Multi FX 1U Manual Multi FX 1U Clockable Delay, Reverb and Chorus Effect Manual Revision: 2020.03.
Multi FX 1U Manual Table of Contents Table of Contents 1 Compliance 2 Installation 3 Before Your Start 3 Installing Your Module 4 Front Panel 6 Controls 6 Inputs & Outputs 9 Technical Specifications 10 Page 1
Multi FX 1U Manual Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Intellijel Designs, Inc. could void the user’s authority to operate the equipment.
Multi FX 1U Manual Installation This module is designed for use within an Intellijel-standard 1U row, such as contained within the Intellijel 4U and 7U Eurorack cases. Intellijel’s 1U specification is derived from the Eurorack mechanical specification set by Doepfer that is designed to support the use of lipped rails within industry standard rack heights. Before Your Start Intellijel Eurorack modules are designed to be used with a Eurorack-compatible case and power supply.
Multi FX 1U Manual Similarly, do not use open frames or any other enclosure that exposes the backside of any module or the power distribution board. You can use a tool like ModularGrid to assist in your planning. Failure to adequately power your modules may result in damage to your modules or power supply. If you are unsure, please contact us before proceeding. Installing Your Module When installing or removing a module from your case always turn off the power to the case and disconnect the power cable.
Multi FX 1U Manual Once connected, the cabling between the module and power supply should resemble the picture below: Before reconnecting power and turning on your modular system, double check that the ribbon cable is fully seated on both ends and that all the pins are correctly aligned. If the pins are misaligned in any direction or the ribbon is backwards you can cause damage to your module, power supply, or other modules.
Multi FX 1U Manual Front Panel Controls A. FX TYPE switch - 3-way switch determines whether Multi FX functions as a Reverb (REV), Delay (DLY) or Chorus (CHO). B. TIME knob - Adjusts the appropriate time-based parameter for either the REV (reverb), DLY (delay), or CHO (chorus) effect (as selected with the FX TYPE [A] switch), as labelled beneath the knob. Specifically: ● REV (reverb) Mode - If the FX TYPE [A] switch is set to REV, this knob controls the reverb’s PRE-DELAY time.
Multi FX 1U Manual If the delay is unclocked (i.e., the TAP TIME button not flashing), then the TIME [B] knob sets the delay from 50ms (fully counterclockwise) to 1000ms (fully clockwise) in several discrete intervals. ● CHO (chorus) mode - If the FX TYPE [A] switch is set to CHO, this knob controls the chorus RATE (as indicated by the label). Turn the knob clockwise to increase the chorus rate, and turn it counterclockwise to decrease the rate.
Multi FX 1U Manual D. TONE Knob - This knob is active for all three modes, and it controls a simple low pass filter. Turning it counterclockwise “dulls” the tone by decreasing the high frequency content. This can decrease the perceived ‘liveliness’ in the reverb, or allow for increasingly duller ‘taps’ as a delay fades out (as might happen with a tape delay). E. AMOUNT Knob - The function of this knob changes, depending on the mode you’ve selected with the FX TYPE [A] switch).
Multi FX 1U Manual Inputs & Outputs 1. OUT L - Left output jack. Some effects are stereo and some are mono. See below. 2. OUT R - Right output jack. Some effects are stereo and some are mono. Specifically: ● REV (reverb) Mode - The reverb effect is stereo. Should you wish to output a mono reverb signal, simply connect to either the OUT L or OUT R output. ● DLY (delay) Mode - The delay effect is mono, so the OUT L and OUT R output signals are identical.
Multi FX 1U Manual MULTI FX 1U is currently set to un-clocked mode, patching into the CLK jack will automatically turn clock mode on. The actual delay time is based on this input as well as the clock division set by the TIME/DIV [B] knob. The CLK input has an associated LED, which blinks in time with the clock input, regardless of the TIME/DIV knob position.
