j c k u Dock f UP-A1 Dock a a Onkyo Dock ✔*5 ✔ ✔ ✔*3 ✔ d 1, 3, 2, 5, 4, 7, 6 ✔ ✔ ✔ ✔ e Repeat Random Play Mode ✔ ✔ ✔*4 ✔*4 ✔*2 ✔ f Display*6 g Muting ✔ ✔ h Album +/– ✔ ✔ i VOL q/w ✔ ✔ j Menu k Return ✔ ✔ d e • With some iPod models, generations and RI Docks, certain buttons may not work as expected.
Controlling Other Components You can use the AV receiver’s remote controller (RC-772M) to control your other AV components, including those made by other manufacturers. This section explains how to enter the remote control code (with the default underlined) for a component that you want to control: DVD, TV, CD, etc. • Learn commands directly from another component’s remote controller (➔ 102). • Program Activities to perform a sequence of up to 32 remote control actions (➔ 101, 103). 4 8–1.
12 Tip • If you cannot access the database, a message “Cannot connect to database.” will appear. Press Enter to return to the previous step. • If the brand name is not found, use r to select “Not Listed”, and then press Enter. When you did NOT search for the model, the following screen appears. Push any key (except for arrow buttons and Enter) to see if the component responds. The following screen appears. 8–1.
Entering Remote Control Codes You’ll need to enter a code for each component that you want to control. 1 2 Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized by category (e.g., DVD player, TV, etc.). While holding down Remote Mode to which you want to enter a code, press and hold down Display (about 3 seconds). The Remote Mode button lights. Note • Remote control codes cannot be entered for Receiver and Zone.
Resetting Remote Mode Buttons You can reset a Remote Mode to its default remote control code. 1 2 While holding down Remote Mode that you want to reset, press and hold down Home until Remote Mode button lights (about 3 seconds). Within 30 seconds, press Remote Mode again. Remote Mode button flashes twice, indicating that the button has been reset. Each of Remote Mode is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.
✔: Available buttons Press the appropriate Remote Mode first. ✔ ✔ b 9, Input, TV VOL q/w ✔ c Guide Top Menu ✔ j d q/w/e/r Enter ✔ k e Setup ✔ l ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔*1*2 ✔*1 ✔*2 ✔*2 ✔ ✔*2 ✔*2 ✔ Random ✔*1*2 ✔*1 ✔*2 ✔*2 ✔ Play Mode ✔*1*2 ✔*1 ✔*2 ✔ ✔ ✔ ✔ k CH +/– Disc +/– ✔ ✔ ✔ ✔ l PREV CH Menu ✔ m Return n CLR ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ *3 ✔ ✔ ✔*1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ The p function is not supported.
■ Source Power On `Enable: Source component will turn on. `Disable: Source component will not turn on. This option enables the source component to turn on when Activities is pressed. Activities Setup Via onscreen menu, you can specify what actions will be taken by the Easy macro command in the Easy macro mode (➔ 28). 1 Press Receiver followed by Setup. The main menu appears onscreen. ■ Receiver Power On `Enable: The AV receiver will turn on. `Disable: The AV receiver will not turn on.
6 Press Enter. A message for transfer will appear. 8–2. Activities Setup My Movie Now we are ready to transfer data to the remote. Please hold the remote so that it is facing the receiver. Use ENTER button of your remote to activate “OK”. Ready? OK Learning Commands The AV receiver’s remote controller can learn the commands of other remote controllers.
1 Note • The remote controller can learn approximately 70 to 90 commands, although this will be less if commands that use a lot of memory are learned. • Remote controller buttons such as Play, Stop, Pause, and so on are preprogrammed with commands for controlling Integra/Onkyo CD players, cassette decks, and DVD players. However, they can learn new commands, and you can restore the preprogrammed commands at any time by resetting the remote controller (➔ 99).
Others Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased this unit. To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press On/Standby.
■ Only the center speaker produces sound If you use the Dolby Pro Logic IIx Movie, Dolby Pro — Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker. In the Mono listening mode, only the front speakers 58 output sound if the “Output Speaker” setting is set to “Center”. Make sure the speakers are configured correctly.
■ The beginning of audio received by an HDMI IN can’t be heard Since it takes longer to identify the format of an — HDMI signal than it does for other digital audio signals, audio output may not start immediately. Video Make sure that all video connecting plugs are pushed 17 in all the way.
■ Can’t control other components Music Server and Internet Radio If it’s an Integra/Onkyo component, make sure that 20 the u cable and analog audio cable are connected properly. Connecting only an u cable won’t work. ■ Can’t access the server or Internet radio Make sure you’ve selected the correct remote controller mode. 11, 99 Check the network connection between the AV receiver and your router or switch.
Others ■ Stand-by power consumption In the following cases, the power consumption may 68, 79, reach up to a maximum of 30W (DTR-80.2)/ 93 90W (DTR-70.2): 1. You are using the Universal Port jack. 2. “Control” is set to “Enable” in the “Network” setting. 3. “HDMI Control(RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter Standby mode as usual.
Important Note Regarding Video Playback The AV receiver can upconvert component video, S-Video, and composite video sources for display on a TV connected to the HDMI output. However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether. In this case, try the following: 1 If the video source is connected to a component video input, connect your TV to the COMPONENT VIDEO MONITOR OUT.
Specifications (DTR-80.2) Amplifier Section Tuner Section Rated Output Power All channels: FM Tuning Frequency Range (North American) 87.5 MHz - 107.9 MHz (Australian) 87.5 MHz - 108.0 MHz, RDS AM Tuning Frequency Range 522/530 kHz - 1611/1710 kHz Preset Channel 40 Digital Tuner (North American) SIRIUS (North American) 145 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
■ Audio Inputs Digital Analog Multichannel Inputs Optical: 3 (Rear), 1 (Front) Coaxial: 3 BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE, TV/CD, AUX, PHONO 7.1 ■ Audio Outputs Analog VCR/DVR, TAPE, ZONE 2 PRE OUT, ZONE 3 PRE OUT Analog Multichannel Pre Outputs 9 Subwoofer Pre Outputs 2 Speaker Outputs Main (L, R, C, SL/Z4L, SR/Z4R, SBL/Z3L, SBR/Z3R) + LW/Z2L/SW1, RW/Z2R/SW2 + Front High (L, R) Phones 1 (6.
Specifications (DTR-70.2) Amplifier Section Tuner Section Rated Output Power All channels: FM Tuning Frequency Range (North American) 87.5 MHz - 107.9 MHz (Australian) 87.5 MHz - 108.0 MHz, RDS AM Tuning Frequency Range 522/530 kHz - 1611/1710 kHz Preset Channel 40 Digital Tuner (North American) SIRIUS (North American) 140 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
■ Audio Inputs Digital Analog Multichannel Inputs Optical: 2 (Rear), 1 (Front) Coaxial: 3 BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE, TV/CD, AUX, PHONO 7.1 ■ Audio Outputs Analog VCR/DVR, TAPE, ZONE 2 PRE OUT, ZONE 3 PRE OUT Analog Multichannel Pre Outputs 9 Subwoofer Pre Outputs 2 Speaker Outputs Main (L, R, C, SL/Z4L, SR/Z4R, SBL/Z3L, SBR/Z3R) + LW/Z2L/SW1, RW/Z2R/SW2 + Front High (L, R) Phones 1 (6.
About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Using an RIHD-compatible TV, Player, or Recorder p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than p-compatible components cannot be guaranteed.
3 ■ How to connect and setup 1 Confirm the connecting and setting. 1. Connect the HDMI OUT MAIN jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable.
Firmware Update There are the following methods to update the firmware: via network and via USB storage. Please choose either one that suits your condition. Before you start, carefully read the update procedure. It will take about 60 minutes to update the firmware. ■ Update via network You need a wired Internet connection to update the firmware. ■ Update via USB storage (➔ 119) Please prepare a USB storage device such as a USB flash memory stick.
5 6 7 Select “Update” and press Enter. Updating will begin. As the updating progresses, the TV screen may disappear depending on the program updated. In this case, you can see the update progress on the front display of the AV receiver. The TV screen will reappear when you finish the update and turn on the AV receiver. Message “Complete!” appears on the front display of the AV receiver, indicating that the update has been completed. Using On/Standby on the front panel, turn off and on the AV receiver.
Updating the Firmware via USB 5 The AV receiver allows you to update firmware using a USB storage device. * In this procedure, on-screen display may vary depending on the model. 6 Note • Make sure your AV receiver and TV are turned on. • Never unplug or turn off the AV receiver during updating process. • Never plug or unplug an HDMI cable and a USB device during updating process. • Never unplug the USB mass storage device and the power cord during updating process.
Troubleshooting Case1: If “No Update” is displayed on the front display of the AV receiver, the firmware has already been updated. You do not need to do anything further. Case2: If an error occurs, “Error!! *-** No media” is displayed on the front display of the AV receiver. (Alpha-numeric characters on the front display are denoted by asterisks.) See the following table and take appropriate action. ■ Errors during update via USB Error Code Description *-10, *-20 USB storage device is not detected.
Video Resolution Chart The following tables show how video signals at different resolutions are output by the AV receiver.
Memo En 122
Memo En 123
Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 En Y1007-1 SN 29400442 (C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.
