Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
114
Advanced Setup—Continued
Resolution
*2
Through: Select this to pass video through the AV receiver at the same resolution
and with no conversion (default).
Auto: Select this to have the AV receiver automatically convert video at
resolutions not supported by your TV. When the “Monitor Out” is set to
“Analog”, this setting will be changed to “Through”.
480p (480/576p):
Select this for 480p or 576p output and video conversion as necessary.
720p: Select this for 720p output and video conversion as necessary.
1080i: Select this for 1080i output and video conversion as necessary.
1080p: Select this for 1080p output and video conversion as necessary. When
the “Monitor Out” is set to “Analog”, this setting will be changed to
“1080i”.
1080p/24: Select this for 1080p output at 24 frames per second and video
conversion as necessary. When the “Monitor Out” is set to “Analog”,
this setting will be changed to “1080i”.
You can specify the output resolution for the HDMI outputs and have the AV receiver upconvert the picture
resolution as necessary to match the resolution supported by your TV.
Available only when “Source” has been selected in the “Resolution” of the “Monitor Out” setting (page 50).
Brightness
*2
–50 to +50 (default: 0)
With this setting you can adjust the picture brightness. “–50” is the darkest. “+50” is the brightest.
Contrast
*2
–50 to +50 (default: 0)
With this setting you can adjust contrast. “–50” is the least. “+50” is the greatest.
Hue
*2
–20 to +20 (default: 0)
With this setting you can adjust the red/green balance. “–20” is the strongest green. “+20” is the strongest red.
Saturation
*2
–50 to +50 (default: 0)
With this setting you can adjust saturation. “–50” is the weakest color. “+50” is the strongest color.
Gamma
*2
–3 to +3 (default: 0)
Adjust the balance of color data signal R (red), G (green), and B (blue) of incoming picture.
Red Brightness
*2
–50 to +50 (default: 0)
With this setting you can adjust the picture red brightness. “–50” is the darkest. “+50” is the brightest.
Red Contrast
*2
–50 to +50 (default: 0)
With this setting you can adjust red contrast. “–50” is the least. “+50” is the greatest.
Green Brightness
*2
–50 to +50 (default: 0)
With this setting you can adjust the picture green brightness. “–50” is the darkest. “+50” is the brightest.
Green Contrast
*2
–50 to +50 (default: 0)
With this setting you can adjust green contrast. “–50” is the least. “+50” is the greatest.
Blue Brightness
*2
–50 to +50 (default: 0)
With this setting you can adjust the picture blue brightness. “–50” is the darkest. “+50” is the brightest.
Blue Contrast
*2
–50 to +50 (default: 0)
With this setting you can adjust blue contrast. “–50” is the least. “+50” is the greatest.
Note:
*2 When the “ISF Mode” setting is set to “Day” or “Night”, this setting cannot be selected.