Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
139
Multi Zone—Continued
There are two ways you can connect Zone 3 speakers:
1. Connect them directly to the AV receiver.
2. Connect them to an amp in Zone 3.
Connecting Your Zone 3 Speakers Directly
to the AV receiver
This setup allows 7.2-channel playback in your main
room and 2-channel stereo playback in Zone 3, with a
different source in each room. This is called Powered
Zone 3, as the Zone 3 speakers are powered by the AV
receiver.
Hookup
• Connect your Zone 3 speakers to the AV receiver’s
SURR BACK/ZONE 3 L/R speaker terminals.
Notes:
• With this setup, the Zone 3 volume is controlled by the
AV r e c e ive r .
• Powered Zone3 cannot be used if “Speakers
Type(Front)” is set to “Bi-Amp” or “BTL” (see
page 54).
Connecting Your Zone 3 Speakers to an
Amp in Zone 3
This setup allows 9.2-channel playback in your main lis-
tening room and 2-channel stereo playback in Zone 3,
with a different source in each room.
Hookup
• Use an RCA audio cable to connect the AV receiver’s
ZONE 3 PRE OUT L/R jacks to an analog audio input
on your Zone 3 amp.
• Use an RCA audio cable to connect the AV receiver’s
ZONE 3 PRE OUT SW jack to the line input on a
powered subwoofer in Zone 3.
• Connect your Zone 3 speakers to the speaker terminals
on your Zone 3 amp.
Note:
With the default settings, the Zone 3 volume must be set
on the Zone 3 amp. If your Zone 3 amp has no volume
control, set the “Zone3 Out” setting to “Variable” so that
you can set the Zone 3 volume on the AV receiver (see
page 142).
Connecting Zone 3
To use this setup, you must set the “Powered Zone3”
setting to “Act” (see page 141).
L R
Main room
Zone 3
TV
AV receiver
LR
LINE INPUT
R
L
IN
Main room
TV
Zone 3
AV receiver
Receiver/
integrated amp
Powered subwoofer