User’s Manual 2801550 LGA775 Pentium 4 Intel 865G Industrial Motherboard
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
Table of Contents Introduction .......................................................1 Product Description............................................................. 1 Checklist.............................................................................. 2 Specifications ...................................................................... 3 Board Dimensions ............................................................... 4 Installations .......................................................
This page is intentionally left blank.
INTRODUCTION Introduction Product Description The world's first Pentium 4 LGA775 industrial motherboard based on the Intel® 865G chipset, 2801550, supports processor FSB of 533/800MHz for processor speeds of up to 3.8GHz. With two DDR memory socket on board, the motherboard accommodates a maximum memory capacity of 2GB. Integrated chipset-graphics features CRT VGA support with up to 64MB shared memory, while Ethernet functionality is provided by an Intel® 10/100Mb and an optional Gigabit Ethernet.
INTRODUCTION Checklist Your 2801550 package should include the items listed below.
INTRODUCTION Specifications Form Factor CPU Type System Speed CPU Operating Frequency Green /APM CPU Socket Chipset BIOS Cache VGA AGP port st LAN nd LAN Audio Memory type LPC I/O Secondary IO RTC/CMOS Battery Keyboard Controller EPP/ECP IDE CF connector Serial ATA connector Board Size D-type connectors Power Connector Expansion Slots PCI to ISA Bridge USB IrDA Digital I/O Watchdog Timer System Voltages ATX LGA 775 (Intel® Pentium® 4 / Celeron D) 2.53GHz~3.8GHz 533MHz / 800MHz APM1.
INTRODUCTION Board Dimensions 4 2801550 User’s Manual
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the 2801550 in order to set up a workable system. The topics covered are: Installing the CPU........................................................................ 6 ATX Power Installation ............................................................... 6 Installing the Memory .................................................................. 7 Setting the Jumpers ......................................
INSTALLATIONS Installing the CPU The 2801550 motherboard supports a LGA 775 processor socket for Intel® Pentium® 4 processors. The LGA 775 processor socket comes with a lever to secure the processor. Refer to the pictures below, from left to right, on how to place the processor into the CPU socket. Please note that the cover of the LGA775 socket must always be installed during transport to avoid damage to the socket.
INSTALLATIONS Installing the Memory The 2801550 motherboard supports two DDR memory sockets for a maximum total memory of 2GB in DDR memory type. The memory module capacities supported are 64MB, 128MB, 256MB, 512MB and 1GB. The following table lists the supported DDR DIMM configurations. Intel 865G supports configurations defined in the JEDEC DDR DIMM specification only (A,B,C). Non-JEDEC standard DIMMs such as double-sided x16 DDR SDRAM DIMMs are not supported. Supported DDR DIMM Configurations.
INSTALLATIONS Setting the Jumpers Jumpers are used on 2801550 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on 2801550 and their respective functions. Jumper Locations on 2801550.......................................................... 9 Configuring the CPU Frequency ..................................................
INSTALLATIONS Jumper Locations on 2801550 Jumpers on 2801550 ...................................................................Page JP1, JP2, JP3: RS232/422/485 (COM2) Selection ....................... 10 JP4: Clear CMOS Contents .......................................................... 10 JP5: 10/100Mb LAN Enable/Disable...........................................
INSTALLATIONS Configuring the CPU Frequency The 2801550 motherboard does not provide DIP switches to configure the processor speed (CPU frequency). The CPU frequency and processor side bus of the processor can be automatically detected by the motherboard. JP1, JP2, JP3: RS232/422/485 (COM2) Selection COM1 is fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485. COM3 and COM4 are fixed for RS-232 use only. The following table describes the jumper settings for COM2 selection.
INSTALLATIONS JP5: 10/100Mb LAN Enable/Disable If your motherboard comes with the Gigabit LAN functionality, you can use this jumper to enable or disable it.
INSTALLATIONS Connectors on 2801550 The connectors on 2801550 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on 2801550 and their respective functions. Connector Locations on 2801550................................................... 13 ATX1: ATX Power Supply Connector......................................... 14 FDD1: Floppy Drive Connector ...................................................
INSTALLATIONS Connector Locations on 2801550 Connectors on 2801550 ................................................................................................... Page ATX1: ATX Power Supply Connector........................................................................................ 14 FDD1: Floppy Drive Connector .................................................................................................. 14 IDE1, IDE2: EIDE Connectors........................................................
INSTALLATIONS ATX1: ATX Power Supply Connector Signal Name 3.3V -12V Ground PS-ON Ground Ground Ground -5V +5V +5V +5V Ground Pin # 13 14 15 16 17 18 19 20 21 22 23 24 Pin # 1 2 3 4 5 6 7 8 9 10 11 12 Signal Name 3.3V 3.3V Ground +5V Ground +5V Ground Power good 5VSB +12V +12V +3.3V FDD1: Floppy Drive Connector FDD1is a slim 26-pin connector and will support up to 1.44MB FDD.
INSTALLATIONS IDE1, IDE2: EIDE Connectors IDE1: Primary IDE Connector Signal Name IDE1 Reset IDE Host data 7 Host data 6 Host data 5 Host data 4 Host data 3 Host data 2 Host data 1 Host data 0 Ground DRQ0 Host IOW Host IOR IOCHRDY DACK0 IRQ14 Address 1 Address 0 Chip select 0 Activity 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Ground Host data 8 Host data 9 Host data 10 Host data 11 Host data 12 Host data 13 Host data 14 Host data 15
INSTALLATIONS FAN1: CPU Fan Power Connector 1 2 3 4 Signal Name Ground +12V Rotation detection NC FAN2: Chassis Fan Power Connector FAN2 is a 3-pin header for the chassis fan. The fan must be a 12V fan. 1 2 3 Signal Name Ground +12V Rotation detection FAN3: System Fan Power Connector FAN3 is a 3-pin header for a 12V fan. 1 2 3 Signal Name Ground +12V Rotation detection CN1: PS/2 Keyboard and PS/2 Mouse Connectors PS/2 Mouse PS/2 Keyboard Below are the pin-out assignments of the connectors.
INSTALLATIONS CN2, J1, J10, J13: Serial Ports CN2 (COM1) is a DB-9 connector, while J1 (COM2), J10 (COM3) and J13 (COM4) are pin headers. COM1 Signal Name DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground COM2/COM3/COM4 Pin # 1 2 3 4 5 Pin # 6 7 8 9 10 Signal Name DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used J1 (COM2) is jumper selectable for RS-232, RS-422 and RS-485.
INSTALLATIONS CN3: Parallel Port Connector CN3 is a DB-25 external. The following table describes the pin-out assignments of this connector.
INSTALLATIONS CN5: USB and 10/100Mb LAN RJ45 Connectors CN5 consists of an 10/100 RJ-45 connector (top) and two stacked USB ports. Refer to the section below for their respective pin assignments. USB0 USB1 Pin # 1 2 3 4 Signal Name Vcc USBUSB+ Ground CN6: USB and Gigabit LAN RJ45 Connectors CN6 consists of a Gigabit RJ-45 connector (top) and two stacked USB ports. Refer to the section below for their respective pin assignments.
INSTALLATIONS J2: Digital 4-in 4-out I/O Connector Ground Out3 Out2 IN3 IN2 1 3 5 7 9 2 4 6 8 10 Signal Name Vcc Out1 Out0 IN1 IN0 J4: IrDA Connector 1 2 3 4 5 Signal Name +5V No connect Ir RX Ground Ir TX J5: ATX 12V Power Connector Signal Name Ground Ground +12V +12V 1 2 3 4 J6: Compact Flash Connector J7, J8: Serial ATA (SATA) Connectors 1 2 3 4 5 6 7 20 Signal Name GND TXP TXN GND RXN RXP GND 2801550 User’s Manual
INSTALLATIONS J9: CD-In Audio Connector Pin # 1 2 3 4 Signal Name CD Audio L Ground Ground CD Audio R J11: External Audio Connector J11 is a 6-pin header that is used to connect to the optional audio cable card that integrates jacks for Line Out and Mic. LINEOUT_L Ground MIC 1 1 3 5 Signal Name LINEOUT_R Ground MIC 2 2 4 6 J12: USB Connector J12 connector will support the 3rd and 4th USB ports.
INSTALLATIONS J15: System Function Connector J15 provides connectors for system indicators that provide light indication of the computer activities and switches to change the computer status. Hard Disk Drive LED Reset Switch Not Defined ATX Power On Switch SMI / Hardware Switch Power LED Speaker Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8-ohm speaker is recommended.
INSTALLATIONS SMI/Hardware Switch: Pins 6 and 16 This connector supports the "Green Switch" on the control panel, which, when pressed, will force the system into the power-saving mode immediately. Signal Name 6 16 SMI Ground ATX Power ON Switch: Pins 7 and 17 This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off.
INSTALLATIONS Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sort of circumstances, the timer will count to zero and the selected outputs will be driven. Under normal circumstance, the user will restart the WDT at regular intervals before the timer counts to zero.
INSTALLATIONS mov al, 01h mov cl, 30h call Write_Reg ;watchdog enabled call Lock_Chip ret Enable_And_Set_Watchdog Endp ;[]=============================================== ; Name : Disable_Watchdog ; IN : None ; OUT : None ;[]=============================================== Disable_Watchdog Proc Near call Unlock_Chip mov cl, 07h mov al, 08h call Write_Reg ;switch to LD8 xor al, al mov cl, 0F6h call Write_Reg ;clear watchdog timer xor al, al mov cl, 30h call Write_Reg ;watchdog disabled call Lock_Chip
INSTALLATIONS ;[]================================================ Unlock_Chip Proc Near mov dx, 2Eh mov al, 0AAh out dx, al ret Unlock_Chip Endp ;[]================================================ ; Name : Write_Reg ; IN : CL - register index ; AL - Value to write ; OUT : None ;[]================================================ Write_Reg Proc Near push ax mov dx, 2Eh mov al,cl out dx,al pop ax inc dx out dx,al ret Write_Reg Endp ;[]================================================ ; Name : Read_Reg ; IN : C
BIOS SETUP BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the motherboard. The topics covered in this chapter are as follows: BIOS Introduction ................................................................................ 28 BIOS Introduction ................................................................................ 29 BIOS Setup ............................................................................................ 29 Standard CMOS Setup.
BIOS SETUP BIOS Introduction This chapter describes the different settings available in the Award BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction ..................................................................... 29 BIOS Setup ................................................................................. 29 Standard CMOS Setup .............................................................. 31 Advanced BIOS Features..................................
BIOS SETUP BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel® Pentium® 4 processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
BIOS SETUP Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup PC Health Status Exit Without Saving ESC : Quit F10 : Save & Exit Setup Ç È Æ Å : Select Item Time, Date, Hard Disk Type The section below the setup items of the Main Menu displa
BIOS SETUP Standard CMOS Setup “Standard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the board is already installed in a working system, you will not need to select this option. You will need to run the Standard CMOS option, however, if you change your system hardware configurations, the onboard battery fails, or the configuration stored in the CMOS memory was lost or damaged.
BIOS SETUP Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the / or +/- keys to set the current time. IDE Primary HDDs / IDE Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices. Each channel can support up to two hard disks; the first is the “Master” and the second is the “Slave”.
BIOS SETUP Video This field selects the type of video display card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt On This field determines whether or not the system will halt if an error is detected during power up. No errors The system boot will not be halted for any error that may be detected.
BIOS SETUP Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features Press Enter Press Enter Disabled Enabled Enabled Enabled Floppy Hard Disk CDROM Enabled Disabled Disabled On Fast Disabled 6 250 Setup Enabled 1.
BIOS SETUP Hard Disk Boot Priority This item allows you to set the priority for hard disk boot. When you press enter, the selections shows the current hard disks used in your system as well as the Bootable Add-in Card that is relevant to other boot sources media such as SCSI cards and LAN cards. Virus Warning This item protects the boot sector and partition table of your hard disk against accidental modifications. If an attempt is made, the BIOS will halt the system and display a warning message.
BIOS SETUP Swap Floppy Drive This item allows you to determine whether or not to enable Swap Floppy Drive. When enabled, the BIOS swaps floppy drive assignments so that Drive A becomes Drive B, and Drive B becomes Drive A. By default, this field is set to Disabled. Boot Up Floppy Seek This feature controls whether the BIOS checks for a floppy drive while booting up. If it cannot detect one (either due to improper configuration or its absence), it will flash an error message.
BIOS SETUP MPS Version Control for OS This option is specifies the MPS (Multiprocessor Specification) version for your operating system. MPS version 1.4 added extended configuration tables to improve support for multiple PCI bus configurations and improve future expandability. The default setting is 1.4. OS Select for DRAM > 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS/2 that depends on certain BIOS calls to access memory. The default setting is Non-OS/2.
BIOS SETUP Advanced Chipset Features This Setup menu controls the configuration of the chipset. Phoenix - AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable CAS Latency Time Active to Precharge Delay DRAM RAS# to CAS# Delay DRAM RAS# Precharge Memory Frequency For System BIOS Cacheable Video BIOS Cacheable Memory Hole At 15M-16M AGP Aperture Size (MB) By SPD 2.
BIOS SETUP Memory Frequency For This field sets the frequency of the DRAM memory installed. The default setting is Auto. The other settings are DDR266,DDR320 and DDR400. System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result.
BIOS SETUP Integrated Peripherals Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals On-Chip Primary IDE Device Press Enter Onboard Device SuperIO Device Press Enter Press Enter ITEM HELP Menu Level Phoenix - AwardBIOS CMOS Setup Utility OnChip IDE Device IDE Block Mode On-Chip Primary PCI IDE IDE Primary Master PIO IDE Primary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA On-Chip Secondary PCI IDE IDE Secondary Master PIO IDE Secondary Slave PIO IDE Secondary Master UDMA IDE Sec
BIOS SETUP IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive. OnChip Primary/Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. IDE Primary/Secondary Master/Slave PIO These fields allow your system hard disk controller to work faster.
BIOS SETUP AC97 Audio The default setting of the AC97 Audio is Auto. CSA LAN (Giga-LAN) The field enables or disables this Intel Giga BaseT Ethernet controller. Init Display First By default, the system initializes the PCI Slot VGA when the system boots. Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
BIOS SETUP Power Management Setup The Power Management Setup allows you to save energy of your system effectively.
BIOS SETUP Video Off In Suspend When enabled, the video is off in suspend mode. The default setting is Yes. Suspend Type The default setting for the Suspend Type field is Stop Grant. Modem Use IRQ This field sets the IRQ used by the Modem. By default, the setting is 3. Suspend Mode When enabled, and after the set time of system inactivity, all devices except the CPU will be shut off.
BIOS SETUP Reload Global Timer Events The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode. When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service.
BIOS SETUP PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all installed PCI cards must be set to this value.
BIOS SETUP PC Health Status This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds and voltages. Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Hardware Monitor CPU Warning Temperature System Temp. CPU Te mp CPU FAN Speed (FAN1) System FAN Speed (FAN2) System FAN Speed (FAN3) Vcore(V) Enabled Disabled 28°C/82°F 42°C/107°F 5400 RPM 5463 RPM 5388 RPM 1.02 V +3.3V +5V +12V -12V Shutdo wn Temperature CPU Fan Failure Warning Sys.
BIOS SETUP Frequency/Voltage Control This section shows the user how to configure the processor frequency. Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control CPU Clock Ratio Auto Detect PCI Clk 14X Disabled Spread Spectrum Disabled ITEM HELP Menu Level CPU Clock Ratio The CPU Ratio, also known as the CPU bus speed multiplier, can be configured through this field. The default setting is 14X. This parameter can be used in conjunction with the above field to change the processor s speed.
BIOS SETUP Load Fail-Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high-performance features. Load Setup Defaults This option allows you to load the default values to your system configuration. These default settings are optimal and enable all high performance features. Set Supervisor/User Password These two options set the system password.
BIOS SETUP This page is intentionally left blank.
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98, Windows NT 4.0 and Windows 2000. The software and drivers are included with the board. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel 865G Chipset Software Intallation Utility ................ 52 Intel 865G Chipset Graphics Driver..................................
DRIVERS INSTALLATION Intel 865G Chipset Software Intallation Utility The Intel 865G Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 98/98SE/ME/2000/XP. 1. Insert the CD that comes with the board and the screen below would appear. Click Intel Chipsets and then Intel 865G Chipset Family Drivers. 2.
DRIVERS INSTALLATION 3. When the Welcome screen appears, click Next to continue. 4. Click Yes to accept the software license agreement and proceed with the installation process.
DRIVERS INSTALLATION 5. On Readme Information screen, click Next to continue the installation. 6. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVERS INSTALLATION Intel 865G Chipset Graphics Driver The Intel 865G Chipset Family Graphics Drivers come in the CD with the board . Follow the instructions below to complete the installation under Windows 98/98SE/ME/2000/XP. 1. Insert the CD that comes with the board and the screen below would appear. Click Intel Chipsets and then Intel 865G Chipset Family Drivers. 2. When the Welcome screen appears, click Next to continue.
DRIVERS INSTALLATION 3. Click Yes to accept the software license agreement and proceed with the installation process. 4. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. When the computer has restarted, the system will be able to find some devices. Restart your computer when prompted.
DRIVERS INSTALLATION Realtek AC97 Codec Audio Driver Installation Follow the steps below to install the Realtek AC97 Codec Audio Drivers. 1. Insert the CD that comes with the board and the screen below would appear. Click Intel Chipsets, then Intel 865G Chipset Family Drivers. Click Realtek AC97 Codec Audio Drivers to start installation. 2. Click Finish to restart the computer and for changes to take effect. .
DRIVERS INSTALLATION Intel PRO LAN Drivers Installation The Intel PRO LAN drivers support both Intel® PRO/100 and PRO/1000 drivers. Follow the steps below to complete the installation. 1. Insert the CD that comes with the board and the screen below would appear. Click on LAN Card on the left side to make the LAN drivers selection. Click on Intel(R) PRO LAN Drivers. 2. Click Install Now. 3. Click Restart to restart the computer and new settings to take effect.
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used.
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board.
Any advice or comments about our products and service, or anything we can help you with please don t hesitate to contact with us. We will do our best to support you for your products, projects and business Global American Inc. Address 17 Hampshire Drive Hudson, NH 03051 TEL Toll Free (U.S. Only) 800-833-8999 (603)886-3900 FAX (603)886-4545 Website http://www.globalamericaninc.com E-Mail salesinfo@globalamericaninc.
