Intel 7272LGANA User Guide Revision 1.
Revision History Revision History Revision Number Description Revision Date 1.0 Initial version of the document 17-Dec-2012 Rev. 1.
Revision History Contents 1 Introduction............................................................................................................................................ 6 2 Software Framework .......................................................................................................................... 8 2.1 2.1.1 Driver Installation ................................................................................................................................
Revision History Figures Figure 1. Location of the Prolific serial to USB driver, the Flash USB driver and the FTDI diver within the flash tool folder. ................................................................................ 8 Figure 2. Use the already installed driver. ............................................................................... 10 Figure 3. Install the driver again. ................................................................................................ 10 Figure 4.
Revision History Tables Table 1. Terminal Port Settings .................................................................................................... 22 Table 2. AT Commands trace box support. ................................ Error! Bookmark not defined. Table 3. Terminal Port Settings .................................................................................................... 25 Table 4. AT Commands to check ARM software version ....................................................
Revision History 1 Introduction This document provides a brief description of the NGFF Carrier Board development kit. Including: - Hardware interfaces with FIH board NGFF Carrier Board User Guide V2.0 Rev. 1.
Revision History Rev. 1.
Revision History 2 Software Framework 2.1 Driver Installation 2.1.1 General Considerations The two different test and debug configurations always require a Win PC where up to five different drivers must be installed accurately. This are: 1. the Intel High Speed Modem Driver (ecm200), 2. the Comneon High Speed Modem Driver, 3. the Prolific serial to USB driver (part of the flash tool folder), 4. the Flash USB driver (part of the flash tool folder) and 5. the FTDI diver. Figure 1.
Revision History http://wiki.imu.imc.local/XG716_LTE_CV_Setup_versions The latest drivers can be found here: \\musdsara001.imu.imc.local\SW_builds\xmm6360\tools Or if something is missing here: \\musdsara001.imu.imc.local\SW_builds\xmm7060\Release\Tools Which is similar to M:\Software\XMM7060_tools at IMC DRS Flash Tool : \\musdsara001.imu.imc.local\SW_builds\xmm6360\tools\flashtool Socmondll : \\musdsara001.imu.imc.local\SW_builds\xmm7060\Release\Tools\Socmondll\socmondll_1 00.150.001.dll 2.1.
Revision History Figure 2. Use the already installed driver. Figure 3. Install the driver again. Rev. 1.
Revision History Figure 4. The network modem and four COM ports are now appearing at the device manager. • Now open the network manager and configure the network settings of the modem. Rev. 1.
Revision History Figure 5. Open the network connections dialog. Win XP : Start:Settings:NetworkConnectios. A new network device did pop up. It is not yet connected. Figure 6. On Win7: Select “Start:Control Panel:Network and Sharing Center” followed by “Change adapter settings”. Figure 7. Open the properties dialog of the new network device (right click). Rev. 1.
Revision History 2.1.2.1 Client offset configuration. This must be done before the IP settings. If the order is flipped the IP settings get lost. Figure 8. Select the configuration dialog. Rev. 1.
Revision History Figure 9. Set the client offset to 1 and press “OK”. Figure 10. Press “OK” to save these settings. Otherwise these settings get lost. Rev. 1.
Revision History 2.1.2.2 Static IP Address Configuration • The given example IP number at Figure 12 is for a simplified test and debug setup, see Error! Reference source not found., where the octave or java client runs on the Win PC that also carries all necessary Win drivers and is connected to the DUT. The ecm200 driver runs in a subnet that is only visible from this PC. • The complete setup, see Error! Reference source not found.
Revision History Figure 11. Open the Internet Protocol TCP/IP settings. Rev. 1.
Revision History Figure 12. Set the static Network IP and press OK. Figure 13. To close the properties dialog and save the settings press “OK”. Rev. 1.
Revision History Figure 14. Congratulations. Your ecm200 driver and its IP connection are now properly configured. • 2.1.3 If desired it is now also possible to rename the network device from “Wireless Connection2” to something more convenient e.g. ecm200 + IP address. Comneon High Speed Modem Driver • Take the recommended driver, • \\musdsara001.imu.imc.local\SW_builds\xmm6360\tools\usb_drive rs See also SMS02534274: - Please use 3.46 version and not WMC_comneon2_3.55.0, see Subsec. 2.1.
Revision History Figure 15. Use the already installed driver. Figure 16. Install the driver. Rev. 1.
Revision History Figure 17. Comneon suspend and six COM ports are now appearing at the device manager. • 2.1.4 Congratulations, your driver installation has finished successfully. Flash USB driver and FTDI Driver These drivers are mandatory to flash new ARM software and LTE firmware images at the modem board. Take the recommended drivers, see Subsec. 2.1.1, (flash tool subfolder) and follow the instructions from the installation wizards. Note: 2.1.
Revision History Figure 18. USIF1 Device Manager Prolific USB-to-Serial COM Port 2.2 LTE debug UART configuration After the preliminary setting, run any AT terminal application (e.g. HyperTerminal) on your PC’s communication port, with the following settings. Rev. 1.
Revision History Table 1. Terminal Port Settings Data rate 115200 bps Data Bits 8 Parity N Stop Bits 1 Flow Control HW • on UNIX xterm use this with uucp: %docing station serial port, uucp chown uucp /dev/ttyUSB0 cu -l /dev/ttyUSB0 -s 115200 • If putty http://www.putty.org is used this looks like this: Figure 19. Putty configuration. Rev. 1.
Revision History 2.3 System Trace Box 2.3.1 Setup and Configuration 2.3.1.1 Entering AT Commands The AT commands mentioned below must be sent to the COM port that corresponds to the • Intel Mobile (USB3) COM port in case the ecm 200 driver is used or • to the COM port that corresponds to the Comneon High Speed Modem, see Error! Reference source not found.. The COM port that corresponds to the USIF-1 USB port, see Error! Reference source not found. may also work.
Revision History d. make sure your SIM is not waiting for entering a PIN: at+cpin? If it is, send the PIN at at+cpin= e. make sure, the 3G protocol stack is sending traces: at+cops=0; (this command triggers the phone to (re-)register to the network) 2.3.2 Connecting the UE 6. Connect the UE to the PC as described in section Error! Reference source not found.. 7. Find the com-port in which UE is connected using comtest tool. Run the command comtest –l. It will list the ports.
Revision History Table 3. Terminal Port Settings Data rate 115200 bps Data Bits 8 Parity N Stop Bits 1 Flow Control HW AT Command to check ARM Software version Table 4. AT Commands to check ARM software version Command sent by DTE Response of DCE Description at+xgendata The device will reply with the running ARM software version Register on the network (GSM/UMTS) Table 5.
Revision History Outgoing Voice Call Table 7. AT Commands for an Outgoing Call Command sent by DTE DCE Response Description AT OK AT+CLIP=1 Activation of Caller line ID presentation OK ATD+862161019000; Outgoing voice call OK Voice call is accept from network ATH Hang up OK SMS Management Table 8. AT Commands for SMS Management Command sent by DTE DCE Response Description AT+CMGF=1 OK Set the text mode as the format that will be used.
Revision History Rev. 1.
Revision History 3 Test Cases 3.1 Protocol Test (CMW500) Figure 20. CMW 500 In general it needs to be checked that CMW500 setup are identically to the reference. The components to be checked are : 3.1.1 • The test scenario configurations (xml files) and • The firmware versions for the tester hardware itself. CWM 500 Firmware The firmware version can be checked and maintained in the R&S Version Manager.
Revision History The R&S Version Manager can be opened via the START menu: Once opened there are two ways to verify similarity of firmware versions: by hand via stepping through the license options or by exporting the firmware (software status). The picture shows the version manager with the stepping through each firmware license: The next picture shows the menu from which the status export can be called: After this a pop-up window appears with three possible choices.
Revision History The directory “msg” is part of the CDK delivery and contains several xml files. It has to be noted that the xml version of the xml files needs to be compliant to the installed tester firmware. Otherwise strange errors occur during test case execution! http://www2.rohdeschwarz.com/en/products/test_and_measurement/mobile_radio/CMW500-|Demo-|-48-|-5420.html 3.1.3 AT Commands Network attach in CallBox Mode, LTE band 7. at+xact=6,2,1,107 at+cgdcont=1,"IP",”www.rohde-schwarz.
Revision History Make sure your Router is connected to the "LAN DAU" ETH port at the back side of the CMW. Open the SETUP menu on the right side. Open the DAU configuration via menu: Data Appl. Control Go to config Configure the DAU to use DHCP As shown on the screenshot, choose last check mark DHCPv4 from LAN (LAN DAU) for IPv4 Address Configuration Close the CMW BaseSW (ALT + F4) and start it again afterwards by a DoubleClick on the desktop link "CMW 1.
Revision History Manual DNS settings On the LTE host which connects to the internet, the DNS server has to be configured manually, because the DAU does not yet support automatic DNS provisioning (ask your IT). In case of a LTE notebook adapter, the DNS server will be configured on the IP properties pane: Rev. 1.
Revision History 4 Regulatory Notice Manual Information to the End User: The OEM integrator has to be aware the end user manual shall include all required regulatory information/warning as show in this manual. USA—FCC and FAA The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment.
Revision History • A heating test shall be considered in the end-use product for meeting the requirement of UL/EN/IEC 60950-1 2nd edition. Antenna Use • To comply with FCC RF exposure limits, it is recommended that for the wireless adapter installed in a host computer , the low gain integrated antennas for this device should be located at a minimum separation distance from the body of all persons as specified according to the FCC modular grant conditions.
Revision History • Using the wireless adapter on board airplanes, or • Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the adapter before you turn it on.
Revision History • This wireless adapter is intended for OEM integrators only. • This wireless adapter cannot be co-located with any other transmitter unless approved by the FCC based upon FCC Knowledge Database publication number 616217 D03 (Supplement) when there are multiple radios installed in a host device, RF exposure transmitting assessment shall be performed to determine the necessary application and test requirements.
Revision History Simultaneous Transmission of Intel® Wireless Adapters with Other Integrated or Plug-In Transmitters Based upon FCC Knowledge Database publication 616217 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?id=33240&switch=P number , when there are multiple transmitting devices installed in a host device, an RF exposure transmitting assessment shall be performed to determine the necessary application and test requirements.
Revision History To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer's OEM Regulatory Guidance document. Canada—Industry Canada (IC) This device complies with Industry Canada licence-exempt RSS standard(s).
Revision History 5 Abbreviations / Terminology A A-GPS Assisted-GPS (Global Positioning System) AP Application Processor B BB Baseband C CMOS Complementary Metal Oxide Semiconductor CN Comneon D DigRF v4 Digital RF interface v4 (rmainly used for 4G) DigRF 3.
Revision History M MIPI Mobile Industry Processor Interface MMC(I) Multimedia Card (Interface) MPU Microprocessor unit O P PA Power Amplifier PCL Port Control Logic PMU Power Management unit PTI Parallel Trace Interface S SD-Card Secure Digital Card SMT pin header Surface Mount Technology pin header SPI Serial Peripheral interface S4G SMARTi™ 4G ST MIPI System Trace MIPI STT System Trace Tool SVB System verification board SW Software T TAP Test Access Port TCU Test Control U
Revision History Appendix A Definitions/Explanations Eval Board special processor socket board for X-GOLD™ 716 component verification Lauterbach Supplier of Debug and Trace environment for X-GOLD™ 716 (e.g. JTAG, ETM7/11, ST MIPI) Modem board Main part of XMM™ 7160 platform hardware (see Error! Reference source not found.) XMM™ 7160 Project name of Intel platform with key component X-GOLD™ 716 RF- Engine RF part of platform (RF-transceiver, Power amplifiers, LNA, Filter bank, antenna switch etc.
