Wireless Network IP Camera PROFESSIONAL SERIES Model 550703 User’s Guide LV2.
WIRELESS NETWORK IP CAMERA User’s Guide FCC Compliance Statement The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
WIRELESS NETWORK IP CAMERA User’s Guide Important Notice 1. Camera surveillance laws may differ for each country. Please contact the local authorities to avoid any surveillance law violations. 2. Please note that the CMOS lens that comes with the Wireless Network IP Camera can be damaged permanently if the camera lens is exposed to direct sunlight. If your application demands prolonged exposure to sunlight, you should consider equipping it with a sun visor. 3.
WIRELESS NETWORK IP CAMERA User’s Guide TABLE OF CONTENTS PRODUCT OVERVIEW 5 ABOUT WIRELESS IP NETWORK CAMERA MAIN FEATURES AND BENEFITS SYSTEM REQUIREMENTS 5 6 8 PHYSICAL DESCRIPTION 9 CONTENTS TOP VIEW AND DESCRIPTION REAR VIEW AND DESCRIPTION 9 10 11 INSTALLATION SUMMARY 12 ASSIGNING IP ADDRESS & ACCESSING NETWORK IP CAMERA HOME PAGE 13 ASSIGNING IP ADDRESS ASSIGNING IP ADDRESS BY USING IP INSTALLER CONNECTING WIRELESS NETWORK IP CAMERA TO A PC USING IP INSTALLER ASSIGNING IP ADDRESS BY USIN
WIRELESS NETWORK IP CAMERA User’s Guide CONFIGURING ADMINISTRATION TOOLS ADMINISTRATOR MENU OVERVIEW IMAGE CONFIGURATION NETWORK CONFIGURATION WIRELESS CONFIGURATION USER CONFIGURATION EVENT TRIGGER CONFIGURATION TIME CONFIGURATION SYSTEM CONFIGURATION 31 32 33 35 39 42 43 47 48 APPENDIX 50 A. TECHNICAL SPECIFICATIONS B. FAQ C. TROUBLE SHOOTING D. UTILIZING IP ADDRESSES ON LOCAL NETWORK INTRODUCTION IP CONSTRUCTION AND NETWORK CLASS C CLASS NETWORK E.
WIRELESS NETWORK IP CAMERA User’s Guide PRODUCT OVERVIEW About the Wireless Network IP Camera The Wireless Network IP Camera can be connected directly to Ethernet or Fast Ethernet networks and also supports wireless transmission based on the IEEE 802.11b standard. It is different from the conventional PC Web Camera; the Wireless Network IP Camera is as standalone system with builtin CPU and web-based solutions providing a low cost product that can transmit high quality video images for monitoring.
WIRELESS NETWORK IP CAMERA User’s Guide Main Features and Benefits Convenient Operation The Wireless Network IP Camera is a standalone system with built-in CPU requiring no special hardware or software such as PC frame grabber cards. The Wireless Network IP Camera supports both Active-X mode for Internet Explorer and JAVA mode for Internet Explorer and Netscape Navigator. Therefore, all that is required is a common web browser, such as Microsoft Internet Explorer 4.x or above.
WIRELESS NETWORK IP CAMERA User’s Guide Security Your Wireless Network IP Camera includes a self-contained web server, which means that digital images can be secured in the same manner as with any other Internet host. Your Network Administrator, using the unit’s security settings in combination with an organization’s Internet firewall, normally implements data protection. The Administrator can decide whether individuals, groups, or the whole world may access the camera.
WIRELESS NETWORK IP CAMERA User’s Guide System Requirements Network 10Base-T Ethernet or 100Base TX Fast Ethernet Wireless Local Area Network IEEE 802.11b Wireless LAN Recommended PC or Notebook to Access the Wireless Network IP Camera. System Requirements: CPU: Pentium II, 266 MHz or above Memory Size: 32 MB (64MB recommended) VGA card resolution: 800 x 600 or above Web Browser: Internet Explore 5.
WIRELESS NETWORK IP CAMERA User’s Guide PHYSICAL DESCRIPTION Contents Carefully remove all items from the package.
WIRELESS NETWORK IP CAMERA User’s Guide Top view and Description Network Activity LED Image Capture LED Operating status LED Image Capture LED (red): The Image Capture LED flashes when users are accessing the camera,. It flashes once when an image is being captured or saved. Operating Status LED (green): This LED indicates the Wireless Network IP Camera’s operating status.
WIRELESS NETWORK IP CAMERA User’s Guide Rear View and Description Antenna Connector RS 232 Connector Network Connector GPIO Connector Power Connector LAN/ WLAN-LAN/ WAN Power Connector: Only use the AC adapter provided by your dealer to avoid any possible damage from electric shock. Network Connector: For connection of 10baseT Ethernet or 100base TX Fast Ethernet cable.
WIRELESS NETWORK IP CAMERA User’s Guide INSTALLATION SUMMARY 1. Connect Ethernet and power to the Wireless Network IP Camera. 2. Install and launch the “IP-Installer” 3. Assign an IP address and network settings 4. Securely mount the Wireless Network IP Camera. 5.
WIRELESS NETWORK IP CAMERA User’s Guide ASSIGNING IP ADDRESS & ACCESSING THE WIRELESS NETWORK IP CAMERA HOME PAGE Assigning an IP Address To access the Wireless Network IP Camera, you need to assign an appropriate network IP address. IMPORTANT • Please use the newly assigned IP address, do NOT use any occupied IP address, the default, or the example IP address. • It is highly recommended that you assign an IP address before placing the Wireless Network IP Camera in a remote location or network.
WIRELESS NETWORK IP CAMERA User’s Guide Assigning an IP Address Using IP Installer (recommended) Connecting the Wireless Network IP Camera to a PC 1. Connecting with direct cable (Non Crossover UTP cable). Used when connecting the Wireless Network IP Camera to a switch, hub or router. Connect the Wireless Network IP Camera to a PC through a HUB 2. Connecting with Crossover UTP Cable. Use the crossover cable to directly connect the Wireless Network IP Camera to a PC.
WIRELESS NETWORK IP CAMERA User’s Guide Using IP Installer To install an IP address, you should use the IP Installer provided with Wireless Network IP Camera. You can also download the latest version of this program from the web site (http://intellinetnetwork.com). Note : System requirements for IP Installer: Microsoft Windows9x/NT/2000/XP. ① Execute the IP Installer after the Network IP Camera has completed the boot process (wait at least 15 seconds).
WIRELESS NETWORK IP CAMERA User’s Guide After entering all addresses for the Wireless Network IP Camera, click the “Change Network Configurations” button. The following message is displayed once all the information is set up properly. Click OK. NOTE After changing the Network Configuration, it will take about 15 seconds to reboot the Wireless Network IP Camera.. After that you may access the Wireless Network IP Camera Home Page.
WIRELESS NETWORK IP CAMERA User’s Guide Assigning IP Address by using Hyper Terminal (Advanced Users only) You can assign an IP address by using Hyper Terminal. In this case, you should configure Hyper Terminal first Configuring Hyper Terminal Hyper Terminal is a basic program for Windows 9x/NT/2000 and XP. A PC can communicate with external devices through the serial port by using this program.
WIRELESS NETWORK IP CAMERA User’s Guide ③ Configure bit/sec as 19,200 and leave the other settings at the default values. ④ The panel looks like this image when configured properly. (If it does not, repeat steps 1-4.
WIRELESS NETWORK IP CAMERA User’s Guide Assigning IP Address Follow these steps to assign an IP address using Hyper Terminal 1. Execute “Hyper Terminal” on your PC 2. Connect an RS232 Cable to the serial port of the PC that you have selected in Chapter 4.3.1 Configuring Hyper Terminal and the Wireless Network IP Camera serial port while Hyper Terminal is executed. 3. Supply power to the Wireless Network IP Camera. 4. A count down will start with the message “Press any key to stop auto-boot.” 5.
WIRELESS NETWORK IP CAMERA User’s Guide 6. You can see Network Configuration while [Boot] prompt is running by pressing ‘p’ key again. Here, inet on ethernet (e), host inet (h) and gateway inet (g) values are network configuration values. You should change these values in most cases. If you don’t know what values you should assign, contact the network administrator. Inet on ethernet (e) is the IP address and Subnet Mask address of the Wireless Network IP Camera.
WIRELESS NETWORK IP CAMERA User’s Guide the network on booting sequence. For more information on Wireless Network IP Camera upgrade, refer to “E. Updating Wireless Network IP Camera’s Newly Upgraded Program”. Gateway inet (g) is the gateway address of the Network Camera 7. Type ‘c’ to change the network configuration in [Boot] prompt. If you type ‘c’,, the Wireless Network IP Camera shows you the information you can change and the current assigned values. You can change as the following figure. 8.
WIRELESS NETWORK IP CAMERA User’s Guide Accessing the Wireless Network IP Camera Home Page After assigning the Wireless Network IP Camera an IP address, you may access Wireless Network IP Camera and monitor real-time images on the Internet. You may configure Wireless Network IP Camera within its own pages through any standard Web browser on a local or remote network. Starting Web Browser Start your web browser and enter your Wireless Network IP Camera’s IP address. Default IP Address http://192.168.1.
WIRELESS NETWORK IP CAMERA User’s Guide 1. ID and Password If you key in a user ID and password, you can access the camera to monitor real-time video. With Administrator’s ID and password, you can access real-time video with Administrative authority. The default value of both user ID and password are “admin” and the administrator may change it at the Administrator Menu. Each ID and password must be composed of no more than 10 bytes (e.g., 10 English letters).
WIRELESS NETWORK IP CAMERA User’s Guide The manual installation requires the user to have system administrator rights (Windows 2000 and Windows XP). Active-X Manual Installation If the Active-X program fails to install automatically, you may install it manually. The manual installation program can be downloaded as follows: Active-XVisit http://www.intellinet-network.com/driver/NetCam.
WIRELESS NETWORK IP CAMERA User’s Guide 4) Java Applet for Windows, Macintosh or Unix System user. Java Applet viewer is for a user who accesses the Wireless Network IP Camera through a computer that does not Utilize MS Windows Active-X, such as Macintosh computers. Java Applet viewer is run with Java Virtual Machine that is installed on the user’s computer. Macintosh and Unix/Linux Systems The Wireless Network IP Camera Active-X program is based on MS windows OS.
WIRELESS NETWORK IP CAMERA User’s Guide Wireless Network IP Camera Home Page Having completed the login procedure, you now see the Wireless Network IP Camera home page 1. Connected Client Shows the number of users currently connected to the camera (100 users can access the camera simultaneously). 2. Administrator Menu Provides access to the Administration menu.
WIRELESS NETWORK IP CAMERA User’s Guide 4. SAVE, STOP SAVE, SNAP SHOT, SHOW ONLY IMAGE ① SAVE, STOP SAVE Users can save real time images from the Wireless Network IP Camera. Press SAVE then select the folder where you want to save images. (The image is saved as an AVI file.) Once it starts to save the image, “Saving” message and XviD Status appear. To stop saving, press STOP SAVE. (Saving Mode) (XviD Status) NOTE You may view the saved image using Window Media Player or Real Player.
WIRELESS NETWORK IP CAMERA User’s Guide ② SNAP SHOT To save only one image, press SNAP SHOT and then select a folder. Save the image as JPG file. ③ SHOW ONLY IMAGE When you want to see only the video panel, press SHOW ONLY IMAGE. 5. Frame Rate You may choose image transmission speed. If you choose ‘Fastest”, you will get images at the fastest frame rate. The transmission speed depends on your network line’s capacity and PC’s performance.
WIRELESS NETWORK IP CAMERA User’s Guide ADJUSTING THE CAMERA LENS Adjusting the Focus In order for the Focus Assistant to access the full focusing range for your application environment, simply turn the lens in the clockwise or counter clockwise direction. Unless you are replacing the lens, do not unscrew it more than 1.0 mm. *Adjust the camera focus while reviewing the picture quality on your web browser. Lens 1.
WIRELESS NETWORK IP CAMERA User’s Guide Replacing the Lens Because the Wireless Network IP Camera is designed with a CS-Mount, the lens supplied with your product can be replaced with any standard C or CS lens typically used within the surveillance industry. Follow the instructions below to replace the supplied lens with any C or CS type lens: 1. Unscrew the Wireless Network IP Camera lens by turning the lens counter-clockwise 2. C-lens only: Attach the new lens to a C-CS adapter 3.
WIRELESS NETWORK IP CAMERA User’s Guide CONFIGURING ADMINISTRATION TOOLS You can control the configurations of the Wireless Network IP Camera by Administration Tools. Only authorized users can access administration tools. Non-authorized users attempting access will see the message: “You are not an administrator”. Press Administrator Menu to control all configurations for Wireless Network IP Camera.
WIRELESS NETWORK IP CAMERA User’s Guide Administrator Menu Overview The table below provides a one-step overview of the Administration Tools: Image Configuration To configure compression rate, image size, brightness, contrast, etc.
WIRELESS NETWORK IP CAMERA User’s Guide Image Configuration Example of Wireless Network IP Camera definable image attributes using the Focus Assistant: 1. Compression rate The file size of a JPEG-compressed image depends upon the actual content of the image. Images containing much detail will generate larger files. Image quality is controlled through the level of compression; where, high compression yields small files, while low compression maintains higher image quality at the expense of larger files.
WIRELESS NETWORK IP CAMERA User’s Guide 2. Image Size You may choose the image size VGA(640x480) or QVGA(320x240) and 160*120 Large image sizes (VGA) yield lower frame rates, while small sizes maintain higher frame rates 3. Vertical Flip Turns the image view upside down (affects only the web browser live view) 4. Horizontal Flip Switches the image view right from left (affects only the web browser live view) 5.
WIRELESS NETWORK IP CAMERA User’s Guide Network Configuration This screen defines the network type and addresses of the Wireless Network IP Camera. Here you can configure the Camera’s IP address, the DNS server address, and the Server IP address. Each configuration takes just a few seconds for booting after pressing SUBMIT. 1. Set IP Address, Subnet Mask, and Gateway Address. To set the IP Address, Subnet Mask, and Gateway Address manually, you may select “manually” in combo box.
WIRELESS NETWORK IP CAMERA User’s Guide Manual configuration can be done using the IP installer or the information on this page. (If you have trouble configuring network system information, please ask your Network Administrator for assistance.) To set DHCP, you may select ‘using DHCP’. When selecting “using DHCP”, the IP Address, Subnet Mask Address and Gateway Address may not be activated. Under DHCP selection, the IP address may be sent to an e-mail address whenever IP address is changed.
WIRELESS NETWORK IP CAMERA User’s Guide 6. PTZ port number (not useable in Wireless Camera) CAUTION Be careful not to use the same port number for Image Transfer Port Number and Upgrade port number. If it is duplicated, a warning message will appear. 7. ETSP port number Set the port number for ETSP [Event Trigger Setting Program]. (Default is “11000” and users can select from 8000 to 65535. For the detail of ETSP, please refer to the ETSP manual.) 8.
WIRELESS NETWORK IP CAMERA User’s Guide 11. DDNS Registration To register the Wireless Network IP Camera to a DDNS (Dynamic Domain Name Server), check the Enable box. A dynamic IP address complicates remote access since you may not know what your current WAN IP address is when you want to access your network over the Internet. The solution to the dynamic IP address problem comes in the form of a dynamic DNS service. (Please refer to the Appendix for details.) 12.
WIRELESS NETWORK IP CAMERA User’s Guide Wireless Configuration This screen is used to configure wireless settings to match your access pointer for a wireless network connection. Wireless Setup 1. Use the Connection Mode to determine the type of wireless communication for the Wireless Network IP Camera. There are two choices: Infrastructure Mode and Ad-hoc Mode. The default setting for the Connection Mode is Infrastructure Mode. 2.
WIRELESS NETWORK IP CAMERA User’s Guide Security Settings: Wireless network communications are easily intercepted. WEP (Wired Equivalent Privacy) is an encryption method specified by the IEEE 802.11b standard to make any intercepted communications extremely difficult to interpret by unauthorized parties. The WEP key needs to be entered in HEX code. To set up 64-bit WEP, input 10 HEX characters, for example, 0123456789.
WIRELESS NETWORK IP CAMERA User’s Guide Make sure the Encryption Code is the same as that of the access point the camera will be connected to under Infrastructure Mode. Your PC’s encryption code also needs to be set up to match the camera’s encryption code under either Infrastructure or Adhoc Mode. The default setting for the Encryption Key is Disable; therefore, to secure the wireless transmission, be sure to enable the Encryption Key by entering the relevant data.
WIRELESS NETWORK IP CAMERA User’s Guide User Configuration This screen is used to configure IDs and passwords for an Administrator and up to 5 users. 1. User Account (max. 10 characters) There is one Administrator account and 5 user accounts. Account names can be changed. 2. Password (max. 10 characters) If you want to open your Wireless Network IP Camera to everyone, you cannot change default user ID and password. However, you should change the administrator ID and password to a unique selection. 3.
WIRELESS NETWORK IP CAMERA User’s Guide Event Trigger Configuration This screen is used to designate an e-mail address or FTP server to receive captured images by setting SMTP or FTP settings. You may connect external devices such as an infrared sensor or alarm sensor to use with the provided terminal block (please refer to Appendix F – The I/O Connector). 1. Trigger Condition This is to select option how to send an event signal to theWireless Network IP Camera.
WIRELESS NETWORK IP CAMERA User’s Guide ② Motion detection from…… This is to detect motion from camera by S/W data comparison. When you select Motion Detection, the Wireless Network IP Camera detects a motion triggered by the camera lens. To detect motion, the camera compares a previous and present image. Motion is detected when, the camera recognizes a data change. This feature does not work if the image is too dark. Also, the Motion Detection only works reliably at a maximum image resolution of 320x240.
WIRELESS NETWORK IP CAMERA User’s Guide ⑤ Append to the image file name You may append some information to the Image file name A. Camera IP address : Example: “file name _192.168.1.19”.JPG B. Date and time : Example: “file name_20020218150030.”JPG C. Trigger condition flag 1. If choosing “Activation of digital input port”, “D” may be appended to image file name. Example: “file name_D.”JPG In case of choosing “Periodically every…”, “P” is appended to image file name. Example: “file name_P”.JPG D.
WIRELESS NETWORK IP CAMERA User’s Guide 3. Trigger Output This is to configure digital output states and control script. The Wireless Network IP Camera sends captured images via e-mail or FTP server when connected external sensors detect events. ① External devices signal output This is to supply voltage to output port when events are triggered. (This option is only activated when you select “Activation of digital output” option in previous “Trigger Condition” option.
WIRELESS NETWORK IP CAMERA User’s Guide Time Configuration This screen is used to configure date and time. 1. Synchronized with NTP server The Wireless Network IP Camera automatically configures date and time through the NTP (Network Time Protocol) server. The NTP Server is based on Greenwich time. Select NTP server, IP address and Time Zone to set the date and time automatically, then press SUBMIT.
WIRELESS NETWORK IP CAMERA User’s Guide System Configuration This screen is used to configure camera name, location and public image access. It also lets you remotely restart the camera and restore the factory default values. 1. Camera name This is to configure camera name for the front-page view. Camera name should be limited to 15 bytes, which are equal to 15 English characters. 2. Camera location This is to configure camera location for the front-page view.
WIRELESS NETWORK IP CAMERA User’s Guide 4. Direct public access to image via HTTP The camera supports a method to access the live image directly without logging in to the camera. The URL is: http://camera_ip/jpg/image.jpg. If direct public access is enabled, the image can be accessed without entering username and password. If direct public access is disabled, a valid username and password must be provided.
WIRELESS NETWORK IP CAMERA User’s Guide APPENDIX A. Technical Specifications Image Resolutions supported: 640x480, 320x240, 160x120 Standard JPEG Compression – 10 levels of compressions Frame Rates: Up to 8 fps at 640 x 480 resolution and 30 fps at 320x240 resolution Network 10baseT Ethernet or 100baseTX Fast Ethernet Twisted pair category 5 cables, Standard RJ45 connector IEEE802.
WIRELESS NETWORK IP CAMERA User’s Guide 4M flash memory SDRAM 8Mbyte 12V Power supply adapter included Under 6W power consumption System Requirements Operating systems: Windows 9x, Windows NT/2000, Linux, Linux, MaOSc, etc. Internet Explorer 4.0 or higher. JAVA support for MacOS, Linux and Windows. I/O Connector D-sub 9pin RS232 connector 1 Input to trigger the camera on external events.
WIRELESS NETWORK IP CAMERA User’s Guide B. Frequently Asked Question (FAQ) 1. What is a Network IP camera? A Network IP Camera is a stand-alone device which allows a user to view live, full motion video from anywhere on a computer network, even over the Internet, using a standard web-browser. 2. Are all Network IP cameras the same? No, some network cameras have an embedded OS (operating system) as well as an embedded Web server.
WIRELESS NETWORK IP CAMERA User’s Guide 8. How does the built-in motion detection work? It very simply compares what it sees now to what it saw in the last frame and based on a sensitivity you select will trigger an event. The event can be to send an e-mail, to send an Image to a FTP server, or to send a series of images (before and after the motion is detected) to an e-mail address or FTP server.-All required software is built into the camera. 9.
WIRELESS NETWORK IP CAMERA User’s Guide C. Trouble Shooting This appendix provides useful information to help you to resolve any difficulty you might have with your Wireless Network IP Camera. Fault symptoms, possible causes and remedial actions are provided within a quick reference table.
WIRELESS NETWORK IP CAMERA User’s Guide Symptoms, Possible Causes and Remedial Actions Symptoms Wireless Network IP Camera cannot be accessed from a web browser The Power LED is not constantly lit Possible causes The IP address is already used by another devices The IP address is located within a different subnet Remedial actions 1.Disconnect your Wireless Network IP Camera from the network 2. Run the PING utility (as described in PINGing your IP Address).
WIRELESS NETWORK IP CAMERA User’s Guide Your Wireless Network IP Camera works locally, but not externally. Check the Internet firewall with your network administrator. Firewall protection Default routers required The Internet site is too heavily loaded A series broad vertical white lines appear across the image. The CMOS sensor becomes overloaded when the light is too bright. This can happen e.g. with sun light reflexes.
WIRELESS NETWORK IP CAMERA User’s Guide D. Utilizing IP Addresses on Local Area Network Introduction Access to the Internet is achieved via Internet IP addresses. Currently, IP addresses are limited. There are 5 classes of networks, and each network contains IP addresses. A network can only hold a limited number of IP addresses. The number of IP addresses depends on the network class. The 5 classes are labeled “A” through “E,” with the most common one being the “C” class network.
WIRELESS NETWORK IP CAMERA User’s Guide C Class Network 1. Features of Addresses IP address: The three-digit number in room ‘X4’ is for the Host ID. The number ranges from 0 to 255. Among the numbers, 0 is used for Network ID, 1 is used for Router IP (Gateway address) and 255 are used for Broadcast address. The numbers from 2 to 244 are IP addresses that can be assigned to Wireless Network IP Cameras, PCs, etc. Network ID: Identifies a network. Generally the first number assigned is Network ID.
WIRELESS NETWORK IP CAMERA User’s Guide ③ To use as three sub-networks (1/4 + 1/4 + 1/2) Sub-Network ID: xxx.xxx.xxx.0 Gateway Address: xxx.xxx.xxx.1 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.63 IP Addresses: xxx.xxx.xxx.2 – xxx.xxx.xxx.62 Sub-Network ID: xxx.xxx.xxx.64 Gateway Address: xxx.xxx.xxx.65 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.127 IP Addresses: xxx.xxx.xxx.66 – xxx.xxx.xxx.126 Sub-Network ID: xxx.xxx.xxx.128 Gateway Address: xxx.xxx.xxx.
WIRELESS NETWORK IP CAMERA User’s Guide Sub-Network ID: xxx.xxx.xxx.192 Gateway Address: xxx.xxx.xxx.193 Subnet Mask: 255.255.255.192 Broadcast Address: xxx.xxx.xxx.255 IP Addresses: xxx.xxx.xxx.194 – xxx.xxx.xxx.
WIRELESS NETWORK IP CAMERA User’s Guide E. Updating Firmware CAUTION The process to update the current firmware is already installed into your Wireless Network IP Camera Follow the instruction in this manual. During the process, do not expose the camera to physical shock nor disconnect network and power. Otherwise, your Wireless Network IP Camera can be damaged seriously, which may result improper operation or failure.
WIRELESS NETWORK IP CAMERA User’s Guide Install New Firmware The Wireless Network IP Camera can be upgraded via the LAN or remotely over the Internet. Follow these steps to install new firmware: ① Confirm that the Wireless Network IP Camera is connected to your PC. (As long as you can access your Wireless Network IP Camera Home page, you can upgrade its firmware.) ② Execute the upgrade utility (included in ZIP file).
WIRELESS NETWORK IP CAMERA User’s Guide F. The I/O Connector The I/O Connector provides the physical interface to a digital output, and a single digital photocoupled input that is used for connecting a variety of external alarm devices to the Wireless Network IP Camera; including, IR-sensors, switches and alarm relay. In combination with the configurable alarm facilities, you can quickly develop a variety of security applications that are triggered on time- or alarm-based events.
WIRELESS NETWORK IP CAMERA User’s Guide G. RS 232 CABLE The Serial Connector In absence of a local network connection, the RS232 serial connector provides a physical interface for connecting a PTZ device or computer to the Wireless Network IP Camera. This means that Wireless Network IP Camera can operate as a standalone unit, -independent of any computer network. Users can connect to theWireless Network IP Camera by external mode.
WIRELESS NETWORK IP CAMERA User’s Guide H. Dynamic Domain Name Service (DDNS) Your internet Service Provider (ISP) provides you at least one IP address which you use to connect to the Internet. The address you get may be static, meaning it never changes, or dynamic, meaning it’s likely to change periodically. Just how often it changes depends on your ISP.
WIRELESS NETWORK IP CAMERA User’s Guide How to use ODS DDNS service 1. Access ODS home page (www.ods.org). 2. To register your ID, select REGISTER and then register your ID/ password. After that just log in with registered ID/password. 3. After you log in, you will see the following page.
WIRELESS NETWORK IP CAMERA User’s Guide If you want to use normal DDNS service among many services, you should fill in the blanks in the circled box and then click “Add Host.” ① Host: write the name you want. ② Domain: Select the domain you want (i.E. sphere-web.com) ③ Type: Select ‘A’ (‘A’ is normal) ④ Target: Write initial IP of equipment but just write any IP address that is in the form of “xxx.xxx.xxx.xxx” ⑤ TTL Priority: DO NOT select. This is an option. If you want to select “intellinet.sphere-web.
WIRELESS NETWORK IP CAMERA User’s Guide How to use DynDNS DDNS server 1. Access the Dyndns home page (www.dyndns.org). 2. If you didn’t register your ID, click “Sign Up Now” and then register your ID. Otherwise, login with registered ID.
WIRELESS NETWORK IP CAMERA User’s Guide 3. Click “Add Host”, and then go to the next page.
WIRELESS NETWORK IP CAMERA User’s Guide 4. Enter the domain name you want and leave other items unchanged, and then Click “Add Host” button to register. If you want to know details of any field, please refer to FAQ for each home page. 5. You will see this confirmation page.
WIRELESS NETWORK IP CAMERA User’s Guide DDNS registration for the Wireless Network IP Camera 1. After you set ODS or DynDNS successfully, you should move to administration -> network configuration. 2. In DDNS Registration, select DDNS server (ODS or Dyndns) you want. Enter ID/password that you registered and fill domain name that you set in each home page. (ex: intellient.ods.org) Before setting DDNS, you should register ID/password and domain name in ODS or Dyndns DDNS service. 3.
WIRELESS NETWORK IP CAMERA User’s Guide I. High-Speed Solutions This information is to help you access high-speed Internet services, such as xDSL, or a cable modem connection. However, since some high-speed Internet services may provide only one external IP address that may not be static,, there are several practical issues to consider.
WIRELESS NETWORK IP CAMERA User’s Guide ROUTERS AND FIREWALLS Another solution is to use one of several small routers/firewalls currently available on the market. These provide the necessary NAT functionality and allow complete independence for your PC, which can be switched off or rebooted without affecting the image transmission from your Wireless Network IP Camera.
WIRELESS NETWORK IP CAMERA User’s Guide J. Reinstating the Factory Default Settings This information explains how to set the default settings in the Wireless Network IP Camera. In certain circumstances it may become necessary to restart or reinstate the Factory Default settings for your Wireless Network IP Camera: This is performed by pressing the Reset Button, or using the Hyper Terminal Setting.
WIRELESS NETWORK IP CAMERA User’s Guide By Using Hyper Terminal (Advanced Users only) ① Execute Hyper Terminal as described in Chapter “4.3.1 Configuring Hyper Terminal” ② Supply the power to the Wireless Network IP Camera. ③ After a while, the count down starts with the message “Press 'p' key to stop auto-boot or Load-Default-Button under the NetCam for 3 seconds...” .At this time, press the ‘p’ key. Then, [Wireless Network IP Camera Boot] prompt shows like the right side image.
WIRELESS NETWORK IP CAMERA User’s Guide K. Glossary of Terms Active-X – A control (or set of rules) used by a browser. Active-X controls are often downloaded and installed automatically as required. ARP – Address Resolution Protocol. A method for finding a host's Ethernet address from its Internet address. The sender broadcasts an ARP packet containing the Internet address of another host and waits for it (or some other host) to send back its Ethernet address.
WIRELESS NETWORK IP CAMERA User’s Guide HTML – A markup language used to structure text and multimedia documents and to set up hypertext links between documents, used extensively on the World Wide Web. HTTP – A protocol used to request and transmit files, especially web pages and webpage components, over the Internet or other computer network. Intranet – A privately maintained computer network that can be accessed only by authorized persons, especially members or employees of the organization that owns it.
WIRELESS NETWORK IP CAMERA User’s Guide TCP/IP (Transmission Control Protocol/Internet Protocol) –. The wide-area-networking protocol that makes the Internet work. TCP/IP is used on many networks, including the Internet. TCP keeps track of the individual packets of information and IP contains the rules for how the packets are actually sent and received. URL (Uniform Resource Locator) – An “address” on the network.
WIRELESS NETWORK IP CAMERA User’s Guide Limited Lifetime Warranty * This INTELLINET ACTIVE NETWORKING® product is covered by the following warranty. * This warranty applies to the original purchaser only. This warranty covers defects in material and workmanship for the life of the original purchaser, for as long as the product is owned by the original purchaser. Implied warranties end when the original purchaser no longer owns the product; this limitation includes the implied warranty of merchantability.
