Datasheet

ManualsBrandsIntel Manualscomputer componentsBXM80530B866512

Mobile Intel

Pentium

III Processor in BGA2 and Micro-PGA2 Packages at 1 GHz,

900 MHz, 850 MHz, 800 MHz, 750 MHz, 700 MHz, Low-voltage 750 MHz, Low-voltage

700 MHz, Low-voltage 600 MHz, Ultra Low-voltage 600 MHz and Ultra Low-voltage 500 MHz

283653-002 Datasheet 29

Table 9A. Mobile Pentium III Processor DC Specifications

Symbol Parameter Min Typ Max Unit Notes

Transient V

for core logic

at 300 MHz & 0.975V

at 500 MHz, 600 MHz & 1.10V

at 600 MHz & 1.15V

at 550 MHz, 600 MHz, 650 MHz, 700 MHz, 750 MHz & 1.35V

at 700 MHz, 750 MHz, 800 MHz, 850 MHz & 1.60V

at 900 MHz, 1 GHz & 1.70V

0.95

1.02

1.07

1.25

1.485

1.62

0.975

1.10

1.15

1.35

1.60

1.70

1.0

1.18

1.23

1.45

1.715

1.825

±25 mV

±80 mV

±100 mV

±115 mV

-80/+125 mV

Note 5,6

CC,DC

Static V

for core logic

at 300 MHz & 0.975V

at 500 MHz, 600 MHz & 1.10V

at 600 MHz & 1.15V

at 550 MHz, 600 MHz, 650 MHz, 700 MHz, 750 MHz & 1.35V

at 700 MHz, 750 MHz, 800 MHz, 850 MHz & 1.60V

at 900 MHz, 1 GHz & 1.70V

0.95

1.02

1.07

1.25

1.485

1.62

0.975

1.10

1.15

1.35

1.60

1.70

1.0

1.18

1.23

1.45

1.640

1.74

±25 mV

±80 mV

±100 mV

-115/+40 mV

-80/+40 mV,

Note 2,6

CCT

for System Bus Buffers, Transient tolerance 1.385 1.50 1.615 V ±115 mV,

Note 5,6

CCT,DC

for System Bus Buffers, Static tolerance 1.455 1.50 1.545 V ±3%, Note 2,6

/dt V

power supply current slew rate 1400

A/µs

Notes 3,4

NOTES:

1. Unless otherwise noted, all specifications in this table apply to all processor frequencies.

2. Static voltage regulation includes: DC output initial voltage set point adjust, output ripple and noise, output

load ranges specified in above, temperature, and warm up.

3. Based on simulations and averaged over the duration of any change in current. Use to compute the

maximum inductance and reaction time of the voltage regulator. This parameter is not tested.

4. Maximum values specified by design/characterization at nominal V

and V

CCT

5. V

CCx

must be within this range under all operating conditions, including maximum current transients. V

CCx

must return to within the static voltage specification, V

CCx,DC

, within 100 µs after a transient event.

6. Voltages are measured at the processor package pin for the Micro-PGA2 part and at the package ball on

the BGA2 part.

7. T

= 0°C to 100°C and Tj = 5°C to 100°C for Vcc = 1.15V

Table 9B. Mobile Pentium III Processor DC Specifications

Core Speed Vcc

(nominal)

Icc

(max)

Icc

(max)

Icc

(max)

Icc

(max)

Icc

DSLP

(max)

Unit

500 / 300 MHz

600 / 300 MHz

600 / 500 MHz

700 / 500 MHz

750 / 500 MHz

700 / 550 MHz

750 / 600 MHz

800 / 650 MHz

850 / 700 MHz

900 / 700 MHz

1GHz / 700 MHz

1.1 / 0.975V

1.15 / 0.975V

1.35 / 1.10V

1.60 / 1.35V

1.70 / 1.35V

7.90 / 4.72

9.14 / 4.72

11.20 / 7.90

12.80 / 7.90

13.49 / 7.90

14.60 / 10.30

15.60 / 11.20

16.60 / 12.00

17.60 / 12.80

19.30 / 12.80

21.10 / 12.80

2.50 / 2.50

1.50 / 1.30

1.60 / 1.30

1.70 / 1.50

2.70 / 1.50

2.20 / 1.70

3.50 / 2.70

3.91 / 2.70

1.30 / 1.20

1.40 / 1.20

1.50 / 1.30

2.40 / 1.30

1.90 / 1.50

3.00 / 2.40

3.46 / 2.40

1.10 / 1.10

1.30 / 1.10

1.20 / 1.10

2.10 / 1.10

1.60 / 1.20

2.50 / 2.10

3.00 / 2.50

NOTES:

1. I

CCT

is the current supply for the system bus buffers, including the on-die termination.

2. I

CCx,max

specifications are specified at V

CC, DC max

, V

CCT,max

, and 100°C and under maximum signal

loading conditions.

3. Battery Optimized mode current is based on design / characterization only. Not 100% tested.

4. Icc is current for V

at core frequency. Not 100% tested. Specified by design/characterization.

5. Icc

is current for V

CCT

. Not 100% tested. Specified by design/characterization.

6. Icc

is Stop Grant and Auto Halt current. Not 100% tested. Specified by design/characterization.

7. Icc

is Quick Start and Sleep current. Not 100% tested. Specified by design/characterization.