Quick Start Guide Page 2

ManualsBrandsIntel ManualsOtherIntel Server Board S5520UR

Side 2

Install Second Power

Supply Module (optional)

Use the 'finger hole'

to remove the filler

panel.

To remove a power supply

module, push the green latch

in the direction shown while

pulling out of the system by

the handle.

Insert the power

supply module into

the power supply

cage and push all the

way until it clicks

into place.

Handle

PS Latch

Finger

Hole

Tape Drive

2.5 Inch

Fixed Drive

Install

Additional

Drives

(optional)

See the Service Guide for

instructions on installing an

optional tape drive, or two

additional 2.5 inch fixed drives.

Install Add-in Card(s)

Open rear retention clip by pushing blue

slide upward and rotating clip fully open.

Open front retention clip by pushing the

blue latch in the direction shown and

rotating clip 90 degrees outward.

Remove filler panel from the selected

add-in card slot.

Insert add-in card until it seats in the

riser connector.

Close both retention clips. Note: Make

sure that all empty add-in card slots

have filler panels installed.

• Full-height Side of PCI Riser Shown

Note: Add-in card install

sequence for low-profile add-in

cards on opposite side of PCI

riser is the same.

REMOVE Filler Panel

CAUTION:

Observe normal

ESD precautions

when installing add-in cards.

A complete list of accessories and spares can be found at: http://support.intel.com/support/motherboards/server/s5520ur/

Front Panel Controls and Indicators

Intel® Local Control Panel Standard Control Panel

O M L K J HIN G

J IK

BA F G HEDC

A NIC2 Activity LED

B. NIC1 Activity LED

C. Power/Sleep Button

D. Power/Sleep LED

E. Hard Drive

Activity LED

F. Status LED

G. System ID LED

H. System ID

Button

I. Reset

Button

J. USB 1.1

Port

K. NMI

(recessed)

Button

L. Video

A USB 1.1 Port

B. LCD Display

C. Menu Control Button - Up

D. Menu Control Button - Down

E. Menu Control Button - Left

F. Menu Control Button - Enter

G. ID LED

H. Power/Sleep LED

I. Power/Sleep Button

J. System Status

LED

K. NIC 2 Activity

LED

L. NIC 1 Activity LED

M. HDD Activity LED

N. Reset Button

O. USB 1.1 Port

Check RAID BBU

Battery Connection

Install RAID Battery Backup Unit

(BBU) (optional)

Install Intel® RAID Activation Key

and RAID Mini DIMM (optional)

Insert the Intel

RAID Activation Key into the midplane board

socket as shown. Make sure the key snaps into the socket.

Open RAID mini DIMM socket levers and insert connector

edge of mini DIMM into socket until levers close and snap

into place.

The RAID BBU has two hooks on

the underside. Align these hooks

with the matching chassis tabs,

then slide toward the power supply

to lock into place.

Connect the power cable between

the BBU and the midplane

board as shown.

Note: Backplane not

shown for clarity.

Midplane RAID

BBU Connector

Chassis

Tab(2)

Power

Supply

Battery

Backup

Unit

The RAID BBU has an internal

battery power cable. Open the

BBU case lid as shown.

If the battery power cable is not

connected,

connect the cable now.

Close and latch the BBU case lid.

Backplane Board not shown for clarity

Intel

RAID

Activation

Key Socket

RAID Mini DIMM

Socket

RAID Mini DIMM

RAID

Key

Open Levers

Midplane

Board

Install PCI Add-in Card Riser Assembly

Position the riser card edge

connector over the

server board riser

socket and align

the three hooks

in the riser with

the slots at

the back

of the

chassis.

To install the riser assembly:

Press down uniformly until the three

hooks on the rear of the PCI riser assembly

engage the chassis back panel slots.

The riser card will seat into the matching

socket on the server board.

Note: The PCI riser assembly

includes an intrusion switch that

engages the system cover.

Do not use the intrusion header

located on the server board.

Intrusion

Switch

Chassis Back Panel

Hook (3)

Riser

Socket

PCI

Riser

Assembly

Slot (3)

Riser Card

Connector

Server Board

Riser Socket

Hooks (3)

Install Optical Device

Insert the optical drive

into chassis opening and push

all the way until it stops.

Install the plastic guide

onto the back of the

drive and attach with

two screws as shown.

IMPORTANT NOTE: If you do not install a device at this location,

install the optical device bay filler panel shown below. This is

required to maintain proper system cooling.

Optical

Drive

Install Bezel

(optional)

Select the bezel that matches your control

panel and install as shown.

Standard Control

Panel Bezel

Intel® Local Control

Panel Bezel

Hard

Disk

Drive

Install Active System Components...for a Passive System, skip this step

Install Top Cover

Place top cover onto the chassis and

slide forward to engage recessed edge

at front of cover.

Install security screw. Note that

security screw re-installation is optional.

Install

Rack

Handles

Note: Rack handles are

required to install the bezel.

For detailed instructions,

see the Service Guide.

Document Type

Available Documents

Technical Product Specification

Spares, Parts List, and Configuration Guide

Software and Drivers

Content

In-depth technical information

Supported accessories and spares list

Tested peripherals and operating systems list

Tested memory list

Supported processors list

Up-to-date firmware, driver, and utility information

Server Configurator Tool

These documents can be found at:

http://support.intel.com/support/motherboards/server/s5520ur/

Replacing the Riser Card (optional)

Push back on the blue riser lever.

While holding the lever back, slide the

card firmly in the direction shown to

disengage the riser pins and remove

the riser card.

Remove the riser card

Push back and hold the blue lever

in that position.

Place the riser card onto

the retention pins.

Slide the riser card in the

direction shown to lock

it into place.

Release the blue riser

lever.

Install the replacement riser card

Riser Card

Blue Riser Lever

Riser Retention Pin

Install

Processor

Air Duct

Use care to avoid pinching system cables.

Processor

Air Duct

Install processor

air duct as

shown making

sure the front

edge of the duct

contacts the

fan module.

Install Hard Drives/Carriers

Remove the drive

carrier by pressing the

green latch to unlock.

Repeat these steps for each installed hard drive

Note: Carrier lever must be held in the FULLY

OPEN position to install into the chassis. Slide

carrier into chassis until it clicks, then close the

lever.

Pull out on the black

lever and slide the

carrier out.

Remove the plastic air baffle and

save for future use.

Install the hard disk drive

as shown.

Install hard disk drive assembly

into the chassis opening.

CAUTION: If you install less than eight

drives or devices, empty drive bays must

be occupied by carriers with baffles or with

a filler panel provided for drive locations 6

and 7 to maintain proper system cooling.

Drive 0 Primary

Hard Drive Numbering Diagram

Attach with

four screws.

Remove only when

installing hard drive device.

Keep for future use

Install Intel® Local Control Panel (optional)

Press the blue locking lever and

push forward to release the control

panel from the chassis.

Disconnect the two cables from

the back side of the backplane.

Slide control panel fully into chassis until the

locking lever engages.

Feed local control panel cables into chassis opening.

Connect the USB and data cables to the local control panel as shown.

Connect the two cables to the USB and

control panel connectors on the back

side of the backplane

as shown.

Remove Standard Control Panel Install Local Control Panel

Locking

Lever

Local

Control Panel

Slide the standard control panel

and cables out of the chassis.

Backplane

Locking

Lever

USB

Cable

Data

Cable

Finishing Up

Before installing your operating system, you must finish your system

installation, make I/O connections, and plug in AC power.

AC Power

CAUTION: This unit must

be operated with the TOP

COVER installed to ensure

proper cooling.

Video

1. Make sure the system top cover is installed.

I/O Module

Serial

Port A

Serial

Port B

Network

NIC1-2

USB 0-3

Video

Intel

RMM3

NIC Module

2. Install the server into the rack using the instructions provided

with the rack mounting kit.

Connect your USB keyboard/mouse, video and other I/O

cables/devices as shown. Then connect the AC power cord(s).

Software

• BIOS, Drivers, and Operating System Installation

B. Conﬁgure your RAID Controller:

If using a RAID card, use the instructions provided

with the RAID controller. If using on-board RAID, you must activate RAID in the BIOS setup. See

the Intel

Server Board S5520UR Technical Product Specification for more information.

C. Install your Operating System:

Use the instructions provided with the RAID controller

and with the operating system.

D. Install Operating System Drivers:

With the operating system running, insert the

Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the

Express Installer will autorun and allow you to select the appropriate drivers to install. On other

operating systems, browse the CD folders to locate and install the driver files.

A. Update the System Software:

1. Boot from the Intel

Server Deployment Toolkit CD.

2. Use the Wizard to access the latest versions on the Internet and update the BIOS, firmware,

FRUSDRs, and Intel

RMM3. Note: You may also used downloaded files on a USB key.

E. Install Intel

System Management Software (optional):

Download the latest version of the Intel

System Management Software from

http://www.intel.com/go/servermanagement and use the instructions provided at that link to install

the software.

Intel® Server Board S5520UR

Component Layout

See your Intel

Server System

SR2600UR/

SR2625UR

Service Guide

for expanded

component and

connection

information.

Diag.

LEDs

USB

8, 9

USB

2, 5

Video

ID LED

Serial A

CPU 1

I/O Exp.

Module Conn. 1

I/O Exp.

Module Conn. 2

SGPIO

SATA Key

LCP/AUX IPMB

BMC Force

Update

Front USB

SSD

USB

Power

Supply

Signal

Conn.

Serial B

SATA 5

SATA 0

SATA 1

SATA 2

SATA 3

SATA 4

CPU 2

Fan

Mem 2

Fan

CPU

Power

Front

Panel

CPU 2

Bridge Board Conn.

Sys 1

Fan

Sys 2

Fan

NIC1

NIC2

DIMM A2

DIMM C1

DIMM A1

DIMM B2

DIMM B1

DIMM C2

Main Power

Fan Board

DIMM Status LEDs

Battery

DIMM F1

DIMM D2

DIMM F2

DIMM E1

DIMM E2

DIMM D1

PCIe* Riser

RMM3 Conn.

DIMM

Status

LEDs

CPU 1 Fan

Mem 1 Fan

Status

LED

BIOS

Recover

Password

Clear

BIOS

Default

Serial Port

Config.

AXXHERAIL2

Cable Management Arm

Tool-less Rail Kit

AXXBASRAIL13

Basic Slide Rail Kit

ADRBEZBLACK

Bezel for Standard Control Panel

Optional Accessories and Order Codes

AXXBRACKETS

AXXRACKARM2

Fixed Rack Brackets

ADRLCDBEZEL

Intel

Remote Management Module 3

Bezel for Intel

Local Control Panel

AXXRMM3

AXXSATADVDROM

Slimline DVD-ROM/CD-ROM Drive

ASR2600FIXDRV

Fixed 2.5 inch Drive Mounting Kit

ASR2500SATAPE

SAS/SATA Tape Drive Mounting Kit

AXXLCPRACK2

Intel

Local Control Panel Module

AXX750WPS

750-W Power Supply

Infiniband* I/O Expansion Module

AXXGBIOMOD

Dual Gigabit I/O Expansion Module

AXXSASIOMOD

AXX4GBIOMOD2

AXX10GBIOMOD

SAS I/O Expansion Module

Quad-Port Gigabit I/O Expansion Module

10 Gigabit I/O Expansion Module

AXXRAKSAS2

RAID Mini DIMM

RAID Activation Key

AXXMINIDIMM512

AXXIBIOMOD