CV700A / CV702A 400MHz FSB / VGA / LAN / Sound 400MHz FSB . All-in-one Sound . 3 LAN SATA150 . ATA 33/66/100 . USB . IrDA . CF Multi- LAN Board NO.CV700A / CV702A Release date: OCT.26.
Contents CV700A / CV702A CHAPTER 1 GENERAL INFORMATION ........................................................................ 1 1-1 MAJOR FEATURE........................................................................................................ 2 1-2 SPECIFICATION .......................................................................................................... 3 1-3 HARDWARE NOTICE GUIDE .....................................................................................
-14 DC +5/+12V OUTPUT CONNECTOR....................................................................... 32 3-15 SERIAL ATA .............................................................................................................. 33 3-16 I 2 C BUS CONNECTOR ............................................................................................ 33 3-17 TV-OUT CONNECTOR ............................................................................................ 34 3-18 FRONT-PANEL ...................
2006 OCT . 26 .
Chapter-1 General lnformation The CV700A is a Light form factor All-In-One Multimedia control Board. The board design combines all necessary input and output effects interfaces, which makes itself an ideal all-in-one control board for Networking Application. The board is designed with 400 MHz internal bus clock rate architecture.
1-1 Major Feature 1. VIA Eden (V4) nano BGA2 500MHz CPU/ VIA C7 nano BGA2 1GHz CPU 2. VIA CN700 chipset (CN700 + VT8237R Plus) 3. One DDR2 400/533 DRAM unbuffered double-sided DIMMs up to 1GB 4. Dual channel master mode PCI support four IDE disk drives DMA 33/66/100 controller One Channle SATA 150 Connector 5. 400 MHz system clock support 6. Versatile storage device: * One 50-pin Compact Flash socket * One 40-pin DOM * One 2.5" HDD * One SATA HDD 7.
1-2 Specification 1.CPU: VIA Eden (V4) nano BGA2 500 MHZ CPU / VIA C7 (V4) nano BGA2 1GHz CPU 2. Cache Memory: Integrated full-speed 128KB L1/L2 cache 3.Chipset: VIA CN700 (North:CN700 ;South:VT8237R Plus) 4. Memory: One DIMM socket up to 1GB DDR2 400/533 DRAM 5. VGA: CN700 integrated graphic controller ; support 128-bit 2D/3D display up to 1600x1200, memory sharable up to 64MB 6. I/O Chipset: VIA VT1211IO 7.
1-3 Hardware Notice Guide 1. Before installing the power supply with this motherboard, please attach the 12V/DC ( 4 pin connector )of the adapter to motherboard first. After that, plug the adapter power to AC outlet. Always normally shut down the computer before you move the system unit or remove the power supply from the motherboard. Please unplug the 12V/DC ( 4 pin connector ) of the adapter from motherboard first. Then unplug the adapter from the AC outlet. Please refer to procedure from the photo 1 2.
Photo 1 Insert 1 2 3 Unplug 1 2 3 5
1-3-1 Installing the Mini PCI card 1. Align the Mini PCI card with the connector at a 45 degree angle. 2. Press the Mini PCI into the connector until you hear a click.
Notices: 1.The connectors are designed to ensure the correct insertion. If you feel resistance, check the connectors & golden finger direction, and realign the card. 2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of the card firmly.
1-3-1.1 Removing the Mini PCI card 1. Release the Mini PCI card by pulling outward the two retaining clips and the card pops up slightly. 2. Lift the mini PCI card out of its connector carefully.
1-4 Packing List* 1 CV700A Board 6 Utility CD Disk 2 DC 12V Power Adapter 7 User's Manual 3 One ATA 100 Flat Cable (2.54mm) 8 SATA DATE Cable (optional) 4 One slim IDE port flat Cable (2.00mm) 9 SATA HDD Power Cable (optional) 5 Power Cable 2 1 3 7 6 5 4 8 9 5 *The packing list above is for the users who purchase single motherboard. The users who purchase the board with chassis may refer to the packing list in the Assembly Guide.
Chapter-2 Hardware Installation This chapter provides the information how to install the hardware of CV700A. Please follow section 1-4, 2-1 and 2-2 to check the delivery package and unpack carefully. Please follow the jumper setting procedure. 2-1 Unpacking Precaution The CV700A board has been well packed with an anti-static bag to protect its sensitive components and circuitry from damage due to static electric discharge. NOTE! 1.
2-2 Unpacking checkup First of all, please follow all necessary steps of section 2.1 to protect CV700A from electricity discharge. With reference to section 1.3, please check the delivery package again with following steps: 1. Unpack the CV700A board and keep all packing material, manual and driver disc etc, do not dispose ! 2. Is there any components lose or drops from the board? DO NOT CONTINUE TO INSTALL THIS BOARD!CONTACT THE DEALER YOU PURCHASED THIS BOARD FROM, IMMEDIATELY. 3.
2-3 Dimension 200x150(mm) 12
2-4 Layout CPU FAN JF2 CN45 JSW1 JR1 CN4 DC12V IN CN5 JKM1 SW1 JP1 JSL1 PW-LED JLED1 HDD-LED LAN-LED EBGA CPU CN3 CN11 CN7 COM1 DIMM1 CN10 CN700 CN13 CN46 VT8237R-Plus JB1 CN16 CN14 CN2 VGA BATTERY JF1 SYS FAN JI1 CN20 CN6 COM2 CN29 CN26 CN9 LAN2 CN28 CN8 LAN3 LAN3 CN18 IDE2 JCF1 CN19 IDE1 13 CN47 JUSB1 JUSB2 CN21 JCF2 SATA1 CN27
2-5 Diagram CPU FAN JF2 JSW1 JR1 CN1 DC12V IN SW1 JP1 CN5 PW-LED HDD-LED LAN-LED CN3 CN7 COM1 DIMM1 CN10 CN13 CN16 CN14 JB1 CN2 VGA CN20 JI1 JF1 SYS FAN CN6 COM2 CN29 CN9 LAN2 CN28 CN47 CN8 LAN3 CN27 CN18 IDE2 CN19 IDE1 CN21 JCF1 JCF2 14 SATA1
2-5-1 Bottom Side Diagram MPCI: Mini PCI Socket . Back Panel (CV700A) PS/2 Mouse Parallel RJ45 LAN 1 RJ45 LAN 2 DC 12V IN USB PS/2 Keyboard COM 1 VGA COM 2 RJ45 LAN 3 .
2-6 Install Memory This motherboard provides one 240-pin DUAL INLINE MEMORY MODULES (DIMM) socket for memory expansion available from minimum memory size of 256MB to maximum memory size of 1GB DDR2 RAM. DDR2 clock supports: DDRII200, DDRII266 Valid Memory Configurations Total Memory DIMM1 System Accept or Not DS/SS Accept Min. ~ Max. 256MB~1GB SS: Single Sided DIMM DS: Double Sided DIMM NOTE! Make sure the total installed memory does not exceed 1GB; otherwise, the system may hang during startup.
NOTE! When you install DIMM module fully into the DIMM socket, the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. WARNING! 2. Once you hear " Beep Beep Beep" sounds after turning on the power , please check if the DRAM is installed properly or not.
2-8 Jumper Setting Description A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2, and 3. You could connect either pin 1 and 2 or 2 and 3. The below figure 2.2 shows the examples of different jumper settings in this manual. Figure 2.2 All jumpers already have its default setting with the plastic cap inserted as ON, or without the plastic cap as OFF.
Note: Do not clear CMOS unless 1. Troubleshooting 2. Forget password 3. You fail over-clocking system JB1 *1-2 2-3 Description *Normal Set CMOS Data clear JB1 3 2 1 3 2 1 *Normal Clear Setting 2-10 JCF2 CF Card Power Voltage select If you use CF card and HDD together, we suggest you use the jumper setup for +5V. JCF2 Description *1-2 *For CF CARD power voltage select +5V 2-3 For CF CARD power voltage select +3.3V JCF2 3 2 1 +5V* * We use to refer to as pin1 19 3 2 1 3.
2-11 JCF1 CF Card Master and Slave selection If you use CF card and HDD together, please set CF as Master and HDD as Slave.
Chapter-3 Connection This chapter provides all necessary information of the peripheral's connections, switches and indicators. Always power off the board before you install the peripherals.
3-2 FAN Connector CV700A provides one CPU fan connector and one system fan connector. CPU Fan Connector- JF2 PIN NO. Description System FAN Connector-JF1 1 FAN Control ON/OFF JF2 pin1 2 +12V 3 FAN speed Sensor JF1 pin1 *Note : DC- in +12V by switch to DC-out voltage +12V So DC -in need stable +12V input 3-3 IDE Connectors PIN NO. There are two kinds of IDE connectors on this board, 40-pin and 44-pin. Each can support up to two IDE-inferface devices.
44 pins(2.0mm)-CN18 (IDE2) This connector supports slim type 2.5" HDD. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks as both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. (See Appendix B) PIN NO. Description PIN NO.
3-4 Compact - Flash Memory Socket C700A configures CompactFlash Storage Card in IDE mode. It will use IDE channel when CompactFlash card is plugged in. This socket supports CF Card Type I/II socket spec. CF Socket 50pin----CN20 PIN NO. Description PIN NO.
3-5 Parallel Port Connector Parallel Port connector is a D-type 25-pin female connector. The On-board Parallel Port can be disabled through the BIOS SETUP (see Chapter 4) . CN10: Printer (LPT)Port ---CN10 D-SUB 25 PIN PIN NO. Description PIN NO.
3-6 Serial Port Connector The CV700A board offers two high speed NSI6C550 compatible UARTS with Read/ Receive 16 byte FIFO serial ports. The serial ports are two DB-9 external connectors. The On-board serial port can be disabled through BIOS SETUP (see Chapter 4). . CN7: COM1 Connector D-SUB 9-Pin PIN NO. Description PIN NO. Description 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND . CN6: COM2 Connector D-SUB 9-pin PIN NO. Description PIN NO.
3-7 Keyboard and Mouse Connector CN5: PS2 Keyboard down side (Din 6 pin jack) PIN NO. Description 1 KB DATA 2 MS DATA 3 GND 4 +5V 5 KB CLOCK 6 MS CLOCK CN5: PS2 Mouse up side (Din 6 pin jack) PIN NO. Description 1 MS DATA 2 NC 3 GND 4 +5V 5 MS CLOCK 6 NC CN5 PS/2 Mouse CN5 PS/2 Keyboard JKM1: 6 PIN (1.25mm Wafer connector) Internal Keyboard / Mouse Connector (Share to CN5) PIN NO.
3-8 USB Port/ Header CN3 (Down side) : USB 0/1port Type A Jack CN27: USB port 4 Type A jack PIN NO. Description PIN NO. Description 1 +5V 1 +5V 2 USB DATA 0/1- 2 USB DATA 6- 3 USB DATA 0/1+ 3 USB DATA 6+ 4 GND 4 GND CN14 / CN16 : USB port 2/3 pin (1.25mm Wafer connector) JUSB1/JUSB2 USB 4/5 port 5pin header (2.54mm) PIN NO. Description PIN NO.
3-9 IR Connector This built-in IR connector supports the optional wireless transmitting and receiving infrared module. It supports Infra-red Data Association (IrDA) and Amplitude Shift Keyed IR (ASKIR). You can configure the setting through the BIOS setup to use the IR function. (see Chapter 4) . JI1: IR connector ---5pin (1.25mm Wafer connector) IR : ASKIR / IRDA PIN NO. Description 1 +5VSB 2 FIR 3 IRRX 4 GND 5 IRTX pin1 JI1 IR 3-10 VGA Connector .
3-11 LAN Port The Fast Ethernet controller provides 32-bit performance, PCI bus master capability, and full compliance with IEEE 802.3 10/100Based-T specification. For 10/100Base-T operation, please connect the network connection by plugging one end of the cable into the RJ-45 jack of the CN9,CN8 Connector. Besides 10/100 Base-T, CV700A can provide Giga LAN solution through CN9,CN8 once equipped with Intel 82541GI/PI/ER chipset. .
3-12 Audio Port Connector The CV700A has an on-board AC'97 3D sound interface. There are the connectors of LINE OUT, MIC-IN and CD-IN connectors. The MIC-IN Jack and CD-IN header are for audio sound input. The LINE-OUT connector is a 4-pin Jack for audio sound output. . CN29 (Phone Jack) -----Line-OUT . CN28 (Phone Jack) -----MIC-IN (3.5mm Phone jack or 5pin 2.54mm header) (3.5mm Phone jack or 5pin 2.54mm header) PIN NO. Description PIN NO.
3-13 DC 12V IN and DC out . CN1: DC 12V-IN External Connector (4pin mini den connector) PIN NO. Description 1,2 +12V DC-IN GND 3,4 CN1 DC 12V IN . CN4: DC 12V-IN Internal Connector (4pin connector) ( For option connector) PIN NO. Description 3,4 +12V DC-IN GND 1,2 3-14 DC +5/+12V output connector . CN21 : DC +5/+12V output connector(2.5mm Wafer) PIN NO.
3-15 Serial ATA . SATA1: S-ATA IDE 7pin Wafer PIN NO. Description 1 GND 2 DATA TX+ 3 DATA TX- 4 GND 5 DATA RX- 6 DATA RX+ 7 GND SATA1 3-16 I 2 C Bus Connector . CN26: I C Bus connector 4pin (1.25mm Wafer connector) 2 PIN NO. Description 1 +3.
3-17 TV-OUT Connector CN13 : TV-OUT S-VIDEO (4pin 1.25mm Wafer) PIN NO. Description 1 LUMA-out 2 CHROMA-out 3 CVBS 4 GND CN13 pin1 3-18 Front-Panel . JR1: System Reset key( 2.0mm pin header) . Power switch: PW-ON--- SW1 JSW1: Power on switch Based on case design , there may be a power switch or a 2-pin header connected to the case-mounted power switch. It is used to power ON/OFF the system. pin1 JSW1 . Power LED: PW-LED / JP1 The Power LED is lit while the system power is on.
Chapter 4 Introduction of BIOS The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS first operates an auto-diagnostic test called POST (Power on Self Test) for all the necessary hardware, it detects the entire hardware devices and configures the parameters of the hardware synchronization.
4-2 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/ Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press . 4-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen.
Standard CMOS Features This Menu is for basic system configurations. Advanced BIOS Features This menu is to set the Advanced Features available in your system. Advanced Chipset Features This menu is to change the values in the chipset registers and optimize your system performance. Integrated Peripherals This menu is to specify your settings for integrated peripherals. Power Management Setup This menu is to specify your settings for power management.
Load Standard Defaults Use this menu to load the BIOS default values for the optimum system performance. Standard Defaults settings are relatively more reliable than Optimized Defaults. All the product verifications, compatibility test reports and manufacture quality controls are based on "Standard Defaults". We suggest you to use this setting for normal operation. "Standard Defaults" is not the slowest setting for this motherboard.
4-5 Advanced BIOS Features Phoenix-AwardBIOS CMOS Setup Utility Advanced BIOS Features Hard Disk Boot Priority Virus Warning CPU L1 & L2 Cache CPU L2 Cache ECC Checking [Press Enter] [Disabled ] [Enabled] [Enabled] Item Help Quick Power On Self Test [Enabled] First Boot Device [USB-FDD] Second Boot Device [HDD-0] Third Boot Device [CDROM] Boot Other Device [Enabled] Boot Up NumLock Status [On] Typematic Rate Setting [Disabled] X Typematic Rate (Chars/Sec) [6] [250] X Typematic Delay (Msec) Security Opti
4-6 Advanced Chipset Features The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer.
4-6-2 AGP & P2P Bridge Control Phoenix- AwardBIOS CMOS Setup Utility AGP & P2P Bridge Control DRAM Clock/Drive Control AGP & P2P Bridge Control [64M] [Enabled] Item Help Menu Level >> ↑↓→←:Move Enter:Select F5:Previous Values +/-/PU/PD:Value F10:Save F6:Fail-Safe Defaults ESC:Exit F1:General Help F7:Optimized Defaults 4-7 Integrated Peripherals Phoenix- AwardBIOS CMOS Setup Utility Integrated Peripherals VIA OnChip IDE Device VIA OnChip PCI Device SuperIO Device [Press Enter] [Press Enter] [Press En
4-7-1 VIA OnChip IDE Device Phoenix-AwardBIOS CMOS Setup Utility VIA OnChip IDE Device OnChip SATA SATA Mode IDE DMA transfer OnChip IDE Channe10 OnChip IDE Channe11 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE HDD Block Mode ↑↓→←:Move Enter:Select F5:Previous Values [Enabled] [IDE] [Enabled] [Enabled] [Enabled] [Enabled] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto]
4-7-3 Super IO Device Phoenix-AwardBIOS CMOS Setup Utility Super IO Device Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port X EPP Mode Select X ECP Mode Use DMA ↑↓→←:Move Enter:Select F5:Previous Values [3F8/IRQ4] [2F8/IRQ3] [378/IRQ7] EPP1.
4-8-1 IRQ / Event Activity Detect IRQs Activity Monitoring Please refer to section4-8-1.1 4-8-1.
4-9 PnP / PCI Configuration Setup This section describes how to configure the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at the speed the CPU itself keeps when CPU communicates with its own special components. This section covers some very technical items and we strongly recommended that only experienced users should make any change to the default settings.
4-10 PC Health Status This section shows the status of your CPU, Fan, and overall system. This is only available when there is Hardware Monitor function onboard. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Temperature/Current System Temp/Current FAN1,FAN2 Speed/ Vcore/3.
4-11 Frequency/Voltage Control This section is to set CPU Frequency Control. Phoenix-AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI Clk Spread Spectrum Item Help [Disabled] [Disabled] Menu Level > ↑↓→←:Move Enter:Select F5:Previous Values +/-/PU/PD:Value F10:Save F6:Fail-Safe Defaults ESC:Exit F1:General Help F7:Optimized Defaults Auto Detect DIMM/PCI Clock This item allows you to enable or disable Auto Detect DIMM/PCI Clock. The settings are Enabled or Disabled.
4-13 Set Supervisor/ User Password You can set supervisor password, user password, or both. The differences are: Supervisor password: You can enter the setup menus and change the options. User password: You can enter the setup menus but do not have the right to change the options. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press .
Chapter 5 DRIVER INSTALLATION There is a SYSTEM INSTALL CD disk in the package. This CD has all the drivers you need and some free application programs and utility programs. In addition, this CD also includes an auto-detect software which can tell you which hardware is installed and which driver is needed so that your system can function properly. We call this auto detect software SYSTEM INSTALL.
Auto install driver Menu 1. VIA 4 IN 1 2. VGA 3. SOUND 4. USB2.0 5. LAN 6. DIRECTX9 7.OTHERS install VIA IDE/AGP/IRQ ROUTING/INF driver install on-board VGA driver install AC97 Audio Codec Installing driver install VIA USB2.0 hardware Installing driver to LAN install driver readme file To install DirectX9 driver readme file To PenMount 6000 install driver readme file Note: PenMount 6000 DRIVER IS TO BE INSTALLED UNDER WIN 2000/XP ONLY.
5-1 VIA 4 IN 1 IDE : AGP: INF : Install VIA IDE/AGP/ INF Driver VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIX COMPATIBILITY ISSUE FOR IDE DEVICES. VIA AGP DRIVER IS TO BE INSTALLED. IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS. VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS. THE DRIVER WILL ENABLE VIA POWER MANAGERMENT CONTROLLER. 1.Click VIA 4 IN 1 when System Install MENU appears.
5.Installing Components List. Click NEXT. 6. This is to announce the Copy Right. Click NEXT. 7.Click Finish to restart computer. NOTE: SYSTEM INSTALL will auto detect file path X:\driver\VIA\CN700\4IN1\setup.exe This driver supports WINDOWS 95\98\98SE\NT4.
5-2 VGA INSTALL CN700 VGA Driver 1. Click VGA when System Install MENU appears. 2. Click NEXT when VIA/S3 CN700 Driver Setup appears. 3. This VIA/S3 CN700 Driver install will begin copying the driver files. Click NEXT. 4. Click FINISH to Restart Computer. NOTE: The path of the file For WINDOWS 98/98SE/ME X:\driver\VIA\CN700\VGA\WIN98me\SETUP.EXE For WINDOWS 2000/XP X:\driver\VIA\CN700\VGA\WIN2KXP\SETUP.
5-3 SOUND Install VIA Audio Codec Driver for VIA 1.Click SOUND when System Install MENU appears. 2. Click NEXT install VIA AC97 Audio Driver 3. Click NEXT install VIA AC97 Audio Driver 4. Click FINISH to Restart Computer. NOTE: The path of the file For WIN98/ME/2K\XP X:\ driver\via\viaudio\setup.
5-4 USB2.0 install VIA USB2.0 Installing driver 1.Click USB2.0 when System Install MENU appears. 2. Click NEXT install USB2.0 Driver NOTE: When you install driver for USB2.0 under Windows 2000.Please install SP4 first. When you install driver for USB2.0 under Windows XP.Please install SP1 first. 4. Click FINISH to Restart Computer. 3. Click NEXT install VIA USB2.0 Driver NOTE: The path of the file For WIN98/ME/2K\XP x:\ driver\via\CN700\USB20\setup.
5-5 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP. Choose INTEGRATE PERIPHERALS. Choose On-Chip Device FUNCTION. Choose " AC97 Audio Disable " on-board sound function by pressing PAGE DOWN KEY to Disable. 5-6 HOW TO UPDATE BIOS In DOS Mode STEP 1. Prepare a boot disc. (you may make one by clicking START, clicking RUN, typing SYS A: , and clicking OK) STEP 2. Copy utility program to your boot disc. You may copy it from DRIVER CD X:\Diver\bios\AWDFLASH.EXE or download it from our web site. STEP 3.
Appendix A: Power Consumption Test Condition Item Spec CPU V4 - C7 1GHz DDR RAM DDR2 533/1GB Operating System Windows XPP/SP2 Test Program 3D Mark 2001SE HDD 3.5" Standard HDD HDD 2.5" Slim Type HDD Mini PCI Card Wireless LAN IEEE802.11g Test Result for reference ! Start up Maximum Stable Hard Disk Stand by Standard HDD 0.10A 2.53A Slim Type HDD 0.10A 1.51A Operation Maximum Shut down Maximum 1.51A 2.12A 1.89A 1.04A 1.67A 1.
Warning ! 1. CF card & 2.5” HDD first boot issue Due to the frequent update and change of Compact Flash card, it can’t always work with 2.5” HDD at the same time. Users may try and get the test result. 2. Battery Battery on board is consumables. Lex doesn’t guarantee the life time of it. 3. Fanless solution with HDD Please be aware of specification & limitation for HDD when fanless solution is implemented.
Warning ! 1. CF card & 2.5” HDD first boot issue Due to the frequent update and change of Compact Flash card, it can’t always work with 2.5” HDD at the same time. Users may try and get the test result. 2. Battery Battery on board is consumables. Lex doesn’t guarantee the life time of it. 3. Fanless solution with HDD Please be aware of specification & limitation for HDD. when fanless solution is implemented.
