Owner's Manual
Table Of Contents
- Important Safety Instructions
- Precautions
- Supplied Accessories
- Features
- Front & Rear Panels
- Remote Controller
- About Home Theater
- Connecting the AV receiver
- Connecting Your Speakers
- Bi-amping the Front Speakers
- Bridging the Front Speakers
- Connecting Passive Subwoofers
- Connecting Antenna
- About AV Connections
- Connecting Components with HDMI
- Connecting Both Audio & Video
- Which Connections Should I Use?
- Connecting a TV or Projector
- Connecting a DVD Player
- Connecting a VCR or DVD Recorder for Playback
- Connecting a VCR or DVD Recorder for Recording
- Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source
- Connecting a Game Console
- Connecting a Camcorder or Other Device
- Connecting a CD Player or Turntable
- Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
- Connecting a Power Amplifier
- Connecting an RI Dock
- Connecting a Universal Port Option Series
- Connecting Integra/Onkyo RI Components
- Connecting the Power Cord
- Turning On the AV receiver
- First Time Setup
- Monitor Setup
- Selecting the Language used for the onscreen setup menus
- Using the Onscreen Setup Menus
- Using the Display to change the settings
- Monitor Out Setup
- Video Input Setup
- Digital Audio Input Setup
- Analog Audio Input Setup
- Speaker Settings
- TV Format Setup (Australian models)
- FM/AM Frequency Step Setup
- Changing the Input Display
- Audyssey MultEQ(R) XT Room Correction and Speaker Setup
- Basic Operations
- Listening to the Radio
- Universal Port Option UP-A1 Dock for iPod
- Recording
- Using the Listening Modes
- Advanced Setup
- NET/USB
- Multi Zone
- Controlling Other Components
- Preprogrammed Remote Control Codes
- Looking up for Remote Control Code
- Entering Remote Control Codes
- Remote Control Codes for Integra/ Onkyo Components Connected via RI
- Resetting Remote Mode Buttons
- Resetting the Remote Controller
- Controlling a TV
- Controlling a DVD Player or DVD Recorder
- Controlling a VCR or PVR
- Controlling a Satellite Receiver or Cable Receiver
- Controlling a CD Player, CD Recorder or MD Recorder
- Controlling an RI Dock
- Controlling a Cassette Recorder
- Activities Setup
- Learning Commands
- Using Normal Macros
- Troubleshooting
- Specifications (DTR-70.1)
- Specifications (DTR-80.1)
- Video Resolution Chart
57
First Time Setup—Continued
Note:
This procedure can also be performed on the AV receiver
by using its [Setup] button, arrow buttons, and [Enter]
button.
If you connect an u-capable Onkyo MiniDisc
recorder, CD recorder, or RI Dock to the TV/TAPE IN/
OUT jacks, or connect an RI Dock to the GAME IN or
VCR/DVR IN jacks, for u to work properly, you must
change this setting.
This setting can only be changed on the AV receiver.
Notes:
• DOCK can be selected for the TV/Tape or Game or
VCR/DVR input selector, but not at the same time.
• Enter the appropriate remote control code before
using the AV receiver’s remote controller for the first
time (see page 150).
3
Use the Up and Down [q]/[w] but-
tons to select “3. Tuner”, and
then press [Enter].
The “Tuner” menu appears.
(North American models)
(Australian models)
4
Use the Left and Right [e]/[r]
buttons to select:
(North American models)
200kHz/10kHz:
Select if 200 kHz/10 kHz steps are
used in your area.
50kHz/9kHz:
Select if 50 kHz/9 kHz steps are
used in your area.
(Australian models)
10kHz: Select if 10 kHz steps are
used in your area.
9kHz: Select if 9 kHz steps are used
in your area.
5
Press the [Setup] button.
The setup menu closes.
Changing the Input Display
7–3. Tuner
FM/AM Frequency Step
SAT Radio Mode
200kHz/10kHz
None
AM Frequency Step 9kHz
7–3. Tuner
1
Press the [TV/Tape], [Game] or
[VCR/DVR] input selector button
so that “TV/TAPE”, “GAME” or
“VCR/DVR” appears on the dis-
play.
2
Press and hold down the [TV/
Tape], [Game] or [VCR/DVR]
input selector button (about 3
seconds) to change the setting.
Repeat this step to select MD, CDR, or
DOCK.
For the TV/Tape input selector, the
setting changes in this order:
For the Game input selector, the setting
changes in this order:
GAME
↔ DOCK
For the VCR/DVR input selector, the
setting changes in this order:
VCR/DVR
↔ DOCK
VCR/DVR TV/
Tape
Game
or
or
or
or
(3 seconds)
TV/TAPE → MD → CDR
DOCK
→
→