Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
45
Turning On the AV receiver
On/Standby
Standby
On
Receiver
Standby indicator
Turning On and Standby
On the AV receiver, press the [On/Standby] button.
On the remote controller, press the [Receiver] button, followed by the
[On] button.
The AV receiver comes on, the display lights up, and the Standby indicator goes off.
Pressing the remote controller’s [On] button again will turn on any components
connected via u.
To turn the AV receiver off, press the [On/Standby] button, or press the remote
controller’s [Standby] button. The AV receiver will enter Standby mode. To prevent any
loud surprises when you turn on the AV receiver, always turn down the volume before
you turn it off.
or
Remote
controller
AV receiver
Smooth Operation in a Few Easy Steps
To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the
very first time. These settings only need to be made once.
■ Did you connect your TV to an HDMI output or COMPONENT VIDEO MONITOR OUT?
If you did, “Monitor Setup” on page 46.
■ Run MultEQ XT Room Correction and Speaker Setup—this is essential!
See “Audyssey MultEQ
®
XT Room Correction and Speaker Setup” on page 58.
■ Have you connected a component to an HDMI input,
component video input, or digital audio input?
If you have, see “HDMI Input Setup” on page 51, “Component Video
Input Setup” on page 52, or “Digital Audio Input Setup” on page 53
respectively.
■ Have you connected an Integra/Onkyo MD recorder, CD
recorder, or RI Dock?
If you have, see “Changing the Input Display” on page 57.
HDMI
OUT IN
TV/TAPE
MD recorder, CD recorder,
RI Dock