IB868 Intel Pentium® M PICMG 1.3 SHB Express CPU Card USER’S MANUAL Version 1.
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium M are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction ....................................................... 1 Product Description ..........................................................1 Checklist ...........................................................................2 Specifications....................................................................3 Board Dimensions.............................................................4 Installations ....................................................... 5 Installing the CPU..
This page is intentionally left blank.
INTRODUCTION Introduction Product Description The IB868 PICMG1.3 SHB board incorporates the Mobile Intel® 915GM Express Chipset for Embedded Computing, consisting of the Intel® 915GM Graphic Memory Controller Hub (GMCH) and Intel® I/O Controller Hub 6-M (ICH6-M), is an optimized integrated graphics solution with a 400 MHz and 533 MHz front-side bus.
INTRODUCTION Checklist Your IB868 Pentium M CPU card package should include the items listed below: • The IB868 CPU Card • This User’s Manual • 1 IDE Ribbon Cable • 1 Floppy Ribbon Connector • SATA Power Cord • SATA Cable • 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a Mounting Bracket • 1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse • 1 CD containing the following: • Chipset Drivers • Flash Memory Utility • Optional audio cable with bracket (Audio8K) • Optional USB cable with bracket
INTRODUCTION Specifications Product Name Form Factor CPU Type CPU Voltage System Speed CPU FSB Cache Green /APM CPU Socket Chipset BIOS Memory VGA LVDS LAN USB Serial ATA Parallel IDE Audio LPC I/O Keyboard/Mouse Edge Connector OnBoard Header/Connector Watchdog Timer Digital I/O System Voltage Other Board Size Golden Finger I/F (Also Backplane Spec.) IB868 PICMG 1.3 SHB Express full size CPU card Intel Pentium M / Celeron M 0.700V ~ 1.708V Up to 2.
INTRODUCTION Board Dimensions 4 IB868 User’s Manual
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB868 in order to set up a workable system. The topics covered are: Installing the CPU ............................................................................6 Installing the Memory.......................................................................7 Setting the Jumpers...........................................................................8 Connectors on IB868 ..........................
INSTALLATIONS Installing the CPU The IB868 board supports a Socket 479 processor socket for Intel® Pentium® M or Celeron® M processors. The processor socket comes with a screw to secure the processor. As shown in the left picture below, loosen the screw first before inserting the processor. Place the processor into the socket by making sure the notch on the corner of the CPU corresponds with the notch on the inside of the socket. Once the processor has slide into the socket, fasten the screw.
INSTALLATIONS Installing the Memory The IB868 board supports two DDR2 memory socket for a maximum total memory of 2GB in DDR2 memory type. Installing and Removing Memory Modules To install the DDR2 modules, locate the memory slot on the board and perform the following steps: 1. Hold the DDR2 module so that the key of the DDR2 module align with those on the memory slot. 2.
INSTALLATIONS Setting the Jumpers Jumpers are used on IB868 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB868 and their respective functions. Jumper Locations on IB868 ...............................................................9 JP2: Panel Voltage Setting ...............................................................
INSTALLATIONS Jumper Locations on IB868 Jumpers on IB868......................................................................... Page JP2: Panel Voltage Setting ...............................................................10 JP3: Clear CMOS Contents..............................................................10 JP5: VGA Signal Select....................................................................10 JP6: CPU Front Side Bus Frequency Setting ..................................
INSTALLATIONS JP2: Panel Voltage Setting JP2 Setting Panel Voltage Pin 1-2 Short/Closed 3.3V Pin 2-3 Short/Closed 5V JP3: Clear CMOS Contents Note that the ATX-power connector should be disconnected from the CPU card before clearing CMOS. JP3 Setting Function Pin 1-2 Short/Closed Normal Pin 2-3 Short/Closed Clear CMOS JP5: VGA Signal Select Use these 2-pin header to select the on board 915GM integrated VGA or from the backplane PCI-EXPRESS*16 External Graphics card.
INSTALLATIONS [ Connectors on IB868 The connectors on IB868 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on IB868 and their respective functions. IDE1, IDE2: EIDE Connectors........................................................13 FDD1: Floppy Drive Connector ......................................................13 CN1, CN2: Serial ATA (SATA) Connectors...................................
INSTALLATIONS Jumper Locations on IB868 Connectors on IB868.................................................................... Page IDE1, IDE2: EIDE Connectors........................................................13 FDD1: Floppy Drive Connector ......................................................13 CN1, CN2: Serial ATA (SATA) Connectors...................................14 FAN1: CPU Fan Power Connector .................................................14 FAN2, FAN3: System Fan Power Connector ........
INSTALLATIONS IDE1, IDE2: EIDE Connectors Signal Name Pin # Reset IDE 1 Host data 7 3 Host data 6 5 Host data 5 7 Host data 4 9 Host data 3 11 Host data 2 13 Host data 1 15 Host data 0 17 Ground 19 DRQ0 21 Host IOW 23 Host IOR 25 IOCHRDY 27 DACK0 29 IRQ14 31 Address 1 33 Address 0 35 Chip select 0 37 Activity 39 FDD1: Floppy Drive Connector Signal Name Pin # Ground 1 Ground 3 Ground 5 Ground 7 Ground 9 Ground 11 Ground 13 Ground 15 Ground 17 Ground 19 Ground 21 Ground 23 Ground 25 Ground 27 FDD1 Ground 29
INSTALLATIONS CN1, CN2: Serial ATA (SATA) Connectors The SATA connectors support serial ATA 150. Each connector can only use one serial ATA hard disk. CN2 is port 1 and CN1 is port 2. FAN1: CPU Fan Power Connector FAN1 is a 3-pin header for the CPU fan. The fan must be a 12V fan. Pin # 1 2 3 Signal Name Ground +12V Rotation detection FAN2, FAN3: System Fan Power Connector FAN2 and FAN3 are 3-pin headers for system fans. The fan must be a 12V fan.
INSTALLATIONS J2: System Function Connector J2 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. J2 is a 20-pin header that provides interfaces for the following functions.
INSTALLATIONS Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header. Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.
INSTALLATIONS J6: Panel Inverter Power Connector Pin # Signal Name 1 +12V 2 ENABKL 3 Ground Remarks: Maximum current is 1A. J7, J8 , J9: USB Connectors The following table shows the pin outs of the USB pin headers connectors. Overall, the two pin headers support four USB ports.
INSTALLATIONS J11: Parallel Port Connector Signal Name Line printer strobe PD0, parallel data 0 PD1, parallel data 1 PD2, parallel data 2 PD3, parallel data 3 PD4, parallel data 4 PD5, parallel data 5 PD6, parallel data 6 PD7, parallel data 7 ACK, acknowledge Busy Paper empty Select J11 Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 Pin # 14 15 16 17 18 19 20 21 22 23 24 25 N/A Signal Name AutoFeed Error Initialize Select Ground Ground Ground Ground Ground Ground Ground Ground N/A J13: Digital input / output Con
INSTALLATIONS J15: Wake On LAN Connector J15 is a 3-pin header for the Wake On LAN function on the motherboard. The following table shows the pin out assignments of this connector. Wake On LAN will function properly only with an ATX power supply with 5VSB that has 1A. Pin # Signal Name 1 +5VSB 2 Ground 3 LAN Wakeup J16, J17: External PS/2 Mouse and Keyboard Connector Pin # 1 2 3 4 5 J17 KB clock KB data N.C. Ground Vcc J16 Mouse data N.C.
INSTALLATIONS J20: Primary RJ45 Connector J20 is the primary RJ-45 connector based on the chipset integrated LAN. The figure below shows the pin out assignments of the connector and its corresponding input jack. J21: Gigabit LAN RJ45 Connector J21 is the Gigabit LAN RJ45 connector. J22: External Audio Connector J22 is a 12-pin header that is used to connect to the optional audio cable that integrates jacks for Line In, Line Out and Mic.
BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction.............................................................................22 BIOS Setup........................................................................................22 Standard CMOS Setup......................................................................24 Advanced BIOS Features.........................
BIOS SETUP BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving ESC : Quit F10 : Save & Exit Setup á â à ß : Select Item Time, Date, Hard Disk Type… The section below the setup items of the Main Menu display
BIOS SETUP Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the motherboard is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
BIOS SETUP To set the date, highlight the “Date” field and use the PageUp/ PageDown or +/- keys to set the current time. Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the / or +/- keys to set the current time. IDE Channel Master/Slave The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices.
BIOS SETUP Video This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt On This field determines whether or not the system will halt if an error is detected during power up. No errors The system boot will not be halted for any error that may be detected.
BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference.
BIOS SETUP Quick Power On Self Test When enabled, this field speeds up the Power On Self Test (POST) after the system is turned on. If it is set to Enabled, BIOS will skip some items. First/Second/Third Boot Device These fields determine the drive that the system searches first for an operating system. The options available include Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-Floppy, USB-ZIP, USB-CDROM, LAN and Disable.
BIOS SETUP Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. Security Option This field allows you to limit access to the System and Setup. The default value is Setup. When you select System, the system prompts for the User Password every time you boot up.
BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset.
BIOS SETUP DRAM RAS# Precharge This option sets the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes. The default setting for the Active to Precharge Delay is 4. Precharge Delay (tRAS) The default setting for the Precharge Delay is 12. System Memory Frequency The default setting is 533MHz. SLP_S4# Assertion Width The default setting is 1 to 2 Sec.
BIOS SETUP Panel Scaling The default setting is Auto. The options available include On and Off. Panel Number These fields allow you to select the LCD Panel type. The default values for these ports are: 640x480 800x600 1024x768 1280x1024 1280x768 1400x1050 1600x1200 18bit 18bit 18bit 18bit 18bit 18bit 18bit SC SC SC DC SC DC DC Onboard PCI-E LAN By default, this setting is enabled. LAN PXE Option ROM By default, this setting is disabled. Other selections include ICH6 Integrated LAN and Marvell PCI-E LAN.
BIOS SETUP Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main items for user to select. Once an item selected, a submenu appears. Details follow.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility SuperIO Device POWER ON Function KB Power ON Password Hot Key power ON Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD , TxD Active IR Transmission Delay UR2 Duplex Mode Use IR Pins PWRON After PWR-Fail BUTTON ONLY Enter Ctrl-F1 Enabled 3F8/IRQ4 2F8/IRQ3 Normal Hi, Lo Disabled Half IR-Rx2Tx2 Off ITEM HELP Menu Level > IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to tran
BIOS SETUP On-Chip Serial ATA Setting The fields under the SATA setting includes SATA Mode (IDE), On-Chip Serial ATA (Auto), PATA IDE Mode (Secondary) and SATA Port (PO, P2 is Primary). USB Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. USB 2.0 Controller The options for this field are Enabled and Disabled. By default, this field is set to Enabled. In order to use USB 2.0, necessary OS drivers must be installed first.
BIOS SETUP Onboard Serial Port These fields allow you to select the onboard serial ports and their addresses. The default values for these ports are: Serial Port 1 3F8/IRQ4 Serial Port 2 2F8/IRQ3 UART Mode Select This field determines the UART 2 mode in your computer. The default value is Normal. Other options include IrDA and ASKIR. PWRON After PWR-Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation.
BIOS SETUP ACPI Suspend The default setting of the ACPI Suspend mode is S1(POS). RUN VGABIOS if S3 Resume The default setting of this field is Auto. Power Management This field allows you to select the type of power saving management modes. There are four selections for Power Management. Min. Power Saving Minimum power management Max. Power Saving Maximum power management. User Define Each of the ranges is from 1 min. to 1hr. Except for HDD Power Down which ranges from 1 min. to 15 min.
BIOS SETUP Soft-Off by PWRBTN This field defines the power-off mode when using an ATX power supply. The Instant Off mode allows powering off immediately upon pressing the power button. In the Delay 4 Sec mode, the system powers off when the power button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds. Wake up by PCI Card By default, this field is disabled.
BIOS SETUP PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Shutdown Temperature CPU Warning Temperature Current System Temp Current CPU TEMP System FAN Speed CPU FAN Speed Disabled Disabled 45°C/113°F 45°C/113°F 5400 RPM 5400 RPM Vcore(V) 1.02 V 12 V 1.32 V 1.8V 1.8V +5V 5.25 V 3.3V VBAT (V) ITEM HELP Menu Level > 3.37V 3.
BIOS SETUP Frequency/Voltage Control This section shows the user how to configure the processor frequency. Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI Clk Disabled Spread Spectrum Modulated Disabled ITEM HELP Menu Level > Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock. Spread Spectrum Modulated This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only.
BIOS SETUP Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. Load Optimized Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. Set Supervisor Password These two options set the system password.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 2000 and Windows XP. The software and drivers are included with the motherboard. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel Chipset Software Intallation Utility..........................44 VGA Drivers Installation.................................................
DRIVERS INSTALLATION Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 2000/XP. 1. Insert the CD that comes with the board. Click Intel Chipsets and then Intel(R) 915GMChipset Drivers. 2. Click Intel(R) Chipset Software Installation Utility. 3.
DRIVERS INSTALLATION 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVERS INSTALLATION VGA Drivers Installation To install the VGA drivers, follow the steps below to proceed with the installation. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) 915GMChipset Drivers. 2. Click Intel(R) 915GMChipset Family Graphics Driver. 3. When the Welcome screen appears, click Next to continue.
DRIVERS INSTALLATION 4. Click Yes to to agree with the license agreement and continue the installation. 5. Restart the computer as promted and for changes to take effect. IMPORTANT NOTE: When you have restarted the computer, your computer screen will be blank. At this point, press CTRL-ALT-F1 simultaneously, if you are using CRT monitor. If you are using LVDS LCD panel, press CTRL-ALT-F3. If you are using DVI monitor, press CTRL-ALT-F4.
DRIVERS INSTALLATION AC97 Codec Audio Driver Installation Follow the steps below to install the Realtek AC97 Codec Audio Drivers. 1. Insert the CD that comes with the motherboard. Click Intel Chipsets and then Intel(R) 915GMChipset Drivers. 2. Click Realtek AC'97 Codec Audio Driver. 3. Click Finish to restart the computer and for changes to take effect. .
DRIVERS INSTALLATION LAN Drivers Installation Follow the steps below to complete the installation of the Intel PRO LAN drivers. 1. Insert the CD that comes with the motherboard. Click LAN Card and then Intel(R) PRO LAN Drivers. 2. Click Install Base Software to continue. 3. When prompted, please to restart the computer for new settings to take effect.
DRIVERS INSTALLATION Follow the steps below to install the Marvell Gigabit LAN drivers. 1. Insert the CD that comes with the motherboard. Click LAN Card and then Marvell LAN Controller Driver. 2. Click Next when the InstallShield Wizard welcome screen appears. 3. Click Next to agree with the license agreement. 4. Click Next when the Readme Information screen appears to proceed with the drives installation process. 5. When the Installation is complete, click Finish for the changes to take effect.
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.
APPENDIX C. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
APPENDIX void copyright(void) { printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO DETECT) ========\n"\ " Usage : W627E_WD reset_time\n"\ " Ex : W627E_WD 3 => reset system after 3 second\n"\ " W627E_WD 0 => disable watch dog timer\n"); } //=========================================================================== void EnableWDT(int interval) { unsigned char bBuf; bBuf = Get_W627EHF_Reg( 0x2D); bBuf &= (!0x01); Set_W627EHF_Reg( 0x2D, bBuf); //Enable WDTO Set_W627EHF_LD( 0x08); Set_W627EHF_Reg(
APPENDIX W627EHF_BASE = 0x4E; result = W627EHF_BASE; ucDid = Get_W627EHF_Reg(0x20); if (ucDid == 0x88) { goto Init_Finish; } W627EHF_BASE = 0x00; result = W627EHF_BASE; Init_Finish: return (result); } //=========================================================================== void Unlock_W627EHF (void) { outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK); outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK); } //=========================================================================== void Lock_W627EHF (void) { outp
APPENDIX //=========================================================================== // // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
