Quick Start Guide Page 2

ManualsBrandsIntel ManualsOtherIntel Server Board S5520UR

Side 2

Install

Rack

Handles

Note: Rack handles are

required to install the bezel.

For detailed instructions,

see the Service Guide.

Install Active System Components...for a Passive System, skip this step

Repeat these steps for

each installed hard drive

Remove fixed drive

carrier(s) by pushing the

green latch towards the

lever, opening the lever all

the way, and then pulling

the drive carrier out of

the system.

Remove the plastic air

baffle and save for

future use.

Note: Only drive locations 0-4 support

hot-swap SATA drives. Location

5 requires fixed drive(s).

CAUTIONS: If you install less than five drives,

empty drive bays must be occupied by carriers

with baffles to maintain proper system cooling.

To avoid possible damage to your chassis,

use only carriers that came with your server

system.

Note: Carrier lever must be held in

the FULLY OPEN position to

install into the chassis.

Install Hard Drives/Carriers

Install the hard disk

drive and attach

with four

screws.

Slide carrier into

chassis until it

stops, then

close the lever

until it snaps shut.

Drive 0 Primary

Drive Bay

Hard Drive Numbering Diagram

Tape Drive

6th Hard Drive

2.5 Inch

Fixed Drive

Install

Additional

Drives

(optional)

See the Service Guide for

instructions on installing the

optional sixth hard disk drive,

tape drive, or two 2.5 inch

fixed drives.

Install Bezel

(optional)

Select the bezel that matches your control

panel and install as shown.

Standard Control

Panel Bezel

Intel® Local Control

Panel Bezel

Install Intel® Local Control Panel (optional)

Slide the standard control panel out of the chassis.

Press the blue locking lever and push forward to release the

control panel from the chassis.

Make sure the control panel engages the

backplane connector.

Make sure the blue locking lever snaps into place.

Slide Intel

Local Control Panel into chassis.

Backplane

Board

Locking

Lever

Remove Standard Control Panel Module

Local

Control Panel

Standard

Control Panel

Backplane

Board

Backplane

Connector

Locking

Lever

Install PCI Add-in Card Riser Assembly

Position the riser card edge

connector over the

server board riser

socket and align

the three hooks in

the riser with the

slots at the back

of the chassis.

To install the riser assembly:

Press down uniformly until the three

hooks on the rear of the PCI riser assembly

engage the chassis back panel slots.

The riser card will seat into the matching

socket on the server board.

Note: The PCI riser assembly

includes an intrusion switch

that engages the system cover.

Do not use the intrusion header

located on the server board.

Intrusion

Switch

Chassis Back Panel

Hook (3)

Riser

Socket

PCI

Riser

Assembly

Slot (3)

Riser Card

Connector

Hooks (3)

Server Board

Riser Socket

Install Add-in Card(s)

Open rear retention clip by pushing blue

slide upward and rotating clip fully open.

Open front retention clip by pushing the blue

latch in the direction shown and rotating clip

90 degrees outward.

Remove filler panel from the selected

add-in card slot.

Insert add-in card until it seats in the riser connector.

Close rear retention clip. Push the blue slide upward

and press the clip to lock it into place.

• Full-height Side of PCI Riser Shown

Note: Add-in card install sequence for low-profile add-in

cards on opposite side of PCI riser is the same.

REMOVE Filler Panel

CAUTION:

Observe normal

ESD precautions

when installing add-in cards.

Close front retention clip and push the blue latch

forward to lock it into place.

Note: Make sure that

all empty add-in card

slots have filler panels

installed.

Front Panel Controls and Indicators

Intel® Local Control Panel Standard Control Panel

O M L K J HIN G

J IL K

BA F G HEDC

A NIC2 Activity LED

B. NIC1 Activity LED

C. Power/Sleep Button

D. Power/Sleep LED

E. Hard Drive

Activity LED

F. Status LED

G. System ID LED

H. System ID

Button

I. Reset

Button

J. USB 1.1

Port

K. NMI

(recessed)

Button

L. Video

A USB 1.1 Port

B. LCD Display

C. Menu Control Button - Up

D. Menu Control Button - Down

E. Menu Control Button - Left

F. Menu Control Button - Enter

G. ID LED

H. Power/Sleep LED

I. Power/Sleep Button

J. System Status

LED

K. NIC 2 Activity

LED

L. NIC 1 Activity LED

M. HDD Activity LED

N. Reset Button

O. USB 1.1 Port

Install Top Cover

Place top cover onto the chassis and

slide forward to engage recessed edge at

front of cover.

Install security screw. Note that security

screw re-installation is optional.

Install

Processor

Air Duct

Use care to avoid

pinching system cables.

Install processor air duct as

shown making sure the front

edge of the

duct contacts

the fan

module.

Processor

Air Duct

Install Second

Power Supply

Module

(optional)

Use the 'finger

hole' to remove

the filler panel.

To remove a power

supply module, push

the green latch in the

direction shown while

pulling out of the

system by the handle.

Insert the power

supply module

into the power

supply cage and

push all the way

until it clicks

into place.

Handle

PS Latch

Finger

Hole

Replacing the Riser Card (optional)

Push back on the blue riser lever.

While holding the lever back, slide the

card firmly in the direction shown to

disengage the riser pins and remove

the riser card.

Remove the riser card

Push back and hold the blue

lever in that position.

Place the riser card onto

the retention pins.

Slide the riser card in the

direction shown to lock

it into place.

Release the blue riser

lever.

Install the replacement riser card

Riser Card

Blue Riser Lever

Riser Retention Pin

Install Optical Device (optional)

3. Install Device into the Tray

2. Install the Interposer Board

4. Secure Interposer Board

to Device Tray

Plug the interposer board

connector into the

matching connector

on the back of

the optical

device.

Align the two holes

on the left edge of

the optical device

with the two metal

tabs in the tray.

Lower opposite side

of optical device into

tray until it clicks

into place.

Attach with

screw as shown.

Make sure interposer

board fits onto

alignment pin

on device tray.

Metal Tab

Drive Tray

Optical

Device

Connector

Interposer

Tray alignment pin

fits into this hole.

Insert optical device tray assembly

into the system.

Verify that the back of the interposer

board plugs into the matching

socket on the backplane and

the blue release lever on the

tray locks into place.

5. Install Optical Device Tray Assembly into the Chassis

For installing the optional USB floppy drive, note the location

of the backplane USB connector at right and refer to the

documentation that came with the device.

Optical Drive

Tray

Assembly

USB

Connector

Backplane

Release Lever

Interposer

Board

Remove the empty tray and screw

from the accessory kit box.

1. Remove the Empty Tray

For installing the optional USB floppy

drive in place of a CD-ROM, see #5 below

on the right.

CAUTION:

To maintain proper

system cooling, a filler blank

must be installed if you

do not install

a device at

this location.

Check RAID BBU

Battery Connection

Install RAID Battery Backup Unit

(BBU) (optional)

Install Intel® RAID Activation Key

and RAID Mini DIMM (optional)

Insert the Intel

RAID Activation Key into the midplane board

socket as shown. Make sure the key snaps into the socket.

Open RAID mini DIMM socket levers and insert connector

edge of mini DIMM into socket until

levers close and snap into place.

The RAID BBU has two hooks on

the underside. Align these hooks

with the matching chassis tabs,

then slide toward the power supply

to lock into place.

Connect the power cable between

the BBU and the midplane

board as shown.

Midplane RAID

BBU Connector

Chassis

Tab(2)

Power

Supply

Battery

Backup

Unit

The RAID BBU has an internal

battery power cable. Open the

BBU case lid as shown.

If the battery power cable is not

connected,

connect the cable now.

Close and latch the BBU case lid.

Backplane Board not shown for clarity

Intel

RAID

Activation

Key Socket

RAID Mini DIMM

Socket

RAID Mini DIMM

RAID

Key

Open Levers

Midplane

Board

Note: Backplane not

shown for clarity.

Finishing Up

Before installing your operating system, you must finish your system

installation, make I/O connections, and plug in AC power.

AC Power

CAUTION: This unit must

be operated with the TOP

COVER installed to ensure

proper cooling.

Video

1. Make sure the system top cover is installed.

I/O Module

Serial

Port A

Serial

Port B

Network

NIC1-2

USB 0-3

Video

Intel

RMM3

NIC Module

2. Install the server into the rack using the instructions provided

with the rack mounting kit.

Connect your USB keyboard/mouse, video and other I/O

cables/devices as shown. Then connect the AC power cord(s).

AXXHERAIL2

Cable Management Arm

Tool-less Rail Kit

ADRBEZBLACKBezel for Standard Control Panel

Optional Accessories and Order Codes

AXXRACKARM2

AXXBASRAIL13

Fixed Rack Brackets

Basic Slide Rail Kit

AXXBRACKETS

ADRLCDBEZEL

750-W Power Supply

Bezel for Intel

Local Control Panel

AXX750WPS

A complete list of accessories and spares can be found at:

http://support.intel.com/support/motherboards/server/s5520ur/

AXXSATADVDROM

Slimline DVD-ROM/CD-ROM Drive

ASR2600LCP

Intel

Local Control Panel Module

ASR2500SIXDRV

Sixth SAS/SATA Drive Mounting Kit

ASR2500SATAPE

SAS/SATA Tape Drive Mounting Kit

AXXRMM3

Intel

Remote Management Module 3

Infiniband* I/O Expansion Module

Fixed 2.5 inch Drive Mounting Kit

ASR2600FXDRV

Dual Gigabit I/O Expansion Module

AXXSASIOMOD

SAS I/O Expansion Module

10 Gigabit I/O Expansion Module

AXX10GBIOMOD

Quad-Port Gigabit I/O Expansion Module

AXX4GBIOMOD2

RAID Activation Key

AXXRAKSAS2

AXXMINIDIMM512

AXXIBIOMOD

RAID Mini DIMM

AXXGBIOMOD

Software

• BIOS, Drivers, and Operating System

Installation

C. Install your Operating System:

Use the instructions provided with the RAID

controller and with the operating system.

D. Install Operating System Drivers:

With the operating system running, insert

the Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating

system, the Express Installer will autorun and allow you to select the appropriate

drivers to install. On other operating systems, browse the CD folders to locate and

install the driver files.

A. Update the System Software:

1. Boot from the Intel

Server Deployment Toolkit CD.

2. Use the Wizard to access the latest versions on the Internet and update the BIOS,

firmware, FRUSDRs, and Intel

RMM3.

Note: You can also use downloaded files on a USB key.

B. Conﬁgure your RAID Controller:

If using a RAID card, use the instructions

provided with the RAID controller. If using on-board RAID, you must activate RAID in

the BIOS setup. See the Intel

Server Board S5520UR Technical Product Specification

for more information.

E. Install Intel

System Management Software (optional):

Download the latest version of the Intel

System Management Software from

http://www.intel.com/go/servermanagement and use the instructions provided at that

link to install the software.

Intel® Server Board S5520UR

Component Layout

See your Intel

Server System SR2600UR/SR2625UR Service Guide for expanded

component and connection information.

Diag.

LEDs

USB

8, 9

USB

2, 5

Video

ID LED

Serial A

CPU 1

I/O Exp.

Module Conn. 1

I/O Exp.

Module Conn. 2

SGPIO

SATA Key

LCP/AUX IPMB

BMC Force

Update

Front USB

SSD

USB

Power

Supply

Signal

Conn.

Serial B

SATA 5

SATA 0

SATA 1

SATA 2

SATA 3

SATA 4

CPU 2

Fan

Mem 2

Fan

CPU

Power

Front

Panel

CPU 2

Bridge Board Conn.

Sys 1

Fan

Sys 2

Fan

NIC1

NIC2

DIMM A2

DIMM C1

DIMM A1

DIMM B2

DIMM B1

DIMM C2

Main Power

Fan Board

DIMM Status LEDs

Battery

DIMM F1

DIMM D2

DIMM F2

DIMM E1

DIMM E2

DIMM D1

PCIe* Riser

RMM3 Conn.

DIMM

Status

LEDs

CPU 1 Fan

Mem 1 Fan

Status

LED

BIOS

Recover

Password

Clear

BIOS

Default

Serial Port

Config.

Document/Tool

Available Documents

Technical Product Specification

Spares, Parts List, and Configuration Guide

Server Configurator Tool

Software and Drivers

Content

In-depth technical information

Supported accessories and spares list

Tested peripherals and operating systems list

Tested memory list

Supported processors list

Up-to-date firmware, driver, and utility information

A link to the above documents, Server Configurator Tool, and the Software and Drivers

web page can be found at: http://support.intel.com/support/motherboards/server/s5520ur/