PoE Web-Smart Switch Model 502917 User’s Manual
FCC Warning This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table Of Contents Chapter 1 ...................................................................................................... 1 Introduction ............................................................................................... 1 Key Features . ........................................................................................... 2 Chapter 2 .................................................................................................... 3 Package Contents .............................
Chapter 1 . 8 Ports Power Over Ethernet Switch Introduction The 502917 is 8port Power Over Ethernet Switch consists 8 PSE/ Ethernet ports that is powered, detecting, classification capability, and programmable PD disconnect sensing, and with additional 8 10/100Mbps Ethernet port. That solves limitation of power outlet location offer system designer flexible solution to locate network device wherever.
Key Features • 10/100 auto-sensing ports — automatically detect optimal network speeds • IEEE 802.3af-compliant RJ-45 PSE/PoE output ports • Power output up to 15.
Chapter 2 Package Contents Before you start to install the Switch, please verify your package that contains the following items: One 8 port Power Over Ethernet Switch Rack-mount Kit For Rack Installation One Power Cord One User’s Manual Note: If any of these items is found missing or damaged, please contact your local supplier for replacement.
Chapter 3 Front Panel Layout A. Function of 8 RJ-45 Ports There are 8 ports RJ-45 connectors on the front panel, and all ports has build IEEE802.3af PoE/PSE, is for the connecting with Powered Device (PD) device. B. LED Indicators of 8 Port 10/100Mps Switch LED Power PD Link Color Status Description No. Of LED Yellow On Green On Off 10/100M Green On Off LINK/ACT.
C. LED Definitions Power LED On Off The unit is powered on and ready for use. The unit is powered off. PD link On Off Link to a PD device, the port supply power output No PD device link, no power request from the device 10/100M LED On Off The port is on the 100Mbps status. The port is on the 10Mbps status. LINK/ACT LED On Flashing The port is ready for 10/100Mbps connection. The data is transmitted or received on the port. Rear Panel Layout A. AC Power Input.
Chapter 4 Rack Mounting Optional Rack-mounting brackets are available to mount 502917 in standard EIA 19-inch rack. 502917 is supplied with two mounting brackets and eight screws. And please assemble according to the following steps. First, put the 502917 on the flat surface. Locate the mounting brackets on the sides of the Switch with the mounting holes on each. Next, insert the screw through the bracket and into the bracket mounting holes in the 502917. Then, place the Switch in to 19-inch rack.
Chapter 5 Installation How to connect the 502917 to PD device and existing Switch Connect straight-through twisted-pair cable (Cat. 5) from existing Switch to the input (Data) port of 502917, then connect the Output (Data+Power) port to the PD device, such as Wireless AP, Another switch with PD function…etc.
Chapter 6 Technical Specifications Standards • IEEE 802.3 (10Base-T Ethernet) • IEEE 802.3u (100Base-TX Fast Ethernet) • IEEE 802.3x (flow control, full duplex mode) • IEEE 802.3af (Power over Ethernet) General • Media support: - 10Base-T Cat3, 4, 5 UTP/STP RJ-45 - 100Base-TX Cat5 UTP/STP RJ-45 • Ports: 8 RJ-45 10/100 Mbps PoE ports • Packet filter/forwarding rate: - 148.800 pps (100 Mbps) - 14.
Package Contents • PoE Web-Smart Switch • Power cable • User manual A. ANSI/TIA/EIA-568-A PLUG & Twisted-pair Cable The IEE802.3u Standards permits the use of category 3, 4, 5 or better balanced cable pairs, installed according to ANSI/EIA-568-A. This appendix provides pinout and brief information for the CAT5 unshielded twisted pair cables . B.
C. Recommend CAT5 UTP specifications Physical: FR-PVC cable construction Cable Type: 4-pair unshielded-twisted pair solid copper Conductors: 24 AWG, solid bare annealed copper Operating temperature: -20 0C to +75 0C Electrical: Impedance: 100 ±15 % Near-End Cross-talk: 38dB @ 100 MHz Attenuation: 22 dB/100 m typical @ 100 MHz Maximum DC resistance : 9.
