Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
30
Connecting the AV receiver—Continued
■ “Monitor Out” Setting Set to “Both”, “Both(Main)” or “Both(Sub)”
With the “Monitor Out” setting set to “Both”,
“Both(Main)” or “Both(Sub)” (see page 49),
video input signals flow through the AV receiver
as shown, with composite video, S-Video, and
component video sources all being upconverted
for both HDMI outputs. Use the “Both”,
“Both(Main)” or “Both(Sub)” setting if you
connect the AV receiver’s HDMI OUT MAIN
and HDMI OUT SUB to your TVs.
The composite video, S-Video, and component
video outputs pass through their respective input
signals as they are.
Both: Video signals are output from both HDMI
outputs at the resolution supported by both TVs.
You cannot select “Resolution” setting. The pic-
ture adjust setting will be that for “HDMI Main”.
Both (Main): Video signals are output from both
HDMI outputs but HDMI OUT MAIN will become a priority; depending on the resolution, video signals may not be
output from HDMI OUT SUB.
Both (Sub): Video signals are output from both HDMI outputs but HDMI OUT SUB will become a priority; depending
on the resolution, video signals may not be output from HDMI OUT MAIN.
Note:
The “Monitor Out” setting will be automatically switched to “Analog” (see page 49) if not connected to both outputs
when “Both” is selected or if not connected to a priority output when “Both(Main)” or “Both(Sub)” is selected.
■ “Monitor Out” Setting Set to “Analog”
With the “Monitor Out” setting set to “Analog”
(see page 49), video input signals flow through
the AV receiver as shown, with composite video
and S-Video sources being upconverted for the
component video output. Use this setting if you
connect the AV receiver’s COMPONENT
VIDEO MONITOR OUT to your TV.
Composite video is upconverted to S-Video and
S-Video is downconverted to composite video.
Note that these conversions only apply to the
MONITOR OUT V and S outputs, not the
VCR/DVR OUT V and S outputs.
The composite video, S-Video, and component
video outputs pass through their respective input
signals as they are.
This signal flow also applies when the “Resolu-
tion” setting is set to “Through” (see page 49).
Video Signal Flow and the Resolution Setting
When the “Monitor Out” setting is set to “Ana-
log” (see page 49), if the “Resolution” setting is
set to anything other than “Through” (see
page 49), the video signal flow will be as shown
here, with composite video and S-Video sources
being upconverted for the component video out-
put.
The composite video, S-Video, and component
video outputs pass through their respective ana-
log input signals as they are. HDMI input signals
are not output.
IN
MONITOR OUT
DVD/BD player, etc.
AV receiver
TV, projector, etc.
Composite
Composite
S-Video
S-Video
Component
Component
Video Signal Flow Chart
HDMI
HDMI
IN
MONITOR OUT
DVD/BD player, etc.
AV receiver
TV, projector, etc.
Composite
Composite
S-Video
S-Video
Component
Component
Video Signal Flow Chart
HDMI
HDMI
IN
MONITOR OUT
DVD/BD player, etc.
AV receiver
TV, projector, etc.
Composite
Composite
S-Video
S-Video
Component
Component
Video Signal Flow Chart
HDMI
HDMI