AV Receiver DTR-7.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water.
Thank you for purchasing an Integra AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.
Contents Introduction Important Safety Instructions ....................2 Precautions .................................................3 Supplied Accessories.................................4 Features .......................................................6 Before Using the AV receiver ....................7 Getting to Know the AV Receiver ..............8 Remote Controller.....................................12 Connection Connecting Your Speakers ......................17 Connecting Antenna .................
Features Amplifier • 7-channel amplifier • 105 watts per channel into 8 ohms, 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating) • Optimum Gain Volume Circuitry • WRAT (Wide Range Amplifier Technology) • Massive High Current Power Supply (H.C.P.S.
Before Using the AV receiver Installing the Batteries 1 To open the battery compartment, press the small hollow and slide open the cover. Using the Remote Controller To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below. Remote control sensor Standby indicator AV receiver 30˚ 2 3 Insert the three supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. Slide the cover shut.
Getting to Know the AV Receiver Front Panel 12 3 4 P Q R 5 6 7 8 9 JK L M N S T O U V For detailed information, see the pages in parentheses. A Standby/On button (37) Sets the AV receiver to On or Standby. B Standby indicator (37) Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller. C Zone 2 indicator (80) Lights up when Zone 2 is on. D Remote-control sensor (7) Receives control signals from the remote controller.
Getting to Know the AV Receiver—Continued T Input selector buttons (46) U Setup Mic (38) Select the following input sources: Multi CH, DVD, Video 1, Video 2, Video 3, Video 4, Tape, Tuner, CD, or Phono. The automatic speaker setup microphone connects here. V Video 4 Input (32, 60) The [Multi CH] button selects the multichannel DVD input. Used to connect a camcorder, game console, and so on. There are jacks for optical digital audio, S-Video, composite video, and analog audio.
Getting to Know the AV Receiver—Continued Rear Panel 6 Only on the North American model 12 O 3 4 789 J 5 PQR S T U V A OPTICAL DIGITAL These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD players and DVD players. The optical digital audio output is for connecting a digital recorder with an optical digital input, such as a CD recorder.
Getting to Know the AV Receiver—Continued O REMOTE CONTROL This (Remote Interactive) jack can be connected to the jack on another -capable Integra/Onkyo component, for remote and system control. Z AC OUTLETS These switched AC outlets can be used to supply power to other AV components. The type and number of outlets depends on the country in which you purchased your AV receiver.
Remote Controller About the Remote Controller Modes Including the AV receiver, the remote controller can be used to control up to nine different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the eight Remote Mode buttons. Receiver/Tape Mode Receiver/Tape mode is used to control the AV receiver. It can also be used to control an Onkyo cassette recorder connected via .
Remote Controller—Continued For detailed information, see the pages in parentheses. T Muting button (54) Mutes or unmutes the AV receiver. A Standby button (37) Sets the AV receiver to Standby. B On button (37) Turns on the AV receiver. C Input Selector buttons (46) Used to select the input sources. D Multi CH button (53) Selects the multichannel DVD input. E Dimmer button (54) Adjusts the display brightness. F Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons G H I J Used to select and adjust settings.
Remote Controller—Continued A Standby button DVD Mode Sets the DVD player to Standby. To set the remote controller to DVD mode, press the [DVD] Remote Mode button. B On button Turns on the DVD player. C Number buttons Used to enter title, chapter, and track numbers, and to enter times for locating specific points. D Top Menu button Selects a DVD’s top menu. E Arrow [ ]/[ ]/[ ]/[ ] and Enter buttons A B Used to navigate menus and select items. F Disc +/– button Selects discs on a DVD changer.
Remote Controller—Continued A Standby button CD, MD, and CDR Modes Sets the CD player or MD/CD recorder to Standby. To control an Integra/Onkyo CD player or an Onkyo CD/MD recorder made by another manufacturer, press the [CD] Remote Mode button to select the CD remote controller mode. To control an Onkyo MD recorder or CD recorder, press the [MD] or [CDR] Remote Mode button to select the MD or CDR remote controller mode.
Remote Controller—Continued A Standby button HDD Mode Turns off the HDD-compatible component. HDD mode is for controlling Onkyo’s next generation HDD-compatible components. As of 2006, it can be used with the Onkyo RI Dock (Remote Interactive Dock) and Apple iPod connected via . When Using the RI Dock: • Connect the RI Dock to the TAPE IN or VIDEO 3 IN jacks. • Set the RI Dock’s RI MODE switch to HDD. • Set the AV receiver’s input display to HDD (see page 44). • Refer to the RI Dock’s instruction manual.
Connecting Your Speakers Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring DTS and Dolby Digital. With analog and digital TV, you can enjoy Dolby Pro Logic IIx and Onkyo’s own DSP surround listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended).
Connecting Your Speakers—Continued Connecting a Powered Subwoofer Connecting Your Speakers Speaker Configuration For the best surround-sound experience, you should connect seven speakers and a powered subwoofer. The following table shows which channels you should use based on the number of speakers you have.
Connecting Your Speakers—Continued Speaker Connection Precautions Read the following before connecting your speakers: • You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more but less than 6, be sure to set the minimum speaker impedance to 4 ohms (see page 44). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.
Connecting Antenna This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. AM antenna push terminals FM antenna jack Connecting the Indoor FM Antenna The supplied indoor FM antenna is for indoor use only. 1 Attach the FM antenna, as shown.
Connecting Antenna—Continued Connecting an Outdoor FM Antenna Connecting an Outdoor AM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
Connecting Your Components AV Connection Color Coding About AV Connections RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs. • Before making any AV connections, read the manuals supplied with your other AV components.
Connecting Your Components—Continued Connecting Audio and Video Signals to the AV Receiver By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver. : Signal Flow Video Video Audio Audio TV, projector, etc. DVD player, etc.
Connecting Your Components—Continued Connecting a TV or Projector Step 1: Video Connection Choose a video connection that matches your TV ( A , B , or C ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches your TV ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from your TV and listen in Zone 2. • To enjoy Dolby Digital and DTS, use connection b or c . (For Zone 2, use a and b , or a and c .
Connecting Your Components—Continued Connecting a DVD player Step 1: Video Connection Choose a video connection that matches your DVD player ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( a , b , or c ), and then make the connection. • With connection a , you can listen to and record audio from a DVD and listen in Zone 2.
Connecting Your Components—Continued Hooking Up the Multichannel DVD Input If your DVD player supports multichannel audio formats such as DVD-Audio or SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel DVD input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT L/R, CENTER, SURROUND L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player.
Connecting Your Components—Continued Connecting a VCR or DVD Recorder for Playback With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs. Hint! If you have two video recorders (e.g., a VCR and a DVD recorder), connect one recorder to the VIDEO 1 IN jacks, as shown here, and connect the other recorder to the VIDEO 2 IN jacks in the same way.
Connecting Your Components—Continued Connecting a VCR or DVD Recorder for Recording If you have two video recorders (e.g., a VCR and a DVD recorder), connect one recorder to the VIDEO 1 OUT jacks, as shown here, and connect the other recorder to the VIDEO 2 OUT jacks in the same way. Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( A or B ), and then make the connection.
Connecting Your Components—Continued Connecting a Satellite, Cable, Set-top box, or Other Video Source With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs. Hint! Step 1: Video Connection Choose a video connection that matches the video source ( A , B , or C ), and then make the connection. If you use connection A , you must connect the AV receiver to your TV with the same type of connection.
Connecting Your Components—Continued Connecting Components with HDMI About HDMI Designed to meet the demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
Connecting Your Components—Continued Making HDMI Connections Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV, projector, and so on. Step 2: Assign each HDMI IN to an input selector in the HDMI Video setup (see page 41). ■ Video Signal Flow Chart Digital video signals received at HDMI IN 1 and 2 are only output by the HDMI OUT and sent to your TV.
Connecting Your Components—Continued Connecting a Camcorder, Games Console, or Other Device Step 1: Video Connection Choose a video connection that matches the camcorder or console ( A or B ), and then make the connection. Step 2: Audio Connection Choose an audio connection that matches the camcorder or console ( a or b ), and then make the connection. B Video Input a b Input Input Digital S Video L Audio R Input A OPTICAL OUT S VIDEO OUT L AUDIO R OUT VIDEO OUT Camcorder, games console, etc.
Connecting Your Components—Continued Connecting a CD Player Step 1: Choose a connection that matches your CD player ( a , b , or c ), and then make the connection. b c COAXIAL IN 2 OPTICAL IN 3 a IN L R CD Connect one or the other L COAXIAL OUT OPTICAL OUT R AUDIO OUT CD player • With connection a , you can listen to and record audio from the CD player and listen in Zone 2. • To connect the CD player digitally, use connection b or c . (For Zone 2, use a and b , or a and c .
Connecting Your Components—Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches the recorder ( a , b , c , or d ), and then make the connection. b a IN COAXIAL IN 2 L R c TAPE OPTICAL a IN 4 L d OPTICAL R TAPE Connect one or the other L COAXIAL OUT OPTICAL OUT OPTICAL IN R AUDIO IN L R AUDIO OUT Cassette, CDR, MD, etc. • With connection a , you can play and record and listen in Zone 2.
Connecting Your Components—Continued Connecting an HDD-compatible Component As of this printing, the Onkyo Remote Interactive Dock is the only HDD-compatible component available. ■ For HDD-compatible components that support video Connect your HDD-compatible component’s analog audio output jacks and video output jack to the AV receiver’s VIDEO 3 IN L/R jacks and VIDEO 3 IN (V or S) jack. (The hookup example below shows how to connect the DS-A1.
Connecting Your Components—Continued Connecting Components Step 1: Make sure that each Integra/Onkyo component is connected to the AV receiver with an analog audio cable (RCA). Step 2: Make the connection. Step 3: If you’re using an MD, CDR, or HDD component, change the Input Display (see page 44).
Turning On the AV Receiver Standby/On Standby indicator Standby On Receiver Turning On and Standby Remote controller AV receiver or Press the [Standby/On] button. Alternatively, press the remote controller’s [Receiver] button, followed by the [On] button. The AV receiver comes on, the display lights up, and the Standby indicator goes off. Pressing the remote controller’s [On] button again will turn on any components connected via .
First Time Setup This section explains the settings that you need to make before using the AV receiver for the very first time. Automatic Speaker Setup With the supplied speaker setup microphone, the Automatic Speaker Setup function can measure the test tone output by each speaker and automatically determine the number of speakers connected, the crossover frequency, the distance from each speaker to the listening position, and so on. Before using this function, connect and position all of your speakers.
First Time Setup—Continued 3 Press [Enter]. The automatic speaker setup starts. The test tone is output by each speaker in turn. The microphone picks up the sound and feeds it back to the AV receiver, where it’s used to calculate the optimum speaker settings. The whole process takes about 2 minutes. 5 Disconnect the speaker setup microphone. Auto Speaker Setup ======================= Please,unplug Setup Mic. Auto Speaker Setup ======================== Do not unplug Setup Mic. Please, keep quiet.
First Time Setup—Continued ■ Checking the Results If you selected “Check the Results” in step 4 on the previous page, the following menu appears and you can check the results of the automatic speaker setup. Auto Speaker Setup ======================== 1.Warning 2.Speaker Config 3.Speaker Distance 4.Speaker Level Adjust 5.Equalizer Settings When you’ve finished checking, press the [Return] button to return to the menu in step 4.
First Time Setup—Continued HDMI Video Setup 1 Press the [Receiver] button, followed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “0.HDMI Video,” and then press [Enter]. The HDMI Video menu appears. 0.HDMI Video -----------------------a.DVD :--b.VIDEO1 :--c.VIDEO2 :--d.VIDEO3 :--e.
First Time Setup—Continued Component Video Setup 1 Press the [Receiver] button, followed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “1. Component Video,” and then press [Enter]. The Component Video menu appears. 1.Component Video -----------------------a.DVD :IN1 b.VIDEO1 :--c.VIDEO2 :--d.VIDEO3 :--e.
First Time Setup—Continued Digital Audio Input Setup 1 Press the [Receiver] button, followed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “2. Digital Input,” and then press [Enter]. The Digital Input menu appears. 2.Digital Input -----------------------a.DVD :Coax1 b.VIDEO1 :Opt1 c.VIDEO2 :----d.VIDEO3 :Opt2 e.VIDEO4 :Front f.TAPE :----g.CD :Opt3 h.
First Time Setup—Continued Changing the Input Display If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or next generation HDD-compatible component, such as the Remote Interactive Dock, to the TAPE IN/OUT or VIDEO 3 IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 1, 2 1 Minimum Speaker Impedance If you change this setting, you must run the automatic speaker setup again (see page 38).
First Time Setup—Continued TV Format Setup (not North American models) You must specify the TV system used in your area. 1 2 Press the [Receiver] button, followed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ ]/[ ] buttons to select “8. Hardware Setup,” and then press [Enter]. The Hardware Setup menu appears. AM Frequency Step Setup (on some models) You must specify the AM frequency step used in your area.
Playing Your AV Components Basic AV Receiver Operation 3 1 1 1 3 1 Remote controller AV receiver Use the AV receiver’s input selector buttons to select the input source. To select the input source with the remote controller, press the [Receiver] Remote Mode button, and then use the Input Selector buttons. On the remote controller, the [V1], [V2], [V3], and [V4] buttons select the VIDEO 1, VIDEO 2, VIDEO 3, and VIDEO 4 input sources respectively. 2 Start playback on the source component.
Listening to the Radio ■ Manual Tuning Mode Listening to AM/FM Stations Tuning Mode Tuning 1 Press the [Tuning Mode] button so that the AUTO indicator disappears from the display. 2 Press and hold the Tuning Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. Tuner With the built-in tuner, you can enjoy AM and FM radio stations, and store your favorite stations as presets for easy selection.
Listening to the Radio—Continued Listening to XM Satellite Radio® (North American Models Only) 1 Important XM Radio Information XM Satellite Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk and entertainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
Listening to the Radio—Continued Connecting the XM Mini-Tuner and Home Dock To receive XM Satellite Radio, you need an XM MiniTuner and Home Dock, which includes a home antenna. These are sold separately. For connection information, refer to the instruction manual supplied with the XM Mini-Tuner and Home Dock. XM antenna jack Signing Up for XM Satellite Radio Once you have installed the XM Mini-Tuner and Home Dock, you are ready to subscribe to XM Satellite Radio.
Listening to the Radio—Continued Display / Receiver Enter Display Tuner Selecting XM Radio Channels There are two ways to select XM radio channels: • Channel Search mode: select any channel. • Category Search mode: select channels by category. Note: You can’t select Channel Search or Category Search mode, while the Tuning Arrow indicators are flashing, as tuning is in progress.
Listening to the Radio—Continued Displaying XM Radio Information Positioning the XM Antenna Press the [Display] button repeatedly to cycle through the available information. You can check the signal strength of the XM Radio signal and adjust the position of the XM antenna accordingly. Channel name The following information is displayed: 1. Channel name 2. Channel number & Preset number 3. Category name (CAT) 4. Artist name (NAME) 5. Song title (TITL) 6.
Listening to the Radio—Continued Presetting AM, FM, and XM Stations 2, 4 Selecting Presets 1 3 You can store a combination of up to 40 of your favorite AM, FM, and XM radio stations. 1 Tune into the AM, FM, or XM station you want to store as a preset. 2 Press the [Memory] button. The MEMORY indicator appears and the preset number flashes. 1 1 52 3 While the MEMORY indicator is displayed (about 8 seconds), use the Preset [ ]/[ ] buttons to select a preset from 1 through 40.
Using the Multichannel DVD Input Multichannel DVD Input Settings 1 While the DVD input is selected, press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “4. Input Setup,” and then press [Enter]. Multi CH Receiver Use the Up and Down [ ]/[ ] buttons to select “2. MULTICH,” and then press [Enter]. The MULTICH menu appears. Enter Setup 4-2.MULTICH -----------DVD---------3.XM Antenna Aiming a.
Common Functions This section explains functions that can be used with any input source. Adjusting Speaker Levels You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to Standby. 1 Press [Receiver] first Dimmer Sleep Display Muting CH Sel Level – + Use the remote controller’s [CH Sel] button to select each speaker, and use the [Level–] and [Level+] buttons to adjust the volume.
Common Functions—Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. Press the remote controller’s [Sleep] button repeatedly to select the required sleep time. You can set the sleep time from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set, as shown.
Using the Listening Modes Selecting the Listening Modes Selecting with the Remote Controller For a description of each listening mode, see “About the Listening Modes” on page 58. • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). • Listening mode availability depends on the format of the current input signal.
Using the Listening Modes—Continued The following table shows which listening modes can be used with each input signal format. Source format 3/2.1 2/2.1 CD, TV, radio, cassette, etc. Listening mode DTS/DTS 96/24*2 Dolby Digital Analog, PCM*1 2/0 1/0, 1+1 Other 3/2.1 2/2.1 DVD, DTV, etc. DTS-ES 2/0 Discrete Matrix DVD, CD, etc.
Using the Listening Modes—Continued About the Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidelity reproduction. All of the source’s audio channels are output as they are. Stereo Sound is output by the front left and right speakers.
Using the Listening Modes—Continued THX Onkyo Original DSP Modes Founded by George Lucas, THX develops stringent standards that ensure movies are reproduced in movie theaters and home theaters just as the director intended. Mono Movie • THX Cinema This mode is for watching movies, which are typically recorded and edited on the assumption that they will be played in a sizable place like a movie theater.
Recording This section explains how to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources connected to the multichannel DVD input cannot be recorded. • Various restrictions apply to digital recording. Refer to the manuals supplied with your digital recording equipment for more details.
Onscreen Setup Menus About the Onscreen Setup Menus The onscreen setup menus are displayed on the connected TV (not via the HDMI OUT) and provide a convenient way to change the AV receiver’s settings, which are arranged into two groups: First Time Setup and Advanced Setup. To get your system up and running, you must complete the First Time Setup settings. The Advanced Setup settings are more detailed and allow you to tailor the AV receiver to suit your requirements.
Adjusting the Listening Modes Audio Adjust Menu The Audio Adjust menu has various settings for adjusting the sound and listening modes. 1 Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “6. Audio Adjust,” and then press [Enter]. The Audio Adjust menu appears. Receiver Enter 6.Audio Adjust -----------------------1.Tone Control 2.PL x/Neo:6 3.Dolby Digital 4.LFE Level 5.
Adjusting the Listening Modes—Continued Tone Control Settings PL IIx and Neo:6 Settings You can adjust the bass and treble for the front speakers. The tone control circuits are bypassed in the Direct listening mode. PL IIx Music (2 ch only) ■ Bass You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps. ■ Treble You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps.
Adjusting the Listening Modes—Continued Dolby Digital Settings Mono/Multiplex Settings ■ Dolby EX This setting determines how Dolby Digital EX signals are handled. This setting is unavailable if no surround back speakers are connected or the ZONE 2 SPEAKERS terminals are being used (page 78). Auto: Dolby Digital EX can be selected from among the Dolby listening modes, and THX Surround EX can be selected from among the THX listening modes.
Adjusting the Listening Modes—Continued Default Listening Modes 4 Use the Up and Down [ ]/[ ] buttons to select a signal format, and then use the Left and Right [ ]/[ ] buttons to select a listening mode. Only listening modes compatible with each signal format can be selected. The signal formats are explained below. 5 When you’ve finished, press the [Setup] button. Setup closes. You can specify a default listening mode for each signal format supported by each input selector.
Advanced Setup Speaker Setup 2 Use the Up and Down [ ]/[ ] buttons to select “3. Speaker Setup,” and then press [Enter]. The Speaker Setup menu appears. 3 Use the Up and Down [ ]/[ ] buttons to select “Speaker Configuration,” and then press [Enter]. The Speaker Config menu appears. This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the automatic speaker setup.
Advanced Setup—Continued 7 8 9 Use the Up and Down [ ]/[ ] buttons to select “d. Surround,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency. If no surround left and right speakers are connected, select None. Note: • If the Front setting in step 5 is set to anything other than Full Band, Full Band cannot be selected here. Use the Up and Down [ ]/[ ] buttons to select “e. SurrBack,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency.
Advanced Setup—Continued Speaker Distance 4 Use the Up and Down [ ]/[ ] buttons to select “a. Unit,” and then use the Left and Right [ ]/[ ] buttons to select: feet: Select if you want to enter distances in feet. Can be set from 1 to 30 feet in 0.5-foot steps. meters: Select if you want to enter distances in meters. Can be set from 0.3 to 9 meters in 0.15-meter steps. 5 Use the Up and Down [ ]/[ ] buttons to select each speaker and then use the Left and Right [ ]/[ ] buttons to specify the distance.
Advanced Setup—Continued Speaker Level Calibration 3 These settings are set automatically by the Automatic Speaker Setup function (see page 38). With these settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listening position. Notes: • The speakers cannot be calibrated while the output of the AV receiver is muted or a pair of headphones is connected.
Advanced Setup—Continued THX Audio Setup 4 Use the Left and Right [ ]/[ ] buttons to specify the surround back speaker spacing: 0–1 ft (0–0.3 m) (Default): Select this if the speakers are between 0 and 1 foot (0–30 cm) apart. 1–4 ft (0.3–1.2 m): Select this if the speakers are between 1 and 4 feet (0.3–1.2 m) apart. >4 ft (>1.2 m): Select this if the speakers are more than 4 feet (1.2 m) apart. 5 Press the [Setup] button. The setup menu closes.
Advanced Setup—Continued Equalizer Settings 5 These settings are set automatically by the Automatic Speaker Setup function (see page 38). With these settings, you can adjust the tone of each speaker. The volume of each speaker can be set on page 69. 1 2 3 4 3-6.Equalizer Settings -----------------------a.Use Settings:Manual -----------------------b.Channel :Left -----------------------c. 80Hz : 0dB d. 250Hz : 0dB e. 800Hz : 0dB f.2.5kHz : 0dB g.
Advanced Setup—Continued Input Setup 5 This section explains items on the “Input Setup” menu. Character Edit With this setting, you can enter a custom name for each input source and AM/FM radio preset. When the input source or radio preset is selected, its name will appear on the display. 1 Press the [Receiver] REMOTE MODE button, followed by the [Setup] button. To name an AM or FM radio preset, select that preset first. 2 Use the Up and Down [ ]/[ ] buttons to select “4.
Advanced Setup—Continued Preferences 4 Use the Up and Down [ ]/[ ] buttons to select an option, and use the Left and Right [ ]/[ ] buttons to change it. The preferences are explained in the next column. 5 When you’ve finished, press the [Setup] button. Setup closes. This section explains items on the “Preference” menu. Receiver Enter Setup Note: • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button.
Advanced Setup—Continued ■ Power On Vol / Z2 Power On Vol With these preferences, you can specify the volume settings to be used in the main room and Zone 2 when the AV receiver is turned on. When the Volume Display preference is set to Absolute, the range of “Power On Vol” is 0 to 100 (“Z2 Power On Vol” is 0 to 82). When it’s set to Relative, the range of “Power On Vol” is –∞ dB, –81 dB to +18 dB (“Z2 Power On Vol” is –∞ dB, –81 dB to 0 dB).
Advanced Setup—Continued Remote IDs 3 Use the Up and Down [ ]/[ ] buttons to select “Remote ID,” and use the Left and Right [ ]/[ ] buttons to select ID 1, 2, or 3. Remote indicator TV INPUT 8.Hardware Setup -----------------------a.PoweredZone2:NotAct b.Zone2 Out :Fixed c.TV Format :Auto d.AM Freq. Step: 9kHz e.Remote ID :1 Number buttons Receiver 4 Press the [Setup] button. Setup closes.
Advanced Setup—Continued Digital Input Signal Formats 3 Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS: • If the beginnings of tracks from a PCM source are cut off, try the PCM setting. • If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. 2-1.Digital Format -----------------------a.DVD :Auto b.
Advanced Setup—Continued Correcting Sound and Picture Sync When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. You can set it from 0 to 250 milliseconds (ms) in 1 millisecond steps. Input Selector Receiver 1 Press the [Receiver] Remote Mode button. 2 Press and hold, for more than 4 seconds, the input selector button for the input source that you want to correct.
Zone 2 Using Only Speakers in Zone 2 Connecting Zone 2 With the Zone 2 function, you can enjoy one input source in the main room and a different input source in another room. There are two ways to hook up your Zone 2 speakers: 1) Use another amp (receiver, integrated amp, or power amp) in Zone 2 and connect your Zone 2 speakers to it. 2) Connect your Zone 2 speakers to this AV receiver. With this hookup, you can enjoy 5.1-channel playback in the main room and a different stereo source in Zone 2.
Zone 2—Continued Powered Zone 2 Setting If you’ve connected your Zone 2 speakers to this AV receiver, as explained in “Using Only Speakers in Zone 2” on page 78, you must set the Powered Zone 2 setting to Act (Activated) as explained here. 1 2 3 Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ ]/[ ] buttons to select “8. Hardware Setup,” and then press [Enter]. The Hardware Setup menu appears.
Zone 2—Continued Using Zone 2 Controlling Zone 2 with the Remote Controller This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2. Standby On Controlling Zone 2 from the AV Receiver Input Selector 1 2 Zone2 1 Level–, Level+ To turn on Zone 2 and select an input source, press the [Zone 2] button repeatedly. Alternatively, press the [Zone 2] button followed by an input selector button within 8 seconds.
Zone 2—Continued Adjusting the Volume for Zone 2 Adjusting the Tone and Balance for Zone 2 You can adjust the bass, treble, and balance for Zone 2. Zone 2 Level , 1 2 1 On the remote controller, press the [Zone 2] Remote Mode button, and then use the [Level–] and [Level+] buttons. AV receiver On the AV receiver, use the Zone 2 Level [ ]/[ ] buttons. The volume can be set to –∞ dB, –81 dB –80 dB through 0 dB in Relative display (Min.1 through 81, Max in Absolute display).
Zone 2—Continued Using the 12V Triggers in Zone 2 and the Main Room When the AV receiver’s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V trigger input on a connected component, you can specify whether or not a 12volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either. Hookup • Use a miniplug cable to connect the AV receiver’s 12 V TRIGGER OUT A, B, or C jack to the 12 V trigger input on the connected component.
Zone 2—Continued Using the Remote Controller in Zone 2 and Multiroom Control Kits To control the AV receiver with the remote controller while you’re in the Zone 2 room, you’ll need a commercially available multiroom remote control kit. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the AV receiver’s remote sensor, such as when it’s installed inside a cabinet.
Controlling Other Components You can control your other components, including those made by other manufacturers, with the remote controller. This section explains how to: • Enter the remote control code for a component that you want to control (e.g., DVD, TV, VCR). • Learn commands directly from another component’s remote controller (see page 87). • Program the Macro buttons to perform a sequence of up to eight actions (see page 88).
Controlling Other Components—Continued Remote Control Codes for Integra/Onkyo Components Connected via Integra/Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. 1 Make sure the Integra/Onkyo component is connected with an cable and an analog audio cable (RCA). See page 36 for details.
Controlling Other Components—Continued To control another component, point the remote controller at it and use the buttons explained below. (You must select the appropriate remote control mode first.) With some AV components, certain buttons may not work as expected, and some may not work at all.
Controlling Other Components—Continued 3 VD D PO D C PE TA C IS D D C -1 VID EO IM D P EE SL ER W CH TI- T UL PU M IN O Remote indicator RE SUOD M About 2 to 6 inches (5–15 cm) O N R O T TO H SE C P ER E LE R N PR SE E TU T UN PU T IN P U PE O R TA G VD D -2 EO VID C H SE L E EV ST E TEON T L M U TIN G VO LU M E R The AV receiver’s remote controller can receive and learn commands from other remote controllers.
Controlling Other Components—Continued Using Macros 1 You can program the remote controller’s Macro buttons to perform a sequence of actions. Example: To play a CD, you typically need to perform the following actions: 1. Press the [Receiver] Remote Mode button to select the Receiver remote controller mode. 2. Press the [On] button to turn on the AV receiver. 3. Press the [CD] Input Selector button to select the CD input source. 4. Press the [CD] Remote Mode button to select the CD remote controller mode.
Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased. Power Can’t turn on the AV receiver • Make sure that the power cord is plugged into the wall outlet properly. • Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again. The AV receiver turns off as soon as it’s turned on • The amp protection circuit has been activated.
Troubleshooting—Continued The subwoofer produces no sound • When you play source material that contains no information in the LFE channel, the subwoofer produces no sound. • Make sure the speakers are configured correctly (pages 66, 67). The Zone 2 speakers produce no sound • The Zone 2 speakers only output sources that are connected to an analog input. Check to see if the source is connected to an analog input.
Troubleshooting—Continued Tuner Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t appear • Relocate your antenna. • Move the AV receiver away from your TV or computer. • Listen to the station in mono (page 47). • When listening to an AM station, operating the remote controller may cause noise. • Passing cars and airplanes can cause interference. • Concrete walls weaken radio signals. • If nothing improves the reception, install an outdoor antenna.
Troubleshooting—Continued The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction.
Specification Amplifier Section General Rated Power Output North American: 105 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) 135 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.
Memo 94
Memo 95
Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124 En I0609-2 SN 29344337A (C) Copyright 2006 ONKYO CORPORATION Japan. All rights reserved.
