Quick Start Guide Page 2

ManualsBrandsIntel ManualsOtherIntel Server Board S5520UR

A complete list of accessories and spares can be found at:

http://www.intel.com/p/en_US/support/highlights/server/s5520ur

Front Panel Controls and Indicators

Intel® Local Control Panel Standard Control Panel

O M L K J HIN G

J IL K

BA F G HEDC

A NIC2 Activity LED

B. NIC1 Activity LED

C. Power/Sleep Button

D. Power/Sleep LED

E. Hard Drive

Activity LED

F. Status LED

G. System ID LED

H. System ID

Button

I. Reset

Button

J. USB 1.1

Port

K. NMI

(recessed)

Button

L. Video (hot-

swap drive

system only)

A USB 1.1 Port

B. LCD Display

C. Menu Control Button - Up

D. Menu Control Button - Down

E. Menu Control Button - Left

F. Menu Control Button - Enter

G. ID LED

H. Power/Sleep LED

I. Power/Sleep Button

J. System Status

LED

K. NIC 2 Activity

LED

L. NIC 1 Activity LED

M. HDD Activity LED

N. Reset Button

O. USB 1.1 Port

Install Top Cover

Note:

Security screw

re-installation is optional.

Place cover as shown, slide forward

to engage recessed edge at

front of cover. Make sure

latch is locked.

Recessed

Edge

Install Rack

Handles

Note: Rack handles are required to

install the bezel. For instructions,

see the Service Guide.

Install Intel® Local Control Panel (optional)

Press the blue locking lever at the

back of the control panel and push

it forward to release it

from the chassis.

Disconnect the front panel and USB

cables from the backplane as shown.

Slide the control

panel and cables

out of the chassis.

Slide control panel fully into chassis until

the locking lever engages.

Feed local control panel cables into chassis opening.

Connect the USB and data cables to the local control panel as

shown.

Connect the two cables to the USB

and front panel connectors on the

backplane as shown.

Remove Standard Control Panel Install Local Control Panel

Locking

Lever

Server

Board

Local

Control Panel

Backplane

Note: The Intel

Local Control Panel option is only supported in hot-swap drive systems.

Install PCI Add-in Card

Riser Assembly

PCI Riser

Socket

Chassis

Slots (2)

Hooks (2)

Riser Card

Edge Connector

Processor

Air Duct

Slot

Position riser card edge connector over

the server board riser socket and align

the two hooks in the riser with the slots

at the back of the chassis.

Press down uniformly until the

two hooks on the rear of the

PCI riser assembly

engage the chassis

back panel slots.

The riser card will seat

into the matching riser

socket on the server

board.

Note that the riser assembly card edge installs in

the slot in the processor air duct.

Install Add-in Card

(optional)

Remove filler panel from the add-in card slot.

Insert add-in card until it seats in riser connector.

Secure the add-in card with screw as shown.

CAUTION:

Observe normal

ESD precautions

when installing

the add-in card.

Riser Connector

REMOVE Filler Panel

Remove the screw as shown.

Install Processor

Air Duct

Use care to avoid

pinching system

cables.

Processor

Air Duct

Install processor

air duct as shown

making sure the front

edge of the duct aligns

correctly with the notches

on the fan module.

Install Hot-swap Drive System Components ...

for a Fixed Drive System, go to Step 12

Position backplane over

six chassis standoffs.

Engage standoffs

and slide the

backplane in the

direction shown

to lock into place.

Tighten blue

thumbscrew.

Install the Backplane

Note: Both the active and passive backplanes install the same.

Open the backplane bridge board connector

retention

clip.

Install the Bridge Board

Route the five fan

module cables over

the fan guard and

connect to the

corresponding

connectors on the

backplane.

Connect the USB and

data cables from the

control panel to the

USB and front panel

connectors on the

backplane.

Make Cable Connections

Connect the power

supply cable to the

power connector

located on the

backplane.

Passive Backplane Only: Connect the

hard drive SATA cables from the server

board to the corresponding SATA

connectors on the backplane.

Active Backplane

Server

Board

Bridge Board

Install bridge board making

sure the connector edges on

both sides align correctly

with the slots, and by

pressing down on both

sides simultaneously.

Close the retention clips.

Install Hot-swap Hard Drives

Drive 0 Primary

Hard Drive Numbering Diagram

Repeat these steps for each

installed hard drive.

Remove hot-swap drive

carrier(s) by pushing

green latch towards the lever,

opening the lever all the way,

and then pulling the drive

carrier out of the system.

Remove the plastic air

baffle and save for

future use.

Install the hard disk

drive and attach

with four

screws.

With the carrier lever in the

OPEN position, slide drive

assembly into chassis

until it stops, then

close the lever until

it snaps shut.

CAUTION: If you install less than three drives or devices, empty drive bays must be

occupied by carriers with baffles to maintain proper system cooling. To avoid possible

damage to your chassis, use only carriers that came with your server system.

Install Air Bafﬂe

Cabling Legend:

• Main Power Cable

• CPU Power Cable

• Power Signal Cable

• Optical Drive Data Cable

• SATA 0-2 HDD Data Cables

(passive backplane only)

Route all applicable

cables (see the ‘Cabling Legend’

below) through the baffle

notches and snap air

baffle into place.

The baffle is held in place by two

snap-standoffs on the chassis floor.

Note: Front tab

of air baffle must fit

under the drive bay

cover prior to lowering

into chassis standoffs

to ensure a proper fit.

Make sure that all the

cables are seated over

the backplane.

SATA 0

SATA 1

SATA 2

Passive

Backplane

Fan Connectors

Fan Module

SATA 0

SATA 1

SATA 2

SATA

Connector

Detail

SATA Conn.

Details

Server Board

Snap

Stand-offs

Power Signal

Main Power

CPU Power

SATA Connector

SATA Connectors

Power

Supply

SATA 0 HDD

SATA 1 HDD

Optical Drive

Front

Tab

SATA 2 HDD

Standoff Detail

Air Baffle

USB

Cable

Data

Cable

Install Fixed Drive System Components...for a Hot-swap Drive System, go to Step 11

SATA 0

SATA 1

SATA 2

Backplane

Fixed

Drive 1

Power

Supply

Cable

Connector

Install Hard Drive Cables

Connect SATA data cable(s) to server board as shown.

Connect opposite end of SATA data cable(s) to

hard drive(s) as shown ... see detail below.

Connect the SATA fixed drive power

connectors to each hard drive

as shown ... see detail.

BLUE indicates Data Cable

RED indicates Power Cable

Cable

Legend

Data

Power

Back View of

SATA Drive

Server

Board

Install Air Bafﬂe

Standoff Detail

Front

Tab

Main Power

CPU Power

Power Signal

SATA Connector

Cabling Legend:

• Main Power Cable

• CPU Power Cable

• Power Signal Cable

• Optical Drive

Data Cable

• SATA 0-2 HDD

Data Cables

• SATA 0-2 HDD

Power Cables

Route all applicable

cables (see below)

through the baffle

notches and snap air

baffle into place.

The baffle is held in place by two

standoffs on the chassis floor.

Note: Front tab

of air baffle must fit

under the drive bay

cover prior to lowering

into chassis standoffs

to ensure a proper fit.

Drive Bay Cover

Power

Supply

SATA Connectors

Power

Supply

SATA 0 HDD

SATA 1 HDD

SATA 2 HDD

Fixed

SATA

Drive 0

Fixed

SATA

Drive 1

Optical Drive

Air Baffle

Install Fixed Hard Drives/Carriers

Slide each carrier

into a drive opening

until the blue carrier

latch clicks into place.

Repeat these steps for

each installed hard drive

CAUTIONS: If you install less than three drives,

empty drive bays must be occupied by carriers

with baffles to maintain proper system cooling.

To avoid possible damage to your chassis, use

only carriers that came with your server system.

Remove the Plastic Air Baffle

Install the hard

disk drive

and attach

with four

screws.

Install 1st drive

here.

Install 2nd

drive here.

Hard Drive Numbering Diagram

Carrier

Latch

Remove fixed drive carrier(s)

by pressing blue carrier latch

from inside the chassis, pushing

the drive carrier forward, and

sliding it out of the system.

Install 3rd

drive here.

Fixed

Drive 2

Optical

Device

Fixed

Drive 0

Fixed

SATA

Drive 2

Backplane

13a

Install SATA Optical Device (optional)

1. Remove the

Empty Tray

2. Install Device into the Tray

Align the two

holes on the

left edge of

the optical

device with

the two

metal tabs

in the tray.

3. Install Optical Device Tray

Assembly into the Chassis

Pull the power and

data cables through

the front of the

chassis opening.

Remove the empty

tray from the

accessory kit box.

Empty

Optical

Device Tray

Metal Tab

CAUTION:

To maintain

proper system cooling, a

filler blank must be

installed if you do not

install a device at this

location.

Optical

Device Tray

Assembly

Blue Release

Lever

Optical

Device Tray

Assembly

Optical

Drive

Data

Power

Connect the cables

as shown.

Lower opposite side of optical

device into the tray until it

clicks into place.

From the back side of the device

bay, pull the cables back into

the chassis opening as

you insert the device.

Verify that the blue

release lever on the

tray locks into place.

Note: The power end of the SATA optical device cable comes

attached to the midplane board power cable.

13b

Connect the SATA end of the cable to one of the server board

SATA connectors.

Server Board

SATA

Connectors

SATA Conn.

Detail

Power

Supply

SATA Cable

from Optical Device

4. Install Optical Device Data Cable

AXXHERAIL2

Cable Management Arm

Tool-less Rail Kit

ADWBEZBLACKBezel for Standard Control Panel

Optional Accessories and Order Codes

AXXRACKARM2

AXXBASRAIL13

Fixed Bracket Kit

Basic Slide Rail Kit

AXXBRACKETS

ADWLCDBEZEL

Bezel for Intel

Local Control Panel

Infiniband* I/O Expansion Module

AXXSATADVDROM

Slimline DVD-ROM/CD-ROM Drive

AXXLCPRACK2

Intel

Local Control Panel

AXXGBIOMOD

Dual Gigabit I/O Expansion Module

AXXSASIOMOD

SAS I/O Expansion Module

10 Gigabit I/O Expansion Module

AXXRMM3

AXXIBIOMOD

Intel

Remote Management Module 3

AXX10GBIOMOD

Quad-Port Gigabit I/O Expansion

Module

AXX4GBIOMOD2

Finishing Up

Before installing your operating system, you must finish

your system installation, make I/O connections, and plug in

AC power.

AC Power

CAUTION: This unit must

be operated with the TOP

COVER installed to ensure

proper cooling.

Video

1. Replace the system cover.

I/O Exp. Module

USB 0-3

Intel

RMM3 Module

Serial

Port A

Network

NIC1-2

2. Install the server into the rack using the instructions provided

with the rack mounting kit.

Connect your USB keyboard/mouse, video and other I/O

cables/devices as shown. Then connect the AC power cord.

Software

• BIOS, Drivers, and Operating System

Installation

C. Install your Operating System:

Use the instructions provided with the RAID

controller and with the operating system.

D. Install Operating System Drivers:

With the operating system running, insert the

Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating

system, the Express Installer will autorun and allow you to select the appropriate drivers

to install. On other operating systems, browse the CD folders to locate and install the

driver files.

A. Update the System Software:

1. Boot from the Intel

Server Deployment Toolkit CD.

2. Use the Wizard to access the latest versions on the Internet and update the BIOS,

firmware, FRUSDRs, and Intel

RMM3.

Note: You can also use downloaded files on a USB key.

B. Conﬁgure your RAID Controller:

If using a RAID card, use the instructions

provided with the RAID controller. If using on-board RAID, you must activate RAID in

the BIOS setup. See the Intel

Server Board S5520UR Technical Product

Specification for more information.

E. Install Intel

System Management Software (optional):

Download the latest version of the Intel

System Management Software from

http://www.intel.com/go/servermanagement and use the instructions provided at that

link to install the software.

Intel® Server Board S5520UR

Component Layout

See your Intel

Server System SR1600UR Service Guide for expanded component

and connection information.

Diag.

LEDs

USB

8, 9

USB

2, 5

Video

ID LED

Serial A

CPU 1

I/O Exp.

Module Conn. 1

I/O Exp.

Module Conn. 2

SGPIO

SATA Key

LCP/AUX IPMB

BMC Force

Update

Front USB

SSD

USB

Power

Supply

Signal

Conn.

Serial B

SATA 5

SATA 0

SATA 1

SATA 2

SATA 3

SATA 4

DIMM

Status

LEDs

CPU 2

Fan

Mem 2

Fan

CPU

Power

Front

Panel

CPU 2

Bridge Board Conn.

Sys 1

Fan

Sys 2

Fan

NIC1

NIC2

DIMM A2

DIMM C1

DIMM A1

DIMM B2

DIMM B1

DIMM C2

Main Power

Fan Board

DIMM Status LEDs

Battery

DIMM F1

DIMM D2

DIMM F2

DIMM E1

DIMM E2

DIMM D1

PCIe* Riser

RMM3 Conn.

CPU 1 Fan

Mem 1 Fan

Status

LED

BIOS

Recover

Password

Clear

BIOS

Default

Serial Port

Config.

Document/Tool

Available Documents

Technical Product Specification

Spares, Parts List, and Configuration Guide

Server Configurator Tool

Software and Drivers

Content

In-depth technical information

Supported accessories and spares list

Tested peripherals and operating systems list

Tested memory list

Supported processors list

Up-to-date firmware, driver, and utility information

A link to the above documents, Server Configurator Tool, and the Software and Drivers web page

can be found at: http://www.intel.com/p/en_US/support/highlights/server/s5520ur.

Summary of content (1 pages)

PAGE 1
C D E F I H G AB L E. Hard Drive Activity LED F. Status LED G. System ID LED C D E F K G H J AXXHERAIL2 AXXRACKARM2 AXXBASRAIL13 AXXBRACKETS ADWBEZBLACK ADWLCDBEZEL AXXSATADVDROM AXXLCPRACK2 E Connect the two cables to the USB and front panel connectors on the backplane as shown. H. System ID Button I. Reset Button J. USB 1.1 Port K. NMI (recessed) Button L. Video (hotswap drive system only) See your Intel® Server System SR1600UR Service Guide for expanded component and connection information.