SubCompact Board GENE-8310 GENE-8310 ® Intel Celeron® M Processor Subcompact Board With LVDS, Ethernet, 6 Channel Audio & Mini PCI GENE-8310 Rev. A Manual 2nd Ed. Jan.
SubCompact Board GENE-8310 Copyright Notice This document is copyrighted, 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
SubCompact Board GENE-8310 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™ is a trademark of the Compact Flash Association. Intel®, Pentium® M, and Celeron® M are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. ITE is a trademark of Integrated Technology Express, Inc.
SubCompact Board GENE-8310 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 GENE-8310 CPU Card • 1 IDE Cable • 1 KB/Mouse Cable • 2 USB Cable • 1 Audio Cable • 1 COM Port Cable • 1 TV-out and S-terminal Cable • 1 DVI Cable • 1 Parallel Port Cable • 1 Jumper Cap • 1 Quick Installation Guide • 1 CD-ROM for manual (in PDF format) and drivers If any of these items should be missing or damaged, please contact your d
SubCompact Board GENE-8310 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Features .................................................................... 1-4 1.3 Specifications ............................................................ 1-5 Chapter 2 Quick Installation Guide 2.1 Safety Precautions .................................................... 2-2 2.2 Location of Connectors and Jumpers ....................... 2-3 2.
SubCompact Board GENE-8310 2.18 4P Power Connector (CN9) .................................... 2-16 2.19 TV-out Connector (CN10) ....................................... 2-17 2.20 DVI Connector (CN11) ............................................ 2-17 2.21 Audio Input/Output Connector (CN12) .................... 2-17 2.22 Ethernet 10/100 BaseT RJ-45 Phone Jack Connector (CN13) ............................................................................. 2-18 2.23 External 5VSB/PWRGD Connector (CN14).........
SubCompact Board GENE-8310 Appendix B I/O Information B.1 I/O Address Map ....................................................B-2 B.2 1st MB Memory Address Map ................................B-2 B.3 IRQ Mapping Chart ................................................B-3 B.4 DMA Channel Assignments...................................
SubCompact Board GENE-8310 Chapter 1 General Information Chapter 1 General Information 1- 1
SubCompact Board GENE-8310 1.1 Introduction The GENE-8310 is the third generation of fanless solutions that AAEON has released through their original design. It is more advanced than previous SubCompact Boards, with higher performance and lower power consumption. We believe the GENE-8310 will become one of the best choices for our customers who need a higher requirement in processor ability with excellent power consumption control.
SubCompact Board GENE-8310 Intel® platform. It has the best graphics capability among current 3.5” SubCompact Boards. In addition, the GENE-8310 supports CRT, LCD, DVI and TV-out which can meet your requirements. The result is you will never need to worry about the limitations of board size and power consumption using this SubCompact Board for sophisticated graphics output. Wide Expansion Capability Although the GENE-8310 measures only 5.
SubCompact Board GENE-8310 1.2 Features • Onboard Intel® Celeron® M or Mobile Intel® Celeron® Processor at 600MHz 0K L2 Cache Processor • 48-bit Dual Channels LVDS TFT LCD • 10/100Mbps Fast Ethernet • AC-97 3D Surround 5.1 Channel Audio • Supports Type II CompactFlash™ Memory • 2 COM / 4 USB2.
SubCompact Board GENE-8310 1.3 Specifications System • CPU: Onboard Mobile Intel® Celeron® Processor at 600MHz with 0K L2 Cache or Intel® Celeron® M Processor 1.3GHz Memory: 200-pin DDR SODIMM x 1, Max.
SubCompact Board GENE-8310 101.6mm) Gross Weight: 0.88lb (0.
SubCompact Board USB: GENE-8310 Two 5 x 2 Pin Headers Support 4 USB 2.
SubCompact Board GENE-8310 Chapter 2 Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product. Part No. 2007831011 Printed in Taiwan JAN.
SubCompact Board GENE-8310 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
SubCompact Board GENE-8310 2.2 Location of Connectors and Jumpers Component Side 6 11 CN9 5 15 CN19 CN17 CN16 CN8 CN18 CN11 12 11 7 8 CN10 9 10 1 2 CN13 JP2 CN15 MPCI1 CN12 JP5 CN6 CN7 CN14 CN5 CN3 CN4 CN2 CN1 JP1 NOTE: The Height of Cooling System Depends on Customer Cooling Device.
SubCompact Board Solder Side CFD1 DIMM1 Chapter 2 Quick Installation Guide 2-4 GENE-8310
SubCompact Board GENE-8310 2.3 Mechanical Drawing Component Side (14.15) 3.23 0.00 78.69 95.20 98.37 (7.88) (46.99) (22.23) 6 137.16 133.93 11 137.16 133.93 (1.60) 114.94 84.77 90.17 (6.45) 91.00 79.38 (77.47) 109.22 (103.51) 5 87.58 90.79 0.58 15 114.30 0.58 72.39 54.15 52.60 50.31 12 11 29.22 9 10 7 72.35 2 1 63.45 8 43.99 41.59 8.89 95.83 81.58 78.05 23.50 0.32 0.27 0.00 0.00 1.91 6.99 8.89 95.20 76.47 62.81 50.75 51.19 39.76 28.33 16.90 3.23 1.32 0.
SubCompact Board GENE-8310 3.23 0.00 95.20 98.37 Solder Side 8.89 8.89 0.00 0.00 0.58 72.39 109.22 Chapter 2 Quick Installation Guide 2-6 133.93 95.20 0.00 133.93 87.58 0.58 114.
SubCompact Board GENE-8310 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.
SubCompact Board GENE-8310 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Connectors Label Function CN1 USB 2.0 Port 1 Connector CN2 USB 2.
SubCompact Board GENE-8310 CN17 Mini-DIN PS/2 Connector CN18 Serial Port COM 1 Connector CN19 CRT Display Connector VBAT2 External Battery MPCI1 Mini PCI Slot CFD1 Compact Flash Disk Slot Chapter 2 Quick Installation Guide 2-9
SubCompact Board GENE-8310 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
SubCompact Board GENE-8310 2.7 Clear CMOS Selection (JP1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.8 LCD Voltage Selection (JP2) JP2 Function 1-2 +5V (Default) 2-3 +3.3V 2.9 COM2 RI/+5V Selection (JP5) JP5 Function 1-2 +5V 3-4 RI (Default) 2.10 USB2.
SubCompact Board GENE-8310 2.11 USB2.0 Port 2 Connector (CN2) Pin Signal Pin Signal 1 USBVDD2-3 2 USBGND 3 USBD2- 4 USBGND 5 USBD2+ 6 USBD3+ 7 USBGND 8 USBD3- 9 USBGND 10 USBVDD2-3 2.
SubCompact Board GENE-8310 29 PDDACK# 30 Ground 31 IRQ14 32 N/C 33 PDA1 34 P66DET 35 PDA0 36 PDA2 37 PDCS#1 38 PDCS#3 39 IDEACTP# 40 Ground 41 +5Volt. 42 +5Volt. 43 Ground 44 N/C 2.13 Digital IO Connector (CN4) Pin Name Pin Name 1 Port 1 2 Port 2 3 Port 3 4 Port 4 5 Port 5 6 Port 6 7 Port 7 8 Port 8 9 +5V 10 Ground DIO Address is 801H: BIOS Setting Connector Definition Address IT8712 GPIO Setting Port 1 CN4. pin 1 Bit 7 U35.
SubCompact Board GENE-8310 Port 7 CN4. pin 7 Bit 1 U35. pin 26 (GPIO21) Port 8 CN4. pin 8 Bit 0 U35. pin 27 (GPIO20) 2.14 Front Panel (CN5) Pin Signal 1-2 ATX Power-on Button 3-4 HDD Active LED 5-6 External Speaker 7-8 Power LED 9-10 System Reset Button 2.
SubCompact Board 9 Ground GENE-8310 10 N/C COM2/ RS-485 Mode Pin Signal Pin Signal 1 TXD- 2 N/C 3 TXD+ 4 N/C 5 N/C 6 N/C 7 N/C 8 N/C 9 Ground 10 N/C Note: COM mode, RS-232/422/485, selected by BIOS. 2.
SubCompact Board GENE-8310 2.17 Dual Channel LVDS Connector (CN8) Pin Signal Pin Signal 1 Back-Light Enable 2 Back-Light Control 3 LCD Volt. 4 Ground 5 TXLCLK# 6 TXLCLK 7 LCD Volt. 8 Ground 9 TXL0# 10 TXL0 11 TXL1# 12 TXL1 13 TXL2# 14 TXL2 15 TXL3# 16 TXL3 17 LVDS_DATA 18 LVDS_CLK 19 TXU0# 20 TXU0 21 TXU1# 22 TXU1 23 TXU2# 24 TXU2 25 TXU3# 26 TXU3 27 LCD Volt. 28 Ground 29 TXUCLK# 30 TXUCLK 2.
SubCompact Board GENE-8310 2.19 TV-Out Connector (CN10) Pin Signal Pin Signal 1 Y 2 CVBS 3 Ground 4 Ground 5 C 6 N/C 7 Ground 8 N/C 2.20 DVI Connector (CN11) Pin Signal Pin Signal 1 TD1 2 TD1# 3 Ground 4 Ground 5 TDC 6 TDC# 7 Ground 8 +5V 9 HPDET 10 +5V 11 TD2 12 TD2# 13 Ground 14 Ground 15 TD0 16 TD0# 17 N/C 18 N/C 19 DVI_DATA 20 DVI_CLK 2.
SubCompact Board GENE-8310 9 Audio Ground 10 CD_R 11 LINE_OUT L 12 LINE_OUT R 13 Audio Ground 14 Audio Ground 2.22 Ethernet 10/100Base-TX RJ-45 Phone Jack Connector (CN13) Pin Signal Pin Signal 1 TX+ 2 TX- 3 TCT 4 N/C 5 N/C 6 RCT 7 RX+ 8 RX- 9 LINK_LED 10 ACT_LED 11 SPD_LED 12 +3.3V 2.23 External 5VSB/PWRGD Connector (CN14) Pin Signal 1 N/C 2 Ground 3 N/C 4 Ground 5 PS_ON 6 +5V Stand-by 2.
SubCompact Board GENE-8310 3 Rx 4 Ground 5 Tx 6 N/C (CIR_Rx Option) 2.25 Fan Connector (CN16) Pin Signal 1 FAN Sense 2 +5V 3 Ground 2.26 Mini-DIN PS/2 Connector (CN17) Pin Signal Pin Signal 1 Keyboard Data 2 Mouse Data 3 Ground 4 Shield 5 +5V 6 Keyboard Clock 7 Shield 8 Mouse Clock 2.
SubCompact Board GENE-8310 2.28 CRT Display Connector (CN19) Pin Signal Pin Signal 1 CRT RED 9 5V 2 CRT_GREEN 10 VGA Ground 3 CRT_BLUE 11 N/C 4 N/C 12 CRT_SDA 5 VGA Ground 13 CRT_HSYNC 6 VGA Ground 14 CRT_VSYNC 7 VGA Ground 15 CRT_SCL 8 VGA Ground 2.29 External Battery (VBAT2) Pin Signal 1 VBAT (+3V) 2 Ground 2.30 Mini PCI Slot (MPCI1) Standard Specification. 2.
SubCompact Board GENE-8310 7 SDCS#1 32 SDCS#3 8 Ground 33 Ground 9 Ground 34 SDIOR# 10 Ground 35 SDIOW# 11 Ground 36 +5 Volt.
SubCompact Board GENE-8310 Chapter 3 Award BIOS Setup Chapter 3 Award BIOS Setup 3-1
SubCompact Board GENE-8310 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
SubCompact Board GENE-8310 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press immediately. This will allow you to enter Setup. Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.
SubCompact Board GENE-8310 Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify your settings for power management. (HDD power down, power on by ring, KB wake up, etc.) PnP/PCI Configurations This entry appears if your system supports PnP/PCI.
SubCompact Board GENE-8310 While AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. You can refer to the "AAEON BIOS Item Description.pdf" file in the CD for the meaning of each setting in this chapter.
SubCompact Board GENE-8310 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
SubCompact Board GENE-8310 The GENE-8310 comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Intel® INF Update for Windows 2000/XP Step 2 – Install Intel® Extreme Graphics 2 Driver Step 3 – Install Intel® LAN 82562ET Driver Step 4 – Install Realtek AC97 codec Driver USB 2.0 Drivers are available for download using Windows Update for both Windows XP and Windows 2000.
SubCompact Board GENE-8310 4.1 Installation: Insert the GENE-8310 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install Intel® INF Update for Windows 2000/XP 1. Click on the Intel® INF Update for Windows 2000/XP folder and then double click on the setup.exe 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically Step 2 – Install Intel Extreme Graphics 2 Driver 1.
SubCompact Board GENE-8310 Step 4 – Install Realtek AC97 codec Driver 1. Click on the Realtek AC97 codec Driver folder and then double click on the setup.exe 2. Follow the instructions that the window shows 3.
SubCompact Board GENE-8310 Appendix A Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1
SubCompact Board GENE-8310 A.1 Programming GENE-8310 utilizes ITE 8712 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description After the hardware reset or power-on reset, the ITE 8712 enters the normal mode with all logical devices disabled except KBC.
SubCompact Board GENE-8310 occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logic, it is necessary to perform four write opera-tions to the Special Address port (2EH). Two different enter keys are provided to select configuration ports (2Eh/2Fh) of the next step.
SubCompact Board GENE-8310 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
SubCompact Board GENE-8310 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Register (Index=72h, Default=00h) WatchDog Timer Time-out Value Register (Index=73h, Default=00h) Appendix A Programming the Watchdog Timer A-5
SubCompact Board GENE-8310 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call Superio_Set_Reg ;unit is second.
SubCompact Board GENE-8310 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter_Configuration_Mode ENDP Exit_Configuration_Mode PROC NEAR MOV AX,0202h CALL Write_Configuration_Data Appendix A Programming the Watchdog Timer A-7
SubCompact Board GENE-8310 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL Appendix A Programming the Watchdog Timer A-8
SubCompact Board GENE-8310 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push ax MOV DX,WORD PTR CS:[Cfg_Port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret Superio_Set_Reg endp.
SubCompact Board GENE-8310 Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not valid 0Ch: IRQ12 . .
SubCompact Board GENE-8310 Appendix B I/O Information Appendix B I/O Information B-1
SubCompact Board GENE-8310 B.
SubCompact Board GENE-8310 B.3 IRQ Mapping Chart IRQ0 System Timer IRQ1 Keyboard IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 Cascade to IRQ Controller COM2 COM1 Unused Unused Printer IRQ8 System CMOS / Real time clock IRQ9 Microsoft ACPI – Compliant system IRQ10 Unused IRQ11 Unused IRQ12 PS/2 mouse IRQ13 FPU IRQ14 Primary IDE IRQ15 Secondary IDE B.
